Vision Fitness X6100 User manual

Assembly
Guide
X6100 AND X6000
FOLDING ELLIPTICAL TRAINERS

5
STEP
1
STEP
4
STEP
3
STEP
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find
your new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12.
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Elliptical Trainer to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
X6100 AND X6000
FOLDING ELLIPTICAL TRAINERS
2
STEP
6
STEP
OPTIONAL

TOOLS & PARTS INCLUDED
17mm Wrench
Screwdriver
5mm L-Shaped Wrench
PARTS BOX
Console Mast Boot, Qty: 1
Dual-Action Link Arm Covers, Qty: 2
Dual-Action Axle Covers, Qty: 2
Child Safety Guard Hardware Package, Qty:1
Rear Stabilizers, Qty: 2
Pedal Support Bracket, Qty: 2
Water Bottle & Cage, Qty: 1
Mounting Support, Qty: 1 (X6000 ONLY)
Power Supply, Qty: 1 (X6100 ONLY)
Tension Knob, Qty: 1 (X6000 ONLY)
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
6mm L-Shaped Wrench
13mm Wrench

ORANGE BAG
PINK BAG
BLACK BAG
GREEN BAG
M8x13L Screw
Quantity: 6
8x35x2T Washer
Quantity: 2
20x29x1.5T Wavy Washer
Quantity: 2
M8 Nut
Quantity: 4
M4x15L PanHead Screw
Quantity: 4
M5x10L Screw
Quantity: 4
M8x20L Screw
Quantity: 2
8x14x1.5T Washer
Quantity: 3
M8x60L Screw
Quantity: 3
5x10x1T Washer
Quantity: 1
X6000 ONLY
M5x70L Screw
Quantity: 1
X6000 ONLY
8x14x1.5T Washer
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
8x16x1.5T Washer
Quantity: 2
M8x30L Screw
Quantity: 2
BLUE BAG
M5x10L Screw
Quantity: 2
8x30x1.5T Washer
Quantity: 2
5x10x1T Washer
Quantity: 2
Rubber Nut Cap
Quantity: 2
5x10x1T Washer
Quantity: 4
Link Arm Sleeve
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
M8x20L Screw
Quantity: 2

5
1
STEP
Guide
Rail
Axle
Stabilizer
1
STEP
• For ease of assembly, place a block
of wood (about 2” thick) under the
rear of the frame.
• Slide the axle through the plastic
sleeves of the right guide rail and the
frame. Slide the left guide rail onto the
left side of the axle.
• Slide the right stabilizer onto the
right side of the axle and the left sta-
bilizer onto the left side of the axle. Fix
each side in place with a washer
(8x14x1.5T) and screw (M8x20L).
Tighten with a 5mm L-shaped wrench.
ORANGE BAG

6
2
STEP
• Slide a wavy washer (25x34x2T)
onto the right rotation axle. Slide the
bushing housing of the right pedal
arm onto the right rotation axle. The
pedal arm roller wheel should be
placed in the groove of the guide rail.
Secure the pedal arm to the rotation
axle with a washer (8x30x1.5T) and
screw (M8x20L). Tighten with a 5mm
L -shaped wrench.
• Place the pedal arm bracket cover
over the bushing housing of the pedal
arm. Secure in place with a washer
(5x10x1T) and screw (M5x10L).
Tighten with the screwdriver.
• Repeat both steps on the left side.
BLUE BAG
2
STEP
Pedal Arm
Bracket Cover
Rotation
Axle
Guide Rail
Pedal Arm

7
3
STEP
• With the screwdriver, remove the
screws for the water bottle cage in the
center of the console mast. Slide the
rubber boot onto the console mast.
• Unfold the wire harness located in
the frame bracket. Wrap the wire tie
around the end of the wire harness.
Pull the wire tie and wire harness up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket. NOTE: For the
X6000, the tension cable should also
run up through the console mast.
• Secure the mast to the frame using
three lock washers (8x14.1.5T) and
three capscrews (M8x60L). Tighten
with the 6mm L-Shaped wrench.
• Slide the rubber boot down the
console mast and snap it in place on
top of the side cover.
X6000 ONLY: Snap the tension knob
mounting support on to the tension
knob. Turn the tension knob to level
16. Attach the knob cable to the ten-
sion cable in the console mast. Secure
the tension knob to the console mast with
the washer (5x10x1T) and screw
(M5x70L). Tighten with the screwdriver.
• Remove the four screws from the
back of the console. Connect the wire
harness to the plug in the back of the
console. Connect the heart rate wires
from the console mast to the console.
Attach the console to the console mast
with the four screws.
• Attach the water bottle cage with
the screwdriver and the screws removed
earlier in this step.
PINK BAG
X6100 X6000
X6000 ONLY
Console
Console
Mast
Mounting
Support
Tension
Knob
Boot
Frame
Bracket

8
4
STEP GREEN BAG
• Slide a wavy washer (20x29x1.5T)
on the lower link arm axle, which is
located under the foot plate. Slide the
axle through the bracket located on top
of the pedal arm.
• Secure the lower link arm to the
pedal arm by attaching the pedal
support bracket with three screws
(M8x13L). Tighten with the 5mm
L-Shaped wrench.
• Repeat this step on opposite side.
4
STEP
Lower
Link Arm

9
5
STEP
• On the right side, slide the dual-
action axle cover into place on the con-
sole mast axle. Slide a wavy washer
(25x34x2T) onto the axle. Slide the
right dual-action arm on the axle. Fix in
place with the washer (8x35x2T) and
locknut (M8). Cover with the included
nut cap.
• Make sure the sleeve is in place in
the socket joint of the lower link arm.
Connect the lower link arm to the dual
action arm with a screw (M8x30L).
Attach the washer (8x16.1.5T) and nut
(M8) to the end of the screw. Tighten
with the 6mm L-Shaped wrench and
13mm wrench.
• Position the link arm cover over the
joint of the lower link arm and secure
the two pieces of the cover together
with a panhead screw (M4x15L).
Connect the cover to each side of the
lower link arm with a washer
(5x10x1T) and screw (M5x10L).
• Repeat these steps on the left side.
BLACK BAG
6
STEP
OPTIONAL
5
STEP
Dual-Action
Axle Cover
Link Arm
Covers
Dual-Action
Arm
6
STEP
• NOTE: Elliptical Trainer cannot be
folded with the child safety guards in
place.
• Line up the grooves on the child
safety guards with the screws on the
guide rails. Slide the safety guard into
place on the guide rails. Tighten the
screws with the screwdriver to
lock in place.
SAFETY GUARDS
OPTIONAL

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2005 Vision Fitness. All Rights Reserved. 1.05 Part #Z60EP32D-AG
AG18.19PRD
REV6
starts
vision
with a
it all
10