Weidmüller IE-SW-BL05-5GT Manual

Gigabit Ethernet Switch – Basic Line
IE-SW-BL05-5GT
Hardware Installation Guide
Third Edition, July 2011
1243380000/02/07.11
Please note:
This document and any further product information - if
available - can be downloaded at the internet link:
http://www.weidmueller.com/downloads
Copyright Notice
Copyright ©2011 Weidmüller Interface GmbH & Co. KG
All rights reserved.
Reproduction without permission is prohibited.

Overview
The IE-SW-BL05-5GT is equipped with 5 Gigabit Ethernet ports, making it an
ideal and economical solution for demanding, high bandwidth Gigabit Ethernet
applications. In addition, the built-in relay warning function alerts system
administrators when power failures or port breaks occur. The switches have
passed a 100% burn-in test to ensure that they fulfill the special needs of
industrial automation control and can be easily installed with DIN-Rail
mounting as well as distribution boxes.
Package Checklist
Your Ethernet Switch is shipped with the following items. If any of these items
is missing or damaged, please contact your Weidmüller customer service for
assistance.
yEthernet Switch
yHardware Installation Guide
Features
High Performance Network Switching Technology
y10/100/1000BaseT(X) (RJ45), auto negotiation speed, F/H duplex mode
yIEEE 802.3/802.3u/802.3ab.
yStore and Forward switching process type, 8K MAC address entries.
Industrial Grade Reliablity
yPower failure, port break alarm by relay output
yRedundant dual 12/24/48VDC power inputs
Rugged Design
yStandard operating temperature range from 0 to 60°C or extended
operating temperature of -40 to 75°C for (-T) models
yIP30, rugged high-strength case
yDIN-Rail or panel mounting ability
- 2 -

Panel Layout of
IE-SW-BL05-5GT
1. Grounding screw
2. Terminal block for power input
(PWR1, PWR2) and relay output
3. Power input PWR1 LED
4. Power input PWR2 LED
5. Fault LED
6. TP port’s 10/10/1000 Mbps LED
7. Port number
8. 10/100/1000BaseT(X) Port
9. Article Number
10. DIP switches
11. Heat dissipation orifices
12. Screw hole for wall mounting kit
13. DIN-Rail Kit
- 3 -

Mounting Dimensions (unit = mm)
DIN-Rail Mounting
The aluminum DIN-rail attachment plate should already be fixed to the back
panel of the Ethernet Switch when you take it out of the box. If you need to
reattach the DIN-rail attachment plate, make sure the stiff metal spring is
situated towards the top, as shown in the figures below.
STEP 1:
Insert the top of the DIN-rail into the
slot just below the stiff metal spring.
STEP 2:
The DIN-rail attachment unit will
snap into place as shown below.
metal
spring
DIN-Rail
metal
spring
DIN-Rail
To remove the DIN-rail from the Ethernet Switch, simply reverse Steps 1 and
2.
Wall Mounting (optional)
For some applications, you will find it convenient to mount the Ethernet
Switch on the wall, as illustrated below.
STEP 1:
Remove the aluminum
DIN-rail attachment plate
from the Ethernet Switch
rear panel, and then attach
the wall mount plates, as
shown in the figure. ⇒
- 4 -

STEP 2:
Mounting the Ethernet S
screws. Use the switch, wit
as a guide to mark the corr
The heads of the screws sho
diameter, and the shafts sh
diameter, as shown in
witch on the wall requires 4
h wall mount plates attached,
ect locations of the 4 screws.
uld be less than 6.0 m
ould be less than 3.5 mm
the figure at the right.
m in
in
6.0 mm
3.5 mm
NOTE Before tightening screws into the wall, make sure the screw head
and shank size are suitable by inserting the screw into one of the
keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2
sliding the wall mount panel between the wall and the scre
STEP 3:
Once the screws are fixed in
mm to allow room for
ws.
insert the four screw
apertures
Ethernet
en the four
the wall,
heads thr
of the key
ough the large parts
hole-shaped
, and then slide the
Switch downwards, ⇒
as indicated. Tight
screws for added stability.
II 3G
ATE
Certificate number DEM
X Information
1. KO 11 ATEX 150192X
2. Ambient range (-40°C ≤Tamb ≤75°C)
3. Certification string (Ex nC nL IIC T4)
4. Standards covered (EN60079-0:2006, EN60079-15:2005)
The conditions of safe usage:
• These products must be mounted in an IP54 enclosure.
• Install in an area of pollution degree 2 or less.
• A 4mm2 conductor must be used when connection to the external
grounding screw is utilized.
• PROVISIO
APPARATU FROM
URBANCES OF
5.
NS SHOULD BE MADE, EXTERNAL TO
S, TO PREVENT THE RATED VOLTAGE
THE
BEING EXCEEDED BY TRANSIENT DIST
MORE THAN 40 %.
- 5 -

Wiring Requirements
WARNING
Safety First!
Turn the power off before disconnecting modules or wires. Th
proper power supply
the voltage of your power
e
voltage is listed on the product label. Check
source to make sure you are using the
correct voltage. Do NOT use a voltage greater than what is
specified on the product label.
These devices must be supplied by an AELV source as defined in
the Low Voltage Directive 2006/95/EC and 2004/108/EC.
WARNING
Safety First!
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Use separate paths to route wiring for power and devices. If power wiring
and de s must cross, make sure the wires are perpendicular
at the intersec
NOTE al or communications wiring and power wiring in
the sam
charac
yYou can use the type of signal tran mine
which h
similar
Keep input wiring and output wiring separated.
stem
G
Gr
ele
gro onnecting devices.
You should also p
y
ay attention to the following items:
vice wiring path
tion point.
: Do not run sign
e wire conduit. To avoid interference, wires with different signal
teristics should be routed separately.
smitted through a wire to deter
wires should be kept separate. The rule of thumb is that wiring wit
electrical characteristics can be bundled together.
y
It is strongly advised that you label wiring for all devices in the sy
when necessary.
y
rounding Ethernet Switch
ounding and wire routing help limit the effects of noise due to
ctromagnetic interference (EMI). Run the ground connection from the
und screw to the grounding surface prior to c
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.
- 6 -

Wiring the Alarm Contact
The Alarm Contact consists of the two middle contacts of the terminal blo
the Ethernet Switch top panel. You may refer to the next section for detaile
instructions on how to connect the wires to the terminal block conne
ck on
d
ctor, and
how to attach the terminal block connector to the terminal block receptor.
In this sec meaning of the two contacts used to connect the
Alarm Con
tion, we explain the
tact.
FAULT: The two m
FAULT
FAULT
Top View
Front View
If neither of these two conditions is satisfied,
iddle contacts of the
6-contact terminal block connector are used to
detect both power faults and port faults. The
two wires attached to the Fault contacts form
an open circuit when:
s lost power from one of
ts.
f
the Fault circuit will be closed.
Wiring the Redu
The top two contacts and the bo
block connector on the Ethernet Switch the Ethernet
Switch DC inputs. Top and fron
are shown here.
1. Ethernet Switch ha
the DC power inpu
OR
2. The PORT ALARM DIP switch for one o
the ports is set to ON, but the port is not
connected properly.
ndant Power Inputs
ttom two contacts of the 6-contact terminal
top panel are used for
t views of one of the terminal block connectors
STEP 1: Insert the negative/positive DC
wires into the V-/V+ terminals.
STEP 2: To keep the DC wir
Top View
Front View
connector prongs into the terminal block
receptor, which is located on Ethernet
Switch top panel.
es from
inal block
connector.
k
pulling loose, use a small flat-blade
screwdriver to tighten the wire-clamp
screws on the front of the term
STEP 3: Insert the plastic terminal bloc
ATTENTION
Before connecting the Ethernet Switch to the DC power inputs,
make sure the DC power source voltage is stable.
- 7 -

Communication C
IE-SW-BL05-5GT has 5 10/100/10 BaseT(X) Ethernet ports
10/100/1000BaseT(X
Connection
The 10/100/1000BaseT(X) ports lo
used to connect to Ethernet-enabled will choose to
configure these ports for Auto MDI
pinouts are adjusted automatically d
used (straight-through or cross-over
HUB/Switch-type) conne d to the
what follows, we give pinouts for ype) ports and MDI-X
type) ports. We also give cable wiring diagrams for
straight-thr er Ethernet cables.
10 /100Ba
MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45
Pin Signal Pin Signal
onnections
00
) Ethernet Port
cated on Ethernet Switch’s front panel are
evices. Most users
d
/MDI-X mode, in which case the port’s
epending on the type of Ethernet cable
), and the type of device (NIC-type or
port.
both MDI (NIC-t
cte
In
(HUB/Switch-
ough and cross-ov
se T(x) RJ45 Pinouts
1 Tx+ 1 Rx+
2 Tx- 2 Rx-
3 Rx+ 3 Tx+
1 8
6 Rx- 6 Tx-
1000BaseT RJ45 Pinouts
Pin MDI MDI-X
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
1 8
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
- 8 -

RJ45 n) (8 ight-Through Cable Wiring
(8-pi to RJ45 -pin) Stra
Straight-Through Cable
Pin 1
RJ45 Plug
Switch
R
onne RJ45 Connecto
Port
J45
C ctor
r
Tx+
Tx-
Rx+
Rx-
DD+
DD-
DC+
DC-
NIC Port
le Wiring
Cab Rx+
Rx-
Tx+
Tx-
DC+
DC-
DD+
DD-
3
6
1
2
4
5
7
8
3
6
1
2
4
5
7
8
J45 (8-pin) to RJ45 (8-pin) Cross-Over Cable WiringR
Cross-Over Cable
RJ45 Plug Pin 1
Switch Port
(NIC Port)
RJ45
Connector RJ45 Connector
Tx+
Tx-
Rx+
Rx-
(Rx+)
(Rx-)
(Tx+)
(Tx-) DC+
DC-
DD+
DD-
(DD+)
(DD-)
(DC+)
(DC-)
(Tx+)
(Tx-)
(Rx+)
(Rx-)
Switch Port
(NIC Port)
Cable Wiring
Rx+
Rx-
Tx+
Tx- (DC+)
(DC-)
(DD+)
(DD-)
DD+
DD-
DC+
DC-
3
6
1
2
4
5
7
8
1
2
3
6
7
8
4
5
Redundant Power Inputs
Both power inputs can be connected simultaneously to live DC power sources.
If one power source fails, the other live source acts as a backup, and
automatically supplies all of the Ethernet Switch power needs.
Alarm Contact
The Ethernet Switch has one Alarm Contact located on the top panel. For
detailed instructions on how to connect the Alarm Contact power wires to the
two middle contacts of the 6-contact terminal block connector, see the Wiring
be to connect
the Fault circuit to a warning light located in the control room. The light can be
set up to switch on when a fault is detected.
The Alarm Contact has two terminals that form a Fault circuit for connecting to
an alarm system. The two wires attached to the Fault contacts form an open
circuit when (1) Ethernet Switch has lost power from one of the DC power
inputs, or (2) one of the ports, for which the corresponding PORT ALARM
DIP switch is set to ON, is not properly connected.
If neither of these two conditions occurs, the Fault circuit will be closed.
the Alarm Contact section on page 6. A typical scenario would
- 9 -

DIP Switch Settings
1
BSP
2
----
ONOFF
ON DIP
12345
PORT
ALARM
P2
P3
P1
P4
P5
OFF ON
DIP Switch Setting
The default setting for each DIP switch is OFF. The
following table explains the effect of setting the
switches to the ON positions.
Description
DIP
ON Enables broadcast storm protection
BSP OFF Disables broadcast storm protection
ON Enables jumbo frame function
----
refers to Jumbo
Frame OFF Disables jumbo frame function
ON
. If
the port’s link fails, the relay will form an
open circuit and the fault LED will light up.
Enables the corresponding PORT Alarm
PORT Alarm Disables the corresponding PORT Alarm.
y will form a closed circuit and the
D will never light up.
OFF The rela
Fault LE
ATTENTION
To actively update DIP switch settings, power off and then power
on the Ethernet Switch.
- 10 -

LED Indicators
The front panel of the E et Switch contains several LED indicators. The
function of ribed in the table below.
thern
each LED is desc
LED Color State Description
On is being supplied to power input
PWR1
Power
PWR1 AMBER
Off Power is not being supplied to power input
PWR1
On Power is being supplied to power input
PWR2
PWR2 AMBER
Off Power is not being supplied to power input
PWR2
On When the corresponding PORT alarm is
enabled, and the port’s link is inactive.
FAULT RED
Off
When the corresponding PORT alarm is
enabled and the port’s link is active, or
when the corresponding PORT alarm is
disabled.
On TP port’s 10/100 Mbps link is active
Blinking Data is being transmitted at 10/100 Mbps
AMBER
Off TP Port’s 10/100 Mbps link is inactive
On TP port’s 1000 Mbps link is active
Blinking Data is being transmitted at 1000 Mbps
10/100/
1000M
GREEN
Off TP Port’s 1000 Mbps link is inactive
Auto MDI/MDI-X Connection
The Auto MDI/MDI-X function allows users to connect the Ethernet Switch
10/100/1000BaseT(X) ports to any kind of Ethernet device, without paying
attention to the type of Ethernet cable being used for the connection. This
means that you can use either a straight-through cable or cross-over cable to
connect the Ethernet Switch to Ethernet devices.
Triple Speed Functionality and
Switching
The Ethernet Switch 10/100/1000 Mbps RJ45 switched port auto negotiates
with the connected device for the fastest data transmission rate supported by
both devices. The Ethernet Switch is a plug-and-play device, so software
configuration is not required at installation or during maintenance.
The half/full duplex mode for the RJ45 switched ports is user dependent and
changes (by auto-negotiation) to full or half duplex, depending on which
transmission speed is supported by the attached device.
- 11 -

Auto-Negotiation and Speed Sensing
00 Mbps, and 1000
Mbps, with operati e IEEE802.3 standard.
This e nod ld e
time, other nodes are oper at
A ti place when
each time a LINK is enabled. The
using 10 Mbps, 100 Mbps, or 100 ransmission speeds, with the device
at the other end of the cabl pec
what type of device is con d, a
s 0 Mbps, or 1000
If an Ethernet Switch RJ4 rn
device, it will default to 10 Mbps speed duplex mode, as required by
the IEEE802.3 standard.
Specifications
Specifications and Pin A me
Technology
Standards 80
0
0
I
R 0/ d
LED Indica
DIP Switch eak alar
Alarm Contact ela of
IP30 protection, metal case
mbient Relative
Humidity
5 to 95% (non-condensing)
The Ethernet Switch RJ45 Ethernet ports independently support
auto-negotiation for transmission speeds of 10 Mbps, 1
on according to th
means that som es cou be operating at 10 Mbps, while at the sam
100 Mbps or 1000Mbps.
ating
uto-nego ation takes an RJ45 cable connection is made, and then
Ethernet Switch advertises its capability for
0 Mbps t
e ex
necte
ted to advertise similarly. Depending on
this will result in agreement to operate at
peed of 1 Mbps, 100 Mbps.
et port is connected to a non-negotiating
and half-
5 Ethe
ssign nts
IEEE 2.3 for 10BaseT,
IEEE 8
IEEE 8
2.3u for 100BaseT(X),
2.3ab for 1000BaseT,
nterface
J45 Ports 10/10 1000BaseT(X) auto negotiation spee
tors PWR1,
Port br
PWR2, FAULT, 10/100M/1000M
m, broadcast storm protection
One r y output with current carrying capacity
1A @ 24 VDC
Power
Input Voltage 12/24/48 VDC (9.6 to 60 VDC)
Input Current @ 24VDC 0.2A
Connection One removable 6-pin terminal block
Overload Current
Protection
Present
Reverse Polarity
Protection
Present
Mechanical
Casing
Dimension (W x H x D) 35 x 130 x 105 mm (1.37 x 4.05 x 4.13 in)
Weight 290g
Installation DIN-rail, Wall Mounting (optional kit)
Environmental
Operating Temperature 0 to 60oC (32 to 140oF)
-40 to 75°C (-40 to 167°F) for -T models
Storage Temperature -40 to 85oC (-40 to 185oF)
A
- 12 -

Regulatory Approvals
Safety UL508
Hazardous Location UL/cUL Class I, Division 2, Groups A, B, C, and
ATEX Class I, Zone 2, Ex nC nL I
D;
IC T4
lass A
IEC60068-2-32
0068-2-6
ives a 5 year accordance with the
s as describ e of the Weidmüller
company which has sold t arrants to you that
defects the time when the
will be repaired by Weidmüller free of charge or that Weidmüller
a new, functi e one.
sly desc product
müller g
in specific
extent per
reimbursement of expens ever legal reason, including contract
hall be excluded. Where not expressly stated otherwise in this warranty,
ditions of ity commitments
ller company which has sold the products to
Contact Information
Klingenbergstraße 16
F
E-Mail [e-mail]
Internet www.weidmueller.com
EMI FCC Part 15, CISPR (EN55022) c
EMS EN61000-4-2 (ESD), Level 3
EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 3
EN61000-4-5 (Surge), Level 3
EN61000-4-6 (CS), Level 3
EN61000-4-8
EN61000-4-11
EN61000-4-12
Shock IEC60068-2-27
Free Fall
Vibration IEC6
WARRANTY 5 years
Weidmüller g warranty on this product in
warranty term ed in the general conditions of sal
w
he products to you. Weidmüller
of which have already existed at
such products the
risk passed
will provide onally equivalent product to replace the defectiv
Safe where expres
eid
ribed otherwise in writing in this catalogue/
description, W
interoperabili
ives no warranty or guarantee as to the
systems or as to the fitness for any particular
ty
purpose. To the mitted by law, any claims for damages and
es, based on what
or tort, s
the general con purchase and the expressive liabil
therein of the respective W
pplicable.
eidmü
you shall be a
Weidmüller Interface GmbH & Co. KG
Postfach 3030
32760 Detmold
32758 Detmold
Germany
Phone [phone]
ax [phone]
- 13 -