
9
•
Lower the lock (7) and remove the lid (3).
•
For easy removal of the grating filter (4) remove the
grating filter (4) with the juice collector (5) holding the
juice collector (5) and pulling it upwards.
•
Wash thoroughly and dry all the removable parts (1, 3,
4, 5, 10 11) that will contact products.
Note: Be cautious when holding the grating filter (4) in
your hands, as the disc grating surface is very sharp.
MAKING JUICE
Before the first plugging in make sure that
the operating voltage of the unit corresponds to the volt-
age of your mains.
Fruit and vegetables meant for processing must be fresh.
Before juice extracting wash fruit/vegetables, remove ined-
ible parts from vegetables or fruit, such as stems, hard peel
or stones, for example, of cherry or peach, cut them into
pieces easily fitting into the feeding chute (2).
•
Place the motor unit (8) on a dry, flat and steady sur-
face.
•
Before unit assembling make sure that the operation
mode switch is set to the position «0», and the plug is
not inserted into the mains socket.
•
Set the juice collector (5) on the motor unit (8).
•
Install the grating filter (4) into the juice collector (5).
ATTENTION!
Do not use the juice extractor if you find mechanical dam-
ages of the grating filter (4).
•
Set the pulp container (10) on the left side of the juice
extractor.
•
Install the lid (3) on the juice collector (5) and fix it with
the lock (7).
•
Turn the spout (6) to the left until bumping.
•
Set the juice cup (11) under the juice draining spout (6).
•
Insert the power plug into the mains socket. The illu-
mination of the operation mode switch (9) will light up.
•
Switch the juice extractor on by setting the operation
mode switch (9) to the position «1» (low speed) or to
the position «2» (high speed).
Notes:
Low speed «1» is intended for extracting juice from soft
vegetables/fruits, such as tomatoes, ripe pears, strawber-
ries, oranges, plums, grapes, pumpkins, onions, cucum-
bers etc.
High speed «2» is intended for extracting of juice from
hard vegetables/fruits, such as artichoke, carrots, apples,
pepper, beet, potatoes, pineapples, vegetable marrows,
celery, spinach, dill, leek, etc.
ATTENTION!
To avoid the grating filter (4) stopping and motor rotor
jamming during the processing of viscous or quite
hard food it is recommended to use the high speed
operation mode «2» of the juice extractor.
•
The unit will be switched on only if all the removable
parts are installed properly, and the lid (3) is fixed with
the lock (7).
•
Feed fruit/vegetable pieces into the lid (3) feeding
chute (2) only when the grating filter (4) is rotating.
•
Gradually put vegetables or fruits cut beforehand into
the lid (3) feeding chute (2) and push them gently with
the pusher (1). Do not press on the pusher (1) too hard
as it can lead to decrease of juice amount as well as
stop the grating filter (4) rotation. The slower is the
fruit and vegetables processing, the higher is the juice
extraction rate.
•
Do not put your fingers or any other foreign objects into
the lid (3) feeding chute (2).
•
During operation, check the grating filter (4) periodi-
cally for obstruction of the mesh with pulp, if necessary
wash the grating filter (4); before removing the grating
filter, switch the juice extractor off and unplug it.
•
Control the pulp container (10) filling, if the container
(10) is filled up, switch the juice extractor off, unplug it
and remove the pulp from the container.
Note: - during the breaks between operation or after filling
the juice cup (11) turn the spout (6) to the right until bump-
ing, the juice will not drip on the table.
ATTENTION!
The maximal allowable continuous operation time of
the juice extractor is not more than 1 minute with sub-
sequent break of at least 1 minute. After three opera-
tion cycles,
take at least 15-minute break.
After processing of 500 g of hard and fibrous products
(citrus plants, pineapples, apples, carrots, etc.) dis-
assemble and clean the unit. Non-compliance with the
requirement can cause the grating mesh blockage and
will complicate the unit cleaning.
•
After unit operation, switch it off by setting the switch
(9) to the position «0», and unplug it.
OVERHEATING PROTECTION
Overheating protection switches the electric motor off if the
operation temperature of the electric motor is exceeded.
If the juice extractor switched off during the operation,
set the operation mode switch (9) to the position «0» and
unplug the unit. Let the unit cool down for 30-40 minutes
and switch it on again. Do not exceed the specified opera-
tion time and do not overload the juice extractor with prod-
ucts during its operation.
CLEANING AND CARE
After the end of operation or before cleaning always switch
the unit off and unplug it.
Disassemble and clean the juice extractor after every
usage and follow the recommendations below.
•
Remove the pusher (1) from the lid (3) feeding chute (2).
•
Lower the lock (7) and remove the lid (3).
•
For easy removal of the grating filter (4) remove the
grating filter with the juice collector (5) holding the
juice collector (5) and pulling it upwards.
•
Set the spout (6) to the middle position and remove it.
•
It is recommended to wash all removable parts in warm
water with a neutral detergent right after the unit oper-
ation.
•
It is more convenient to wash the grating filter (4) open-
ings from the outside using an appropriate brush.
•
Be cautious when washing the grating filter (4), the
disc grating surface is very sharp.
•
Do not wash the grating filter (4) and other removable
parts in a dishwasher.