Vivo MOUNT-M-FD37 User manual

Manual Ceiling TV Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-m-fd37
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: MOUNT-M-FD37

2 3
ASSEMBLY STEPS
STEP 1
Remove two bolts from mount (A) with 4mm Allen wrench (B) as shown in diagram. Separate VESA
plate from mount.
PACKAGE CONTENTS
TOOLS NEEDED 44lbs
(19.96kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Mount
B(x1)
4mm Allen Wrench
C(x1)
5mm Allen Wrench
W-A (x4)
Screw
M-A (x4)
M4x14
M-B (x4)
M5x14
M-C (x4)
M6x14
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x2)
Washer
W-B (x4)
Anchor
Push arm against ceiling plate of mount (A) to release lock and pull the arm down.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 1-800-371-5654.
STEP 2
M-D(x4)
M8x20
M-E (x4)
D5 Washer
M-F (x4)
D8 Washer
M-G (x8)
Spacer
Drill
Pencil
B

4 5
STEP 3 STEP 4
Mount detached VESA plate to TV with screws (M-A, M-B, M-C, or M-D), washers (M-E or M-F) and
spacers (M-G) depending on your TV’s needs as shown in diagrams.
OPTION A: Wood Wall
Hold mount (A) to mounting surface and mark drill holes with pencil. Drill 2.2” (55mm) deep holes
using a 3/16” (4.5mm) drill bit. Insert screws (W-A) into front two holes, leaving 3mm of thread
exposed. Slide mount onto front two screws. Insert screws (W-A) with washer (W-C) into back two
holes. Tighten all screws.
OPTION B: Concrete/Brick Wall
Hold mount (A) to mounting surface and mark drill holes with pencil. Drill 2.4” (60mm) deep holes
using a 3/8” (10mm) drill bit. Insert anchors (W-B). Insert screws (W-A) into front two holes, leaving
3mm of thread exposed. Slide mount onto front two screws. Insert screws (W-A) with washer (W-C)
into back two holes. Tighten all screws.
STEP 5
Slide VESA plate into mount (A).
W- C
W- A
W- A
W- B
W- A
W- C
W- A
M-A/M-B/M-C/M- D
M- E
M- F
M- D
M- F
M- G
M- F
M- G
M- D

6 7
STEP 5 (Continued)
Replace previously removed bolts and tighten with 4mm Allen wrench (B).
Adjust as Desired
STEP 6
Adjust swivel hinge by removing plastic caps and turning bolts underneath with 6mm Allen wrench
(C). Adjust TV height by loosening bolts with 4mm Allen wrench (B), then tighten at desired height.
B
0°/-9 0°
B

Last Updated: 10/24/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654