Vision Fitness X6200HRC/DA User manual

FITNESS
VISION
Guide
Assembly
MODELS X6200HRC/DA & X6000DA
DUAL-ACTION ELLIPTICAL TRAINERS

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding
though, enter your new Elliptical Trainer’s serial number here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Elliptical Trainer, to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
Before you begin…
dual-action elliptical trainers
5
STEP
1
STEP
3
STEP
4
STEP
X6000DA
X6200HRC/DA
2
STEP

5MM Allen Wrench
13MM Wrench
Screwdriver
5MM L-Shaped Wrench
TOOLS & HARDWARE INCLUDED
M8 x 80MM Bolt
Quantity: 4
M8 x 13MM Nylock Nut
Quantity: 4
M8 x 45MM Bolt
Quantity: 2
BLUE BAG
BLACK BAG
M8 x 16MM Bolt
Quantity: 4
19MM D x 440MM L Rear Folding Axle
Quantity: 1
(not shown to scale)
3

GREEN BAG
M7 x 35MM Bolt
Quantity: 2
M8 x 12MM Bolt
Quantity: 2
M8 x 25 x 1.5T Washer
Quantity: 2
M16 x 22 x .3T Spring Washer
Quantity: 2
M26 x 34 x .3T Spring Washer
Quantity: 2
M8 x 35 x 2T Washer
Quantity: 2
M8 x 13MM Nylock Nut
Quantity: 4
13MM Nut Caps
Quantity: 2
ORANGE BAG
M8 x 16MM Bolt
Quantity: 2
16 x 22 x .3T Spring Washer
Quantity: 2
5/16” x 30 x 1.5T Washer
Quantity: 2
M5 x 25MM Bolt
Quantity: 1
M8 x 60MM Bolt
Quantity: 2
16 x 28 x 1.5T Washer
Quantity: 2
8 x 15 X 2T Lock Washer
Quantity: 4
8 x 17 X 1.5T Washer
Quantity: 2
PINK BAG
M8 x 12MM Bolt
Quantity: 2

5
1
STEP
• Install the left and right stabilizers
with the four bolts (M8 x 16MM), using
the Blue 5MM Allen wrench.
• Cover both stabilizers with the
included rubber boots.
• Insert the rear folding axle shaft
(440MM L x19MM D) into the rear tube.
BLACK BAG 1
STEP
2
STEP
• Slide a spring washer (M16 x .3T)
onto the right-hand side of the rear
folding axle, followed by the right-
hand pedal arm guide rail (the guide
rails each have a blue indicator arrow
printed on their sides; these arrows
should face to the outside).
• Slide a flat washer (M16 x 1.5T)
onto the right-hand side of the rear
axle, followed by a rear wheel.
• Slide the large flat washer
(5/16” x 1.5T) onto the right-hand
side of the rear axle, and secure with
a bolt (M8 x 16MM).
• Repeat above steps to install left-
hand pedal arm guide rail.
ORANGE BAG
2
STEP
3
STEP
3
STEP
• Mount the rear pedal arms to the
front pedal arms using four bolts
(M8 x 80MM) and four 13MM NyLock
nuts, using the 13MM wrench.
• Install the foot toe pieces to the front
pedal arms with two bolts (M8 x 45MM)
using the Blue 5MM Allen wrench.
BLUE BAG