Vivo DESK-V101MW User manual

Crank Height Adjustable Desk Frame - White
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v101mw
SKU: DESK-V101MW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or
inappropriate use.
PACKAGE CONTENTS
WARNING!
A (x1)
Telescopic
Crossbar
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
154lbs
70kg
B (x1)
Sync Rod
D (x2)
Foot
E (x1)
Drive Rod Module
F (x1)
Leg
C (x2)
Side Bracket
G (x1)
Leg with Gearbox
Level
Drill
S-A (x16)
M6x12 Screw
S-B (x4)
3/4” Screw
S-C (x10)
7/8” Screw
S-D (x1)
Allen Wrench
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
STEP 2
Attach the side brackets (C) to both ends of the frame using four M6x12mm bolts (S-A). Tighten with
the Allen wrench (S-D). Place frame upside down on desktop and drill pilot holes for screws. Use a
3/32” or 3mm bit, and drill holes to a depth of 3/8” (10mm).
ASSEMBLY STEPS
STEP 1
Loosen the two set screws on the telescopic crossbar
(A) using the Allen wrench (S-D). Adjust the crossbar
length to suit the desktop. Attach the telescopic
crossbar to the legs (F, G) as shown using M6x12mm
bolts (S-A),and tighten with the Allen wrench (S-D).
Retighten set screws.
A
c
d
pJ^
pJ^
`
S-A
C
F
S-A
G

4
STEP 3
Place the feet (D) on the legs as shown. Insert and tighten bolts (S-A) using the Allen wrench (S-D).
pJ^
a
S-A
S-A
D
t (x1)
Base

5
STEP 4
Position the frame upright. Loosen the knobs on the sync rod (B) and extend the hex sha. Insert hex
sha into the leg (F), then while holding the hex sha with one hand, extend sync rod onto the sha of
the leg with gearbox (G). Tighten both knobs.
CAUTION: To avoid injury, at least two people should turn the frame upright.
_
knob
NO P
B
123

6
STEP 5
Insert the Drive Rod Module (E) into the
gearbox as shown, and using the module
support plate, mark drilling locations with
a pencil. Drill 3/8” (10mm) deep pilot holes
under the desktop with a 5/64” (or 2mm) drill
bit. Secure the support plate to the underside
of the desk using 3/4” screws (S-B).
If necessary, adjust foot pads to level desk.
E
pJ_
S-B
pJ`
S-C
E
If you are using a VIVO desktop, Refer to the
manual that came with your desktop.
If you are not using a VIVO desktop, place the
desktop on the frame, and secure the desktop
using the ⅞” screws (S-C).

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk weight limit. Keep area of vertical motion free of
obstacles.
Keep weight on desk balanced for
correct operation and longer life of
components.
Leave enough slack in cables to
allow for full range of vertical
motion.

LAST UPDATED: 08/19/2020
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303