VOLYA DACHNAYA STRELKA-3 Programming manual

any length multipple to 2m
width 3,0 m
height 2,4 m
CLASS
«TITANIC STRENGTH»
Quality management system (QMS)
of LLC «Volya» is certied
for compliance with
standard of
ISO 9001:2008
Certied by
Russian Registry
DACHNAYA STRELKA-3
Cellular polycarbonate greenhouse
(EURO)
Technical certicate
Assembling manual
page 2-5
page 6-27

2
Technical certificateTechnical certificate
Table 4 Detailed list of parts for Dachnaya-Strelka-3 greenhouse
№
marking name quantity, pcs
Box №1
1 4н lower arch 6
2 4в upper arch 6
3 8 upper door opening stand 4
4 12 door vertical part 4
5 - profile L=1,05 m 4
Box №2
1 1 stand 10
2 3 support 10
3 5 butt end upper strainer 2
4 6 butt end lower strainer 2
5 6к butt end lower strainer 4
6 7 lower door opening stand 4
7 9 horizontal strainer 1
8 10 side brace 4
9 11 brace spreader 2
10 13 door horizontal part 6
11 16 butt end strap 2
12 17 door strap for the latch 4
13 18 reinforcement nogging piece 2
14 21 middle strainer 4
15 - end reinforcement 4
16 - ridge profile 2
17 - hinge strip L=3,6 m 1
18 - roor strip L=10 m 1
19 - butt end strip L=6 m 2
20 - angle 16
21 - ridge cover plate 3
22 - arm 12
23 - support hook М4х10 8
24 - screw М5х10 372
25 - screw М5х14 22
26 - screw М5х35 120
27 - screw М4х35 8
28 - bolt М5х50 12
29 - bolt М6х60 6
30 - self-tapping screw 6
31 - nut M4 16
32 - nut M5 526
33 - nut М6 6
34 - washer 132
35 - washer 6 12
36 - top wire bandage 3
37 - bottom wire bandage 6
38 - hinges 8
39 -
semifinished rotator (with two elastic headers) 4
40 - bending tube 1
41 - adhesive tape 1
42 - handle 8
43 - pin 4
44 - two-side adhesive tape L=5 m 1
Box №3
1 2 beam 20
2 14 door diagonal part 4
3 15 door diagonal strap 4
4 19 ventilating window horizontal part 4
5 20 ventilating window vertical part 4
6 - hooks 4
3
Perform installation and operation of the greenhouse in strict accordance
with the manual and operating rules stated in the technical certificate.
Please keep this technical certificate for further reference.
Description
DACHNAYA STRELKA-3 greenhouse is designed for creation of microclimate
favorable for growing garden crops on cottage and household plots. Area of covered
soil depends on length of the greenhouse (table 1). Height of installed frame is 2.4
m, width is 3.0 m. The greenhouse may have various length depending on desire of
buyer. Required length of greenhouse is provided by purchase of additional Vstavka
packages adding 2 m to the base length (table 2).
Greehouse specifcations
Chart 1
Table 3 Box contents
contents dimensions, mm
weight
max, kg
Frame (base length 2 m)
Box №1– manual, parts of arches and butt ends, prole 70x270x1560 21,0
Box №2
– straight parts for butt ends, arch reinforcements,
ridge prole,weather strips beams, fasteners and parts,
bandage
60x370x1245 33,0
Box №3 - straight parts and assembly 70x110x1000 20,0
Insert (extending the frame by 2 m)
Box №1 – beams, parts of arches and straight parts, ridge
prole, fasteners and parts 70x270x1560 36,0
Chart 2 Box supplied
Table 1 Parameters of greenhouse
length, m covered area, m2Polycarbonate sheets 2100 x 6000, pcs
2 6 2
412 3
618 4
824 5
Table 2 Box completing
greenhouse
length, m box №1 box №2 box №3 box insert
2 + + +
4+ + + +
6+ + + ++
8+ + + +++
The greenhouse frame is made of zinc-coated iron and assembled with screws and
nuts. The greenhouse is fixed to the ground by digging special supports into the soil or
by joining it to a foundation slab with fastening hooks. The supply package includes
everything you need for fastening the cover surfaces. Cover surface sheets are
supplied following the customer’s request. The greenhouse has two door openings
and two ventilating windows in the opposite ends. Side ventilating windows are
supplied following the customer’s request.

5
4
Technical certificate
Table 5 Detailed list of parts for extension
№ marking name quantity, pcs
Box №1
1 2 balk 20
2 3
support 4
3 1
stand 4
4 4н bottom arc 4
5 4в top arc 4
6 9 horizontal strainer 2
7 10 side brace 8
8 11 brace strut liner 4
9 18 stiffening boom 4
10 - ridge profile 2
11 -
ridge cover plate 2
12 - bottom wire bandage 4
13 - top wire bandage 2
14 - screw M5x10 172
15 - screw M5x14 4
16 - screw M5x35 16
17 - screw M4x10 4
18 - screw M4x35 8
19 - nutM4 12
20 - nut M5 192
21 - nut M6 4
22 - washer 16
23 - washer 6 8
24 - boltМ6х60 4
25 - profile L=1,0 m 4
26 - double sided tape L=5 m 1
Technical certificate
1. Before use of greenhouse,
assembleand install it in accordance
with the manual.
When installing the greenhouse by
third parties, buyer should supervise
compliance of installation with the
manual
Operating rules
2. In winter, coverage of
greenhouseshould not be removed
provided that snow load is limited.
Should greenhouse be unattended all
winter period, buyer should either remove
the coverage or estimate possible
snow load. Ultimate load for the frame
having complete package with installed
drawbars and side braces appears
under 360 kg snow cover per 1 m2 of
horizontal ground surface corresponding
to 1.8 m fresh snow layer or 0.9 m
packed snow layer. Recommended 4
mm depth of polycarbonate is enough
for Russian midland. In case of regions
with snow cover exceeding 0.6 m,
Do not install greenhouse close
to buildings and trees from which
snow or ice can fall down. Minimal
2 m distance is recommended
thicker polycarbonate should be used
for coverage of greenhouse top in
accordance with local conditions.
Maximum wind pressure for this
greenhouse is 25m/sec
Cleaning and washing sheets of polycarbonate.
1. Rinse the sheet with warm water.
2. Wash the sheet with a solution of soft soap or with a domestic detergent and warm
water, using a soft rag or a sponge to take away the dirt.
3. Rinse with cold water and dry with a soft rage to take away the water.
By disinfection of the greenhouse from fungus and biological diseases
pathogens do not use “sulphuric sticks”
When cleaning polycarbonate sheets never use abrasives or high-
alkali cleaning compositions. Dry wiping of the surface can damage the
protective layer and reduce its life cycle. Never use brushes, gauze fabric
or other abrasive materials to wipe the surface of polycarbonate sheets

7
6
Technical certificate Manual
Warranty responsibility
1. The manufacturer shall be responsible for the complete set of parts for
the greenhouse frame.
2. The manufacturer shall be responsible for assemblability of the
greenhouse in accordance with the manual.
3. The manufacturer shall be responsible for the greenhouse endurance in
the specified weather conditions.
4. Time period for making claims is 24 months after the day of purchase.
Warranty provisions
Warranty responsibility shall not cover the following cases:
1. Installation of the greenhouse in violation of the manual provisions.
2. Violation of operation rules.
3. Unintended use of the greenhouse.
4. Deformation of the greenhouse due to soil movement.
5. Floods, hurricanes and other natural disasters.
Manufacturer: LLC Volia
141983, city of Dubna, Moscow Region, 8 Severny Lane.
The manufacturer shall be responsible for the quality
of products in accordance with the Civil Code of the Russian Federation.
The manufacturer shall retain the right
to make changes to the greenhouse design.
Production date:
Warranty responsibility Installation manual for Dachnaya-Strelka-3 greenhouse
1. General view of the frame is given in Picture 1. Parts should be installed in
such a way that side selves of the profile are facing the surface cover. The frame is
assembled of numbered parts.
2. Symbols:
-arrow shows the direction of
installation as per schemes in the
manual.
3. Parts are fastened by putting profiles together and fastening them with screws
and nuts through the holes. When joining parts in “profile-to-profile” way it does not
matter which of the joined parts is above.
4. When assembling be careful not to damage the parts as they do not have sufficient
endurance before the whole structure is assembled. Use supports (e.g. chairs) at
interim stages of assembly to make sure the frame is lifted steadily and evenly. To
make sure holes coincide when assembling complicated joints, use a 5 mm thick nail
or a cone-shaped hand-punch.
Some parts may have spare
holes which are there due to
uniformity of parts
introduction
Be careful when assembling the greenhouse! Parts have sharp
edges. Beware of cuts! Perform all works in protective gloves
When assembling the frame parts should be joined through all
holes as prescribed. A simplified fastening of parts with only one
or two screws is the violation of assembly rules and the ground to
relieve the manufacturer of the warranty responsibility

9
8
Manual
General view of DACHNAYA-STRELKA-3 greenhouse frame
B (inside view)А (outside view)
4В
angle
angle
4В
2 2
4Н
6к 2
1
arm
4Н
Manual
General view of DACHNAYA-STRELKA-3 greenhouse frame
F (outside view)
4В
5
arm
7
1
6к
6
C (inside view)
4Н
2
3
1
Pic. 1
D (outside view) E (inside view)
Dachnaya-Strelka-3
extended by any number of
inserts.
Pic. 2
Pic. 3
858
4060
1000100010001000
3000
Greenhouse foundation support
layout plan.
Pic. 4
А
E
C
B
F
D
1071
arm
2
2
22
2
2
2
2
2
2
2
2
4в
4н
4н
4в
8
8
5
6к
6
77
6к
10
10
10
21
18
18
9
9
9
18
5
21
11
11
3
3
1
1
60
21
ridge
cover
General view of insert
for Dachnaya Strelka-3
greenhouse.
Each insert extends
greenhouse length by 2 m.

11
10
Assemble arcs 4в in pairs using ridge cover
plate and strainer 9. Connect end elements
5 to arcs 4в using arm.
Connect balks 2 to
assembled arcs.
2
2
4в
Assembling stages
Pic. 5
Pic.6
4. Level the frame using filling or deepening of pits to make longitudinal elements
straight, horizontal and parallel to each other and to make arcs even at side view. If arc
planes require leveling, loosen connections of balks with arcs, complete leveling on the
ground and tight screws again. Fill frame supports with soil after fastening bottom wire
bandages on element 3 (Pic.10)
1. Perform the installation close to location of the greenhouse.
2. Install greenhouse in accordance with photographs of installation stages and
units represented in Pic. 5…12. The figures show installation of greenhouse of 4 m
length. Required length is reached using attachment of appropriate number of Insert
packages. Use M5x10 screws for connection of elements.
3. Dig pits on the site selected for greenhouse installation at a depth of shovel blade
according to Pic. 4 Install frame into the pits. Check equality of frame diagonals using
a cord. Total draft of greenhouse into the ground should be so that bottom elements 6
of door opening touch the ground. Check equality of the diagonals using a cord again
and correct position of the frame angles.
Installation sequence
When installing the greenhouse
through digging (without
foundation), connect elements
1 and 3 to the frame. Fasten
bottom wire bandage in free
hole of element 3. Install end
elements 6, 6к, 7, 8, 21.
Pic.10
2
6к
4н
2
1
arm
6к
Pic. 7
Connect arcs 4н to arcs
4в from one side of
greenhouse.
Connect balks 2 to arcs
4н
Pic.9
Connect arcs 4н and
balks 2 from the other
side of reenhouse in the
same way.
Assembling stages
4в
5
5
5
2
2
2
2
2
2
2
2
2
2
2
2
arm
Manual Manual
4н
4н
4в
4в
4в
4в
4в
4н
4н
4н
4н
4н
4н
4н
4н
4н
4н 4н 4н 4н 4н
4в
(inside view) (outside view)
arm
Pic. 8
ridge cover
plate
4в
4в 4в
4в 4в 4в
4в
4в
4в
4в
4в
Б
4в
9
999
4н
2
2
4н 2
2
2
6к
8
21
21
8
7
7
66к 3
1
222
2
2
2
А
B
АB-1, B-2
C
А
А А
B
C
3
1
3
1
bottom wire
bandage
bottom wire
bandage
B-1 B-2
adhesive tape
screw
М5х10
screw
М4х10

13
12
Install side braces 10 on each arc inside of greenhouse frame. Assemble side brace
assembled from two elements 10. Mount side brace liner 11 on the joint of elements
10 and connect it to arc 4н.
Door
9
9
18
18
10
4в
10
2
2
Assembling stages
Manual Manual
Assembled door and end small window
Assemble door and end
small window from
elements 12, 13, 14, 15
(Pic.12)
4н
4в
14
14
14
12
12
12 12
12
13
15
15
15
15
19
19
20 20
14
15
B
Pic. 12
А
12
13
14
13
13
13
13
15
14
14
14
12
13
Small window
Pic. 11
G
F
А
B
CD
11
10
10
4н
19
20
А
А
D
GF
B
B
C

15
14
6000
Door
lower band
Door
small
window
Left end
side
Left end
side
/template/
Right end
side
Right end
side
14901940
2100
1110
800
800
310310
Cutting line
Ridge
panel
Ridge
panel
Manual Manual
Cutting and fastening of coverage
1. Cut a sheet for end coverage. To do this, cut a piece from polycarbonate sheet
(see cutting lines on Pic.13а or Pic. 13b). To make a stencil of coverage, put the cut
piece to assembled end of greenhouse and, without removal of protective film from
polycarbonate, deposit stencil marking on the coverage sheet by elements 4н and
4в (with allowance Pic.14) . When marking a sheet, align its edge strictly with edges
Attention! Coverage sheet side edge is aligned by elements 7, 8, and top
edge on 30 mm above bottom edge of element 5. Mark by elements 4н and
4в with allowance
Mount cellular polycarbonate strictly facing sun with a side having
protective layer (by all means, clarify it under purchase or before
mounting). Protective layer usually is on the side with inscriptions on
transport film. On the other side of sheet film is clear. After marking
the sheet but before its cutting make marks on protective side of each
piece of sheet: after removal of transport film sheet sides have no visual
differences. Transport film is removed from both sides immediately
before fastening coverage on the frame
CUT POLYCARBONATE SHEET STRICTLY IN ACCORDANCE WITH
Pic. 13(а) or 13(b) and Pic. 14
2100 x 600 mm cellular polycarbonate sheet
Pic. 13а
Vertical position of cellular on ridge
pane
Pic. 13b
Horizontal position of cellular on ridge
panel
Pic. 14
8
5
2
4в
coverage
marking
2100
30 mm
marking
- points for mounting of
armsfor coverage fastening
angle
1940
1940
of elements 7 and 8, and top edge at 30 mm above bottom edge of element 5. Cut
a stencil. Mark the rest of sheet using the stencil in accordance with cutting scheme
Pic.13а or Pic 13b.
Cutting lineCutting line
A power jigsaw or fine tooth
arm saw is recommended
for cutting
Warning! When cutting the surface cover in windy weather, fix the edges of
polycarbonate sheets with a load.
Left end
side
Left end
side
Door
Door
Right
end
side
Right end
side
/template/
small
window
small
window
small
window

17
16
hinge
Manual Manual
Раскрой и крепление покрытия торца Cutting and fastening of coverage
Pic. 15
2. Cut ridge coverage pieces located above the door at
the place of installation from remaining pieces. Mark
marking 4в coverage by elements 4в with allowance
aligning bottom edge of the sheet with bottom edge of
element 5 (Pic.15).
marking 4в
5
Cutting and fastening of coverage
Pic.19
adhesive
tape
door sealer
door sealer
hinge sealer
hinge sealer
сoverage
сoverage
сoverage
17
screw
М5х14
handle
handle
сoverage
adhesive
tape
door sealer
hinge
adhesive
tape
door sealer
hinge sealer сoverage
door sealer
door sealer
сoverage
hinge
hinge
adhesive
tape
adhesive
tape
сoverage
Avoid over-tightening screws that fasten the polycarbonate in order
not to damage the polycarbonate sheet and destroy its structure
Pic.16
3. Mount side pieces of coverage in accordance with
Pic.16. Holding a piece of coverage, fasten it with
screws and washers by elements 6к, 7, 8, 21 and by
angles using tap screws with washers. Holes for screws
are drilled by boring bit of 5 mm diameter from inside
of greenhouse through holes in frame elements. Mount
top pieces of coverage fastening them on angles with
washers and tap screws. Cut overlapping with side
pieces.
4. Even coverage pieces by arcs 4н and 4в using a knife
and mount sealing profile in accordance with Pic.17.
5. Fasten pieces of coverage on door with washers
(Pic.18,19). Fasten pieces of coverage on door with
washers (Pic.23), closing cellular beforehand (with
adhesive tape). Mount sealing profiles along the door
contour in accordance with Pic. 19,21,22.
Pic.17
Pic.18
details
4В, 4Н
and 1
end sealing
сoverage
Washer
screw М5х35
Protective layer
angle
washer
washer
end
сoverage
Protective layer
pin

19
18
Manual
Cutting and fastening of coverage
Manual
Cutting and fastening of coverage
8. The washers and the hooks on the end install in accordance with Pic.24.
Pic.24
washer
washer
hook
end сoverage
angle
angle
screw М4х10
screw М5х35
The
ground
7. Install assembled doors and
smallwindows on ends mounting sealer
in accordance with Pic.22.
When mounting small windows, prevent
its further slackening. When tightening
the screws, lift the opposite end of small
window to remove screw gaps in the
holes.
Pic.23
end сoverage
20..25mm
(the output of surface contour door)
door
washer
12
8
screw М5х35
screw М5х35
door
сoverage
small
window
сoverage
door
сoverage
ridged
panel
16
16
screw
М5х50
screw
М5х35
5
door sealer
door sealer
door sealer
19
19
13
13
6
small window
Pic.20
end сoverage
screw М5х35
screw М5х10
screw
М5х10
hinge sealer
hinges
washer washer
washer
washer
washer
12
door
Pic.21
6. Mount end cover plate 16 on end coverage and fasten it on element 5 through
coverage (Pic.20 and Pic.24). Joint of end coverage pieces is under element 16.
door sealer
door sealer
screw
М5х35
screw
М5х35
screw
М5х35
screw
М5х35
Pic.22 9. Install end reinforcing element door opening in accordance with Pic.25
Рiс.25
2
8
end reinforcing

Manual Manual
21
20
Cutting and fastening of coverage
Cutting and fastening of coverage
10. Insert wire rotatorfor
door closing in free
holes (against the stop)
through elements 12 and
17 by straight end from
inside (Pic. 26). In this
position,use the tube to
bend linear part by hand
into opposite outside of
the greenhouse direction
(Pic. 27). Set elastic
header on the rotator (Pic.
28). This construction
allows to push the door in
the closed position, being
both outside and inside
the greenhouse.
Pic.26 Pic.27 Pic.28
17
17
bending
tube
bending
tube
handle 12
20
11. Wire rotator for small window locking is mounted like a door rotator.
rotator
12. Cellular polycarbonate shall be installed strictly defined side out (towards the
sun), which has a protective layer. The protective layer is usually at the side with the
inscriptions on the transport film. The film on the other side of sheet is transparent.
After marking the sheet, but prior to its cutting, make a mark on the protected side
of the sheet for each piece: after removal of the transport film sheet sides are not
visually different. The transport film is stripped from both sides immediately before
fixing the cladding on the frame.
Sections of polycarbonate with open
honeycombs should be covered by
adhesive tape.
12000
2000
1000 1054
2100
For Dachnaya-Strelka-3 greenhouse length by 4 m

Manual Manual
23
22
Cutting and fastening of coverage
Cutting and fastening of coverage
х2
M4x25
х2
13.
1000
х1
х2
L=1,05m
Two-side adhesive tape
Before coating it is necessary to cut the outer surface of the upper
polycarbonate sheet for bending on the ridge (middle of sheet)!
The arrow on the details
is directed to the front
side greenhouse
1054
do not fully tighten!

Manual Manual
25
24
14.
х1
Adhesive tape
15.
х4
х4
M4x35
х4
Cutting and fastening of coverage
Cutting and fastening of coverage
1054

Manual Manual
27
26
17. Details of ridge profile are joined in the length with the installation of the threaded
end of the screws out.
screw М5х14
ridge
profile
х1
M6x60
M6
х1
х2
х1
х1
top wire
bandage
M6x60
M6
х1
х2
х1
х1
top wire
bandage
Cutting and fastening of coverage Cutting and fastening of coverage
16.
х1
х2
M4x25
х2
L=1,0m
1000

Manual
28
Manufacturer
LLC Volia, city of Dubna, Moscow Region.
tel/fax: [phone]
www.perchina.ru
e-mail: [email protected]
This manual cannot be reproduced in any form, fully or partially,
without written consent of Volia LLC