Vivo MOUNT-E-FD70 User manual

Electric Flip Down Ceiling TV Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-e-fd70
SKU: MOUNT-E-FD70
[email protected]om www.vivo-us.com 309-278-5303

2
PACKAGE CONTENTS
WARNING!
A (x1)
Mount
B(x1)
Center Plate
C(x1)
Ceiling
Template
M-F (x4)
Square Washer
M-G x8)
5mm Spacer
M-H (x8)
15mm Spacer
W-A (x6)
Bolt
M-E (x4)
M8x50
M-A (x4)
M5x14
M-B (x4)
M6x14
M-C (x4)
M6x30
M-D (x4)
M8x30
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician.
Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use
this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x4)
Washer
W-B (x6)
Anchor
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-5303.
D(x2)
Decorative Cover
E(x2)
VESA Bracket
F (x2)
Bracket Rail
G(x1)
Power Adapter
H(x1)
Remote
Control
I(x4)
Cable Tie
77lbs
(35kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver
Drill Pencil
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
J(x2)
Leveling Knob
K (x4)
Set Screw
L(x4)
Philips Head Bolt
M(x4)
Washer
N(x4)
Hex Nut
O(x4)
Hex Socket Head
Bolt
P (x1)
Allen Wrench

3
ASSEMBLY STEPS
STEP 1
OPTION A: Wood Ceiling
Using ceiling template (C), mark exact location of
mounting holes. Drill pilot holes 2.2” (55mm) deep
using a 3/16” (4.5mm) drill bit. Insert two screws
(W-A), leaving a 0.2” (5mm) gap from ceiling.
Hang the ceiling mount so that the screws fit
into the keyhole openings. Slide mount forward,
then secure using additional screws (W-A) with
washers (W-C). Tighten all screws.
OPTION B: Concrete Ceiling
Using ceiling template (C), mark exact location
of mounting holes. Drill pilot holes 2.4” (60mm)
deep, using a 3/8” (10mm) drill bit. Insert six
concrete anchors (W-B), then tighten two screws
(W-A), leaving a 0.2” (5mm) gap from ceiling. Hang
the ceiling mount so that the screws fit into the
keyhole openings. Slide mount forward, then
secure using additional screws (W-A) with washers
(W-C). Tighten all screws.
NOTE: If mounting to a wood beam ceiling,
ensure the front and back holes are used for
the main support if mount is in line with the
beam. If perpendicular to the beam, use keyhole
openings for the main support. Do NOT use
included concrete anchors (W-B) for wood or
drywall.
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.

4
STEP 2
Assemble the bracket rails (F) to the center plate (B) using Phillips head bolts (L),
washers (M) and hex nuts (N). Tighten with a Phillips screwdriver while holding nuts
with a wrench. Slide VESA brackets (E) onto the rails as shown and insert hex socket
head bolts (O) into the rails using the Allen wrench (P).
STEP 3
OPTION A: Flat Back TV
Align the VESA bracket assembly with the mounting holes in the back of the TV screen.
Install assembly to TV using appropriate screws (M-A, M-B) and square washers (M-F)
according to your screen’s requirements.
Adjust VESA bracket spacing to match TV
mounting holes, and lock in place using
the set screws (K) with the Allen wrench
(P). Remove x4 pre-installed screws from
the center plate, and loosen the center
screw until 5mm of thread is exposed.

5
STEP 3 (Continued)
OPTION B: Curved/Recessed Back TV
Align the VESA bracket assembly with the mounting holes in the back of the TV screen.
Install assembly to TV using appropriate screws (M-C, M-D, M-E), square washers (M-F) and
spacers (M-G, M-H) according to your screen’s requirements.
STEP 5
Place the TV with VESA bracket assembly on the ceiling mount arm (A) by inserting the
center screw into the keyhole at the desired height. Secure using previously removed
screws (from end of step 2) and tighten with a Phillips screwdriver. Clearance between the
ceiling and top edge of TV should be no less than 15mm when TV is in the fully lowered
position.
STEP 4 (Optional)
Attach the leveling knobs (J) to the lower two set screws (K) as shown. This will ensure the TV is
perfectly level with the ceiling when raised.

6
STEP 6
Run cables along edge of mount. Allow slack in cables for arm movement. Place decorative covers (D)
over cables and snap into place.
Using cable ties (I), fasten cables to the side of the arm.
NOTE: Keep cables clear from inside of arm to avoid damage due to pinching.

7
STEP 7
Plug power adapter (G) into mount, and connect to AC outlet.
NOTE: Plugging power supply into AC outlet prior to the mount may
cause a large spark when connecting to the mount.

LAST UPDATED: 11/29/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M