Vetek VB2 Series User manual

page 1
Hantverksvägen 15,
76493 Väddö, Sweden. Tel [phone]
i[email protected]
www.vetek.com
Manual Weighingblock VB2 series and Uniscale
Note: At page 8 in this manual you will find a short form instruction. Normally the only
instruction shipped together with the Scale.
Normal Calibration
Calibration
switch
ON
PRINT
NET
GROSS
OFF
ZERO
TARE
Communica-tions
port
External power
9 VDC
Alkaline
batteries
The Weighingblock is a robust Scale. It is designed for portable use. When
transported by car between different working places we recommend using of a
protected space or a case. This will extend the interval for service.
Overview different ranges.
Model
Model
Capacity / Graduation
VB2-30-EC
Max 30 kg / 10 g
VB2-100-EC
Max 100 kg / 10 (50) g
VB2-200-EC
Max 200 kg / 20 (100) g
VB2-200-EC-TM
Max 200 kg / 100 g
VB2-200-50-TM
Max 200 kg / 50 g
VB2-30-05
Max 30 kg / 5 g
VB2-100-02
UNISCALE 100kg/2g
Max 100 kg / 2 g
VB2-100-10
Max 100 kg / 10 g
WS-130
Max 130 kg / 10 g (special)
VB2-130-10
UNISCALE 130kg/10g
Max 130 kg / 10 g
VB2-200-10
Max 200 kg / 20 g
UNISCALE 200kg/5g
Max 200 kg / 5 g
UNISCALE 200kg/50g
Max 200 kg / 50 g
Manual_VB_V2

page 2
[email protected]
www.vetek.com
Table of contents Page
Introduction, Keyboard Functions 2
Configuration and Setup Menu. Display 3
Parameters 4
Calibration 5
Specifications and Displayed Error Codes 6
Fault localization and repair 7
Instruction for handling 8
Solenoid module VBB-10 9
Introduction
Veteks newVB2 seriesofWeighingblocks are rugged digital scale casted in strong aluminum. It comes standard with a large (.75") LCD
screen for easy readout. All setup parameters may be entered via the membrane panel keys. The Scale has an ”intelligent” auto
power off function and isequippedwith6 pcs alkaline 1,5 V batteries LR6/AA. If the battery is not good enough to ensure a
correct value the scale will turn off.
The scale is developed especially for weighing of refrigerant cylinders, and to control when transferring refrigerants to other cylinders or
equipments. The scales setup parameters are altered through the Setup menu while a few other parameters are altered
through the User menu The configuration section of the manual explains how to use the five front panel keys to
maneuver and save settings in both menus.
There are categories of Scales: Non - Automatic weighing instruments and Automatic weighing instruments.
Weighingblocks and other Scales used only for weighing e.g. cylinders are Non - Automatic weighing instruments. When
using a Non - Automatic scale in commercial purpose in any of the EC countries it is prescribed by law that the scale
must be EC-type approved. If the purpose not is commercial or the Scale is used as an automatic batching Scale there is
no legal demands.
If the Scale is used as a Batching Scale it is an Automatic weighing instruments and there is no legal demands. But this
has to be checked with the authorities in each country.
VB2seriesofEC-typeapprovedWeighingblocks:
Theparametersshallnoteverbechangedbecauseoftheapproval.Authoritymustdotheverification.Theuserneedsagoodacknowledge
aboutallrulesandthelaws.Togetcompleteinformationwerecommendtakingalookathttp://www.sp.seorotherauthoritieswebsites.
VB2seriesofnot approved Weighingblocks:
Cannotbe verified
The Weighingblocks are suitable for use in weighing applications as: refrigeration cylinders, fire protection
cylinders, CO2, cylinders, parcels, persons, etc.
Keyboard functions
The calibration switch is only for calibration.
Indicator ON
In not EC-type approved version: Sends "Print"datatoprinterifscaleisstableandnotin
overload.Notactivewhen"Continuous"optionisselectedinUserMenu.
“Dot”.Extendedgraduationto10gforVB2-100-ECand20gforVB2-200-ECwhenpushed
and5secafterrelease.
TogglesbetweenGrossandNetweightdisplayonlyifaTarehasbeenestablished.
Setsscaletodisplay"0" wheninGrossmode,andwithinzerobandrange.Whenpushed
infor3seconds, theScaleswitchesoff.
UsedtoestablishaTare(zerotheScale)whileineitherGrossmodeor
Netmode.ThisoperationcannotbeperformedatorbelowGrosszero.
ON
PRINT
NET
GROS
S
OFF
ZERO
TARE
Hantverksvägen 15,
76493 Väddö, Sweden. Tel [phone]

page 3
Configuration
Setup menu.
To do this configuration you need to have a good acknowledge how a digital electronic Scale works. Note: If the
Scale fails, it is not always sure the Scale needs a configuration.
ExcepttheNormalMenytheWeighingblockhastwomenus.
The Setup menu, containing most of the indicator's functional Setup parameters, consists of 15 separate menu selections,
eachwithits ownsub-menuof choices.
The User menu, except A5 and A10 containing most of the indicator's serial communication parameters, which not are
showninthismanual.
SETUP MENY
1. Turn the power OFF.
2. Put Calibration Switch to the Calibration position.
3. Turn the indicator ON.
4. The display shows "F1" to indicate that the unit is in Setup menu mode.
5. To move to a new “F” heading, use TARE or ON to move up or down.
6. To move to the selection value, press ZERO once.
7. IncreaseanddecreasethevaluewithPRINT andTARE.
8. To save the value, press NET.
9. Press Dot to go back to parameter number.
10. To go back to normal menu put Calibration Switch to the Normal position.
NOTES ON THE SETUP MENU
There is an F21 sub-menu present that is for FACTORY USE ONLY!
DISPLAY
LCD Enunciator
MEANING
0
Better known as the “Center of Zero” enunciator, this light is active whenever the displayed
weight is within ± 0.25 divisions of true zero.
N
Indicates that the indicator is displaying net weight.
G
Indicates that the indicator is displaying gross weight.
T
Indicates that a tare weight has been established in the system.
lb, kg
Indicates the unit of the displayed weight (normally disabled).
bAtt
Indicates a low battery condition. Re-charge the battery or replace if alkaline batteries.
Indicates stable weighing.
VB2 Enunciator Definitions
PARAMETER DESCRIPTION CODE/VALUE
ON
PRINT
NET
GROSS
OFF
ZERO
TARE
Hantverksvägen 15,
76493 Väddö, Sweden. Tel [phone]
[email protected]
www.vetek.com

page 4
Tel [phone]
F1
Graduations
Specifies number of the Weighingblocks graduations. Value should be
consistent with legal requirements and environmental limits on the useful
system resolution.
500 1000 1500
2000 VB2-100-EC / 200-EC 2500
3000 VB2-30-EC 4000 5000
6000: VB2-30-05 8000
10000: VB2-100-10 / 200-20
13000: WS-130
F2
Sampling rate
Sampling rate. 10 or 80Hz. Only choose 80hz for very fast weighing
applications. Normally always 10hz is chosen.
80
10: all versions
F3
Zero Track Band
Selects the range within which the scale will automatically zero. Note that the
scale must be in standstill to automatically zero. Selections are in Display
Divisions. “d” = graduation
0d, 0.5d: , 1d: all EC-versions
3d: all other versions 5d
F4
Zero Range
Selects the range within which the scale may be zeroed. Note that the
indicator must be in standstill to zero the scale.
100%(US) 1.9%(CE)
2%: all EC versions
20%: all other versions
F5
Motion Band
Sets the level at which motion is detected by comparing the present display
update with the previous one. If motion is not detected for two seconds or
more, scale is in standstill and can process a Print or Zero command.
Maximum value varies depending on local regulations.
0,25 1d 3d all
versions
5d 10d
F6
Digital Filter
Averages weight readings to produce higher accuracy. The higher the filter
number, the greater the accuracy but the slower the response time. Choose 4
or 8 unless a very fast response is needed.
1 2
4 8 all versions
F7
Overload Limit
Selects the desired formula which determines the point at which the indicator
shows overload (""). All selections are based on the primary unit
selected in F8. "FS" = Full scale in primary units.
FS FS + 2% all none EC ver.
FS + 1d FS + 9d all EC ver.
F8
Calib. Unit
Selects the primary base unit to be used in the calibration process. Also the
default unit for normal operation. "1" = primary unit is lb. "2" = primary
unit is in kg.
1
2 all versions
F9
Display Div.
Determines the desired weight increments. Value should be consistent with
legal requirements.
1: VB2-100-10/30-EC, WS-130
2: VB2-200-20
5: VB2-100-EC/30-05/100-50
F10
Decimal Pt.
Determines location of the decimal point.
0 0,0
0,00 all versions except VB2-30-
05
0,000 VB2-30-05 0,0000
F11
Batching funct.
Activating Batching function (not be used with “EC”-Scales)
0: Approved Scales
1: Not Approved Scales
2: for scales with set points (F13,14)
F13
Set point 1
For special versions only
Any value.
F14
Set point 2
For special versions only
Any value.
F16
Zero Calibration
Places indicator into the zero calibration routine. Scrolling down with the
ZERO key one level begins the procedure.
Press ZERO key to begin
sequence
F17
Span Calibration
Places indicator into the span calibration routine. Scrolling down with the
ZERO key one level begins the procedure.
Press ZERO key to begin
sequence
F21
Factory Reset
This sub-menu will reset all parameters in the “F” and “A” menu to the default
settings. USE WITH CAUTION!
Press the ZERO key twice to
execute.
A5
Disable the lb/kg
Key
Allows the lb/kg key to be disabled so that an operator cannot accidentally
press the key and change the displayed units.
"0" = Disable the lb/kg key "1" = Enable the lb/kg key
”2” Activate the extended graduation for VB2-100-EC
0 all versions
1
2 (only for VB2-100-EC and for
batching Scales)
A10
Auto Power Off
Period
Selects the auto power off time period in minutes: “Off” = Disabled (Always
ON)
1, 2, 4, 10, 20,60, off All
versions factory default is 10
Calibration
Hantverksvägen 15,
76493 Väddö, Sweden. [email protected]
www.vetek.com

page 5
Tel [phone]
We recommend the scale to be calibrated at yearly intervals.
The minimum test weight that can be used is 70% of full-scale capacity.
To adjust the zero point using the F16 zero adjust procedure:
1. Turn the power OFF
2. Put Calibration Switch to the Calibration position.
3. Turn the indicator ON.
4. Scroll to "F 16". Use TARE or ON to move up or down.
5. Press ZERO. The display will momentarily show "C 0" followed by a value. (If you want,
press Dot to go back to parameter number.)
6. After making sure that there are no weights on the platform, press ZERO to zero out the
displayed value.
7. Press NET to save the zero point value. The display will show "EndC0"momentarily, and
then revert back up to F16. At this time, proceed to the F17 span calibration to complete
indicator calibration.
To adjust the max point using the F17 span adjusts procedure:
1. Scrollto"F17",thenpressZERO to enter spancalibrationmenu.
2. The display will momentarily show "C 1" for the span calibration, followed by a value with one flashing digit.
This value will be zero. Place the test weight on the Scale.
3. Pressing TARE or ON will change the position of the flashing digit.
4. Increase the flashing digit by pressing Dot. Decrease the flashing digit by pressing ZERO.
5. Aftersettingtheexactvalue,pressNETtosavethevalue.
6. Iftheadjustmentwassuccessful,thedisplaywillshow"EndC1"momentarily,andthenrevertback uptoF17.
"Err0" –Thecalibrationtestweight ortheadjustedkeyed-in weight islarger thanthe fullcapacity
of thescale.Changethecalibrationtestweightorchecktheinputdata.
"Err1" –Changethecalibrationtest weightorchecktheinputdata.
"Err2" –Theinternalresolution ofthescaleisnothighenoughtoacceptthecalibrationvalue.
SelectalargerparameterfortheSpanGain(F2).
7. Put the Calibration Switch to the normal mode.
8. Check the Scale.
Specifications and displayed error codes.
ON
PRINT
NET
GROSS
OFF
ZERO
TARE
Hantverksvägen 15,
76493 Väddö, Sweden. [email protected]
www.vetek.com

page 6
Tel [phone]
General
Model
Capacity /
Graduation
Weight kg
Dimension
mm
Battery
VB2-30-EC
Max 30 kg / 50 g
3,6
210 x 260x 65
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-100-EC
WS-100-EC
Max 100 kg / 50 g
4,5
260 x 345 x 55
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-200-EC
Max 200 kg / 100 g
4,5
260 x 345 x 55
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-30-05
Max 30 kg / 5 g
Not approved version
3,6
210 x 260x 65
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-100-02
Max 100 kg / 2 g
4,5
260 x 345 x 55
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-100-10
Max 100 kg / 10 g
Not approved version
4,5
260 x 345 x 55
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-130-10
WS-130
Max 130 kg / 10 g
Not approved version
4,5
260 x 345 x 55
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-100-50
Max 100 kg / 50 g
Not approved version
4,5
260 x 345 x 55
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
VB2-200-10
Max 200 kg / 20 g
Not approved version
4,5
260 x 345 x 55
6 of alk. 1,5 V batteries LR6/AA for 15 hours
operation.
Alternative power is a 9 VDC adaptor (centre minus).
OPERATOR INTERFACE
Display
0.75" (19 mm) 7-segment, Liquid Crystal, 6-Digit
Additional Symbols
Net, Gross, Stable, Tare, lb, kg, Zero
Keyboard
5-key flat membrane panel
ENVIRONMENTAL
Operating Temperature
0 to +30 grad C (-10 to +40 grad C not approved version)
Storage Temperature
-25 to +70 grad C
Displayed error codes.
CODE
MODE
MEANING / POSSIBLE SOLUTION

Normal Operating
Mode
Gross Overload. A weight greater than the rated capacity has been applied to the scale. Remove
the weight from the platter or try re-calibrating the scale. Otherwise, check for a bad load cell
connection or possible load cell damage due to overloading.
bAtt
Normal Operating
Mode
Indicates a low battery condition. Re-charge the battery or replace if alkaline batteries.
Err 0
Span Calibration
Mode (F17)
Keyed-in weight value is larger than full-scale capacity. Use a smaller test weight or check keyed-
in value.
Err 1
Span Calibration
Mode (F17)
Keyed-in weight value is less than 1% of full-scale capacity. Use a larger test weight or check
keyed-in value.
Err 2
Span Calibration
Mode (F17)
There is not enough load cell signal to produce the internal counts necessary to properly calibrate
the scale. First check all load connections. Use F16 mode to view internal counts. See Appendix C
for more information.
Err 3
All Modes
Non-volatile memory read error. One or more setup parameters have been lost.
Err 4
All Modes
Non-volatile memory writes error. Indicator needs service.
Err 5
Key-in Span
Calibration Mode
(F20)
You have attempted to enter a zero value for C1. Enter a known calibration value greater than
zero.
Err 7
Initialization
No reading from the ADC. Make sure there is a load cell(s) connected to the indicator at start-up.
Err 9
Normal Operating
Span calibration value has been lost. Re-calibrate the Scale.
Fault localization and repair.
Hantverksvägen 15,
76493 Väddö, Sweden. [email protected]
www.vetek.com

page 7
Tel [phone]
Please note: If a verified Scale is repaired it probably needs a new verification, check with authorities
in your country.
Fault localization
If the Weighingblock is “dead”.
1. Change to new alkaline batteries.
2. Change the membrane key buttons if you have reason to believe it’s broken.
IftheScalestartsbutthedisplayshowswrong.
1. AdjustandCalibratetheScale.
2. If it not works, the Scale must be demounted.
Demounting.
1. DemountthebottomplateoftheWeighingblocktroughthetwoscrewscoveredbyapieceoftape.Be
carefulwiththekeyboardconnection.
2. Check the inside of the Scale visually. Look for bad cables and connections.
3. If needed, clean the PC-board.
If the Scale shows F1
1. Probably the Calibration Switch has been changed to calibrationmode?
2. Reset to normal mode.
ChecktheLoadcell
ChecktheLoadcell withauniversalvoltinstrument,seetable.Theleftpinisnumber1.
Terminal
J1
Description
Colours
Loadcell
AG
Colours
Loadcell 1042
Colours
Loadcell LOC o
FAS
Colours
Loadcell
SP4
E+ (1)
Out +5 VDC*
Brown
Green
Red
White
S+ (2)
In +
Yellow
Red
Green
Green
E- (3)
Out 0 VDC
Green
Black
Black
Black
S- (4)
In -
White
White
White
Red
If it is problem to get a reading on the display or it is important to calibrate.
1. Check the excitation voltage (E+ and E-) from the Indicator. Should be 5,0* (+-0,4) VDC.
2. Check the input to the Indicator (S+ and S-). The output from the Loadcell S+ and S- (pin 2
and 4) will increase from aprox. 0 to 10 mV analogue to the capacity range (100 or 30 kg).
Note S+ is plus and S- is minus. The polarity is important.
3. If the input is wrong, <0 mV or > +10 mV with unloaded Scale check the Loadcell. Do have
only E+ and E- connected (or probably an external Power 5 VDC) and checks the output
from the Loadcells direct on the wires. Should be 0 mV to +10 mV depending on the load.
Hantverksvägen 15,
76493 Väddö, Sweden. [email protected]
www.vetek.com

page 8
Tel [phone]
Instruction for handling Weighingblock VB2-series and UNISCALE
This instruction is valid for the new design with waist and rounded corners. Shipped after 2002-09-18 with serial
number higher than 74201
This instruction is for the user of the Scale. It is the last site in the complete manual. Hopefully is this the only
needed information. For complete information, contact you wholesaler, Vetek AB or download it from our web
site http://www.vetek.com
We hardly recommend that the user of this Scale to get a good acknowledge about all rules and the law. To get
complete information we recommend taking a look at the Authorities web sites.
LCD
Enunciator
MEANING
0
Better known as the “Center of Zero” enunciator, this light is active
whenever the displayed weight is within ± 0.25 divisions of true zero.
N
Indicates that the indicator is displaying net weight.
G
Indicates that the indicator is displaying gross weight.
T
Indicates that a tare weight has been established in the system.
lb, kg
Indicates the unit of the displayed weight (normally disabled).
bAtt
Indicates a low battery condition. Re-charge the battery or replace if
alkaline batteries.
Indicates stable weighing.
Enunciator Definitions ShownaboveistheLCDdisplay.Beforereadingthevaluethestableindicatormust be ”on”.
If notwaitafewsecondsuntilitappears.
Handling
1. Press ON to start the scale.
2. If necessary, press ZERO to obtain a weight reading of zero.
3. Press OFF to switch off the scale. Hold 3 seconds.
4. The scale switches off automatically after 10 minutes when not in use
Weighing (e.g. a cylinder with liquid)
1. Unload scale and press ZERO.
2. Place the object (cylinder, container, etc) on the scale’s platter and allow the weight indication to stabilize. If
the item weight exceeds the scale’s weight capacity, it displays “”. Press TARE to zero the
Scale. The display shows zero weight and turns the NET enunciator on.
3. NET/GROSS toggles between Gross and Net weight display only if a Tare has been established.
4. “Dot”. Extended graduation to 10 g for VB2-100-EC when pushed and 5 sec after release.
General advice
When the Scale is not in use and is transported between different working places we recommend to use a
case or any other protection against vibrations and other hard environmental conditions.
Protect the scale with a transparent plastic bag if there is any risk of leakage or when working in a wet
environment.
Use onle 6 pcs alkaline 1,5 V batteries LR6/AA. Alternative power is a 9 VDC adaptor (centre minus).
ON
PRINT
NET
GROSS
OFF
ZERO
TARE
Hantverksvägen 15,
76493 Väddö, Sweden.
[email protected]
www.vetek.com

page 9
Tel [phone]
Communication Port (not valid for UNISCALE)
This instruction is valid for the new design with waist and rounded corners
(for units shipped after 2003-03-01).
This new generation of Weighingblock have a Communication Port as standard. It is possible to connect
different accessories as Printer, PC/Notebook or Solenoid module VBB-10.
Printer for the weight value.
Many printers in the market can be connected e.g. Martels MCP9800. For more information, contact Vetek AB.
PC/Notebook
The Scale can be connected to a PC/Notebook. For more information, contact Vetek AB.
Solenoid module VBB-10 (Note: this function in VB2 is standard for Scales delivered after march 2003)
One time set up: F11 must be “1” and A5 must be “2” (normally done when delivered)
Handling
1. Mount the Solenoid module to the cylinder.
2. Connect the ”zero modem cable” and the Mains cable. (For
the points 3 –10 below it is no need for the Scale to be on the floor, you can keep it in your hands)
3. Start the Scale with ON and wait a few seconds.
4. To set the Batching Weight:
5. Press, ”Dot”, display shows 0,0 (flashing).
6. Press ON until the first relevant digit flash.
7. Change to the wished value with ”Dot”.
8. Press ON until the next relevant digit flash.
9. Change to the wished value with ”Dot”.
10. When the Scale shows wished value, save with NET
11. Press ZERO it the Scale not shows zero and put the object on the Scale. The Scale shows the gross weight.
12. Batching: Press TARE. The Scale shows zero and the valve is opened.
13. When the weight difference on the Scale is same as Batching Weight the valve will close.
14. The Scale shows the Batching Weight. Press NET/GROSS for gross weight.
General advice
Too fast batching gives less accuracy.
Do not touch the tube to the cylinder during batching.
VBB-10 consist of:
VBB-10-10 Box with Solenoid
VBB-10-11 “Zero modem cable” 9-pin female/female
VBB-10-12 Mains cable.
Hantverksvägen 15,
76493 Väddö, Sweden.
[email protected]
www.vetek.com