Vivo DESK-M051CW User manual

White Compact Crank Height Adjustable Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-m051cb
SKU: DESK-M051CW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or
inappropriate use.
WARNING!
TOOLS NEEDED
Phillips
Screwdriver
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
154lbs
70kg
Level
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Telescopic
Crossbar
B (x2)
Side Bracket
D (x1)
Right Liing
Column
E (x1)
Sync Rod
S-A (x6)
M6x12
S-C (x10)
3/4” Screw
C (x1)
Le Liing
Column
S-B (x8)
M6x16
Drill
F (x2)
Foot
G (x1)
Crank
S-D (x1)
Allen Wrench

3
STEP 2
Loosen the pre-installed bolts on the le and right legs (C, D). Slide the legs into the ends of the
telescopic crossbar (A), install an M6x12 bolt (S-A) to secure each leg to the crossbar, then tighten all
bolts using the Allen wrench (S-D).
ASSEMBLY STEPS
STEP 1
Loosen the two set screws on the telescopic crossbar (A) using the Allen wrench (S-D) and slightly
extend the crossbar.

4
STEP 3
Assemble the side brackets (B) to the legs (C, D) using x4 M6x12 bolts (S-A) and tighten with the
Allen wrench (S-D).
STEP 4
Adjust the frame length to suit the desktop, making sure the distance between the edge and side
bracket is no more than 2.75” (70mm). Tighten the set screws with the Allen wrench (S-D).

5
STEP 5
Loosen the knobs on the sync rod (E) and extend the hex shas into the legs. Retighten the knobs,
then insert the crank (G) into the leg on either side.
STEP 6
Drill 3/8” (10mm) deep pilot holes using a 3/32” (or 3mm) drill bit. Secure the frame to the desktop
using 3/4” screws (S-C) with a Phillips screwdriver.

6
3
STEP 7
Assemble the feet (F) to the columns using M6x16 bolts (S-B) and the Allen wrench (S-D).
STEP 8
Carefully turn the desk right-side up and adjust foot pads to level if necessary. Turn the crank to raise or
lower the desk. Remove the crank and insert into one of the hex-shape holes in the side brackets (B) to
store.

7
3
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk weight limit. Keep area of vertical motion free of
obstacles.
Keep weight on desk balanced for
correct operation and longer life of
components.
Leave enough slack in cables to
allow for full range of vertical
motion.

LAST UPDATED: 10/25/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303