Weidmüller Basic Line IE-SW-BL05-4GTPoE Series Manual

Unmanaged Gigabit PoE
Switches Basic Line
IE-SW-BL05-4GTPoE Series
Hardware Installation Guide
Second Edition, May 2016
1516590000/01/05.16
Important note:
This document and additional product information can be
downloaded using following link:
http://www.weidmueller.com
► Select Product Catalogue
Select „Industrial Ethernet active“
Select „PoE unmanaged Switches“
Select Product model
Click and expand section „Downloads“
Download needed documentation
Copyright Notice
Copyright 2016 Weidmüller Interface GmbH & Co. KG
All rights reserved.
Reproduction without permission is prohibited.

2
Overview
The IE-SW-BL05-4GTPoE series consists of rugged industrial 5-port
Gigabit PoE switches for environments that fall under the pollution
degree 2 category. The industrial Ethernet switches support IEEE
802.3, IEEE 802.3u, IEEE 802.3x with 10/100/1000M, full/half-duplex,
MDI/MDIX auto-sensing, IEEE 802.3z with 1000M full-duplex (SFP
model), and IEEE 802.3af/IEEE 802.3at PoE standards.
The IE-SW-BL05-4GTPoE series provides 12/24/48 VDC redundant
power inputs that can be connected simultaneously to a live DC power
source. The switches are available with a standard operating
temperature range from 0 to 60°C, or with a wide operating temperature
range from -40 to 75°C (T-models), and their IP30 metal housing makes
them rugged enough for any harsh industrial environment.
To provide greater versatility for use with applications from different
industries, the IE-SW-BL05-4GTPoE switches also allow users to
enable or disable broadcast storm protection, 802.3az, Jumbo frame
and PoE high power with DIP switches on the outer panel. The IE-SW-
BL05-4GTPoE switches can be easily installed on a DIN-Rail or in
distribution boxes. The DIN-Rail mounting capability and IP30 metal
housing with LED indicators make the plug-and-play IE-SW-BL05-
4GTPoE switches reliable and easy to use.
Package Checklist
Your Gigabit PoE Switch is shipped with the following items. If any of
these items is missing or damaged, please contact your Weidmüller
customer service for assistance.
•1 Ethernet Switch of IE-SW-BL05-4GTPoE series
•Hardware Installation Guide
Features
High-watt Power-over-Ethernet
•Up to 30 watts output per PoE port (IEEE 802.3at)
•Supports PoE high power output up to 36 W
•Short circuit and over current protection
•Auto detection for IEEE 802.3af and IEEE 802.3at
High Performance Network Switching Technology
•10/100BaseT(X), 1000BaseT and 1000BaseX (SFP)
•10/100/1000M, Full/Half-Duplex, MDI/MDIX auto-sensing
•IEEE 802.3/802.3u/802.3x
•Store and Forward switching process type 8K MAC address entries
•Supports jumbo frames up to a length of 10 KBytes
Rugged Design
•Redundant dual 12/24/48 VDC power inputs
•Operating temperature range from 0 to 60°C, or extended operating
temperature of -40 to 75°C for (T) models.
•IP30 metal housing
•DIN-rail or panel mounting ability

3
Panel Layout of IE-SW-BL05-4GTPoE series
IE-SW-BL05-1GS-4GTPoE IE-SW-BL05-1GT-4GTPoE
Front Panel View Front Panel View
Device description:
1. Terminal blocks for
P1/P2 power inputs
2. Power input P1 LED
3. Power input P2 LED
4. PoE status LED
5. 10/100/1000Base-T(X)
PoE ports (port 2,3,4,5)
6. TP port speed LED
7. 10/100/1000BaseT(X)
port (port 1)
8. 100/1000BaseX SFP
slot
9. Article number
10. Grounding screw
11. P1 power input terminal
block
12. P2 power input terminal
block
13. DIP switches
14. Screw holes for panel
mounting kit
15. DIN-Rail mounting kit

4
Mounting Dimensions (unit = mm)
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the
back panel of the switch when you take it out of the box. If you need to
reattach the DIN-Rail attachment plate, make sure the stiff metal spring
is situated towards the top, as shown in the figures below.
STEP 1: Insert the top of the DIN-
rail into the slot just below the stiff
metal spring.
STEP 2: The DIN-Rail attachment
unit will snap into place as shown
below.
To remove the switch from the DIN-Rail, simply reverse Steps 1 and 2
above.

5
Wall Mounting (optional)
For some applications, you will find it convenient to mount the IE-SW-
BL05 switch on the wall, as shown in the following figures.
STEP 1: Remove the
aluminum DIN-Rail
attachment plate from the
switch´s rear panel, and
then attach the wall mount
plates as shown in the
diagram at the right.
STEP 2:
Mounting the switch on the wall requires 4 screws.
Use the switch, with wall mount plates attached, as a
guide to mark the correct locations of the 4 screws.
The heads of the screws should be less than 6.0 mm
in diameter, and the shafts should be less than 3.5
mm in diameter, as shown in the figure at the right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw into
one of the keyhole-shaped apertures of the wall mounting
plates. Do not screw the screws in completely—leave about 2
mm to allow room for sliding the wall mount panel between the
wall and the screws
STEP 3:
Once the screws are fixed on the wall, insert the four screw heads
through the large parts of the keyhole-shaped apertures, and then slide
the switch downwards, as indicated. Tighten the four screws for added
stability.

6
Wiring Requirements
WARNING
Safety First
Turn the power off before disconnecting modules or wires. The
correct power supply voltage is listed on the product label.
Check the voltage of your power source to make sure that you
are using the correct voltage. Do NOT use a voltage greater
than what is specified on the product label
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size. If the current
goes above the maximum ratings, the wiring could overheat,
causing serious damage to your equipment.
You should also pay attention to the following points:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power
wiring in the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb
is that wiring that shares similar electrical characteristics can be
bundled together.
•Keep input wiring and output wiring separated.
•It is strongly advised that you label wiring to all devices in the
system when necessary.
Grounding the Ethernet Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.
Wiring the Redundant Power Inputs
The two 2-contact terminal block connectors on the switch’s top panel
are used for the switch’s two DC power inputs. Top and front views of
the terminal block connectors are shown here.

7
STEP 1: Insert the negative/positive DC wires into the
V-/V+ terminals.
STEP 2: To keep the DC wires from pulling loose, use a
small flat-blade screwdriver to tighten the wire-clamp
screws on the front of the terminal block connector.
STEP 3: Insert the plastic terminal block connector prongs
into the terminal block receptor, which is located on
Switch’s top panel.
ATTENTION
Before connecting the Ethernet Switch to the DC power
inputs, make sure the DC power source voltage is
stable.
Communication Connections
The IE-SW-BL05-4GTPoE switches have 4x 10/100/1000BaseT(X) PoE
Ethernet ports for connecting PoE devices, and 1x 10/100/1000BaseT
port or 1 100/1000BaseX SFP slot for uplink connection. For fiber
connections, a field installed optical transceiver must be UL
Recognized, in the Class I category, and contain the following CDRH
Certification Marking: ‘Complies with 21CFR 1040.10 and 1040.11’.
10/100/1000BaseT(X) Ethernet Port Connection
10/100/1000BaseT(X) ports located on the Switch’s front panel are
used to connect to Ethernet-enabled devices. Below we show pinouts
for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and
also show cable wiring diagrams for straight-through and cross-over
Ethernet cables.
10/100BaseT(x) RJ45 Pinouts
MDI Port Pinouts
MDI-X Port Pinouts
8-pin RJ45
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Pin
Signal
1
Rx+
2
Rx-
3
Tx+
6
Tx-

8
1000BaseT RJ45 Pinouts
Pin
MDI
MDI-X
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
PoE Ethernet Port Connection
PoE ports located on the switch’s front panel are used to
connect to PoE-enabled devices. The pinout follows the
“Alternative A, MDI mode” of 802.3af/802.3at standards. Please
see the details in the following table.
PoE Port Pinouts
8-pin RJ45
Pin
Power
1
V+
2
V+
3
V-
6
V-
NOTE
According to IEEE 802.3af/at standards, the PD shall be
implemented to be insensitive to the polarity of the power
supply and shall be able to operate per MDI mode and MDI-X
mode. However, some PDs only support MDI mode or MDI-X
mode only. The following figure shows how to select the correct
cable between the PD and IE-SW-BL05-4GTPoE switch.

9
RJ45 (8-pin) to RJ45 (8-pin) Cable Wiring
NOTE
If the PD only supports PoE MDI mode (V+, V+, V-, V- for pins
1, 2, 3, 6), choose a cross-over Ethernet cable to connect the
PD and the switch. If the PD only supports PoE MDI-X mode
(V-, V-, V+, V+ for pins 1, 2, 3, 6), choose a straight-through
Ethernet cable between the PD and the Switch.
Redundant Power Inputs
Both power inputs can be connected simultaneously to live DC power
sources. If one power source fails, the other live source acts as a
backup, and automatically supplies all of the switch’s power needs.

10
DIP Switch Settings
The default setting for each DIP Switch is OFF. The following table
explains the effect of setting the DIP Switches to the ON positions.
IE-SW-BL05-1GT-4GTPOE
(Copper Model)
IE-SW-BL05-1GS-4GTPOE
(SFP Model)
DIP Switch
Setting
Description
BSP
ON
Enable broadcast storm protection
OFF
Disable broadcast storm protection
Jumbo
Frame
ON
Enable jumbo frame function
OFF
Disable jumbo frame function
802.3az
ON
Enable the energy-efficient Ethernet function
OFF
Disable the energy-efficient Ethernet function
PoE High
Power
ON
Supports PoE high power output up to 36 W. PoE
high power is activated when an 802.3af or
802.3at connection is detected.
OFF
Supports standard PoE power output up to 30 W
100/1G SFP
(For SFP
model only)
ON
Supports 100M SFP module
OFF
Supports 1000M SFP module
–––
(For copper
model only)
–
Serves no function (reserved for future use)
ATTENTION
To actively update DIP switch settings, power off and then
power on the switch.

11
LED Indicators
The front panel of the Switches contain several LED indicators. The
function of each LED is described in the following table.
LED
Color
State
Description
PWR1
AMBER
On
Power is being supplied to power input
P1.
Off
Power is not being supplied to power
input P1.
PWR2
AMBER
On
Power is being supplied to power input
P2.
Off
Power is not being supplied to power
input P2.
10/100/
1000M
AMBER
On
TP port’s 10/100 Mbps or SFP port’s
100 Mbps link is active.
Blinking
Data is being transmitted at 10/100
Mbps.
Off
TP port’s 10/100 Mbps or SFP port’s
100 Mbps link is inactive.
GREEN
On
TP/SFP port’s 1000 Mbps link is active.
Blinking
Data is being transmitted at 1000
Mbps.
Off
TP/SFP port’s 1000 Mbps link is
inactive.
PoE+
AMBER
On
The PoE device is connected by the
IEEE 802.3af standard
Blinking
(1 time/s)
The PoE power has been shut off
because the power budget is too low.
Off
No PoE power output or no PoE
connected PoE devices
Green
On
The PoE device is connected by IEEE
802.3at standard or PoE High Power
Off
No PoE power output or no PoE
connected PoE devices
Red
Blinking
PoE failure:
- 1 time/s: PoE standard detection
1x………..failure
- 2 times/s: PoE current overload
Off
No PoE failure

12
Auto MDI/MDI-X Connection
The Auto MDI/MDI-X function allows users to connect the Switch’s
10/100/1000BaseT(X) ports to any kind of Ethernet device, without
needing to pay attention to the type of Ethernet cable being used for the
connection. This means that you can use either a straight-through cable
or cross-over cable to connect the Ethernet Switch to Ethernet devices.
Triple Speed Functionality and Switching
The Ethernet Switch’s 10/100/1000 Mbps switched RJ45 port auto
negotiates with the connected device for the fastest data transmission
rate supported by both devices. All models of IE-SW-BL05-4GTPoE
series are plug-and-play devices, so that software configuration is not
required at installation, or during maintenance. The half/full duplex
mode for the switched RJ45 ports is user dependent and changes (by
auto-negotiation) to full or half duplex, depending on which transmission
speed is supported by the attached device.
Note about possible lost of data packages in case of “Duplex
mismatching”
If the switch’s auto-negotiation port is connected to a non-negotiating
device, then the Switch will set its port transmission speed same as the
connected device but is unable to correctly detect the duplex mode.As
result the port is set to the correct speed but is using always the half
duplex mode as required by the IEEE 802.3u standard in such cases.
For correct transmission the non-negotiating port has to be set to half-
duplex mode (speed either 10,100 or 1000 Mbit/s).
Jumbo Frames
The IE-SW-BL05-4GTPoE series supports Ethernet jumbo frames up to
10 KByte, which is with more than 1500 bytes of payload. This function
is by default disabled and can be enabled by turning on the DIP switch
labeled “Jumbo” on the top cover. This is commonly used for large
packet size applications such as video surveillance.
Broadcast Storm Protection
The switch has built-in algorithm for limiting the amount of broadcast
packets through the switch. This function is by default disabled and can
be enabled by turning on the DIP switch labeled “BSP” on the top cover.
If the broadcast storm protection algorithm detects more than 2k
broadcast frames per second, then the switch will be suppressed from
receiving broadcast frames for a period of 2 ms to prevent any further
flooding.

13
Total Power Budget
For the total power budget, the switch will provide 62 W at 12 to 17
VDC input, 120 W at 18 to 35 VDC input, and 144 W at 36 to 57 VDC
input. The total power budget is the total amount of reserved PoE power
based on the PoE class of the PoE device. If a newly connected PoE
device causes the total reserved power to exceed the total power
budget, the newly connected PoE device will be denied power.
Input Voltage
Total Power Budget
12 VDC (12 to 17 VDC)
62 W
24 VDC (18 to 35 VDC)
120 W
48 VDC (36 to 57 VDC)
144 W
PoE Class
Reserved Power
0
15.4 W
1
4.0 W
2
7.0 W
3
15.4 W
4
30 W
PoE High Power Application
PoE High Power can be enabled by DIP switch, and supply up to 36 W
of PoE power when the PSE detects an 802.3af or 802.3at connection.
Refer to the table below for the power budget at different input voltages,
and for the number of PoE High Power Ports supported.
Input Voltage
Total
Power
Budget
Number of PoE High Power Ports
12 VDC (12 to 17 VDC)
62 W
Up to 1 PoE high power port (36 W)
24 VDC (18 to 35 VDC)
120 W
Up to 3 PoE high power port (36 W)
48 VDC (36 to 57 VDC)
144 W
Up to 4 PoE high power port (36 W)
Specifications
Technology
Standards
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X) and 100BaseFX
IEEE 802.3ab for 1000BaseT
IEEE 802.3z for 1000BaseX
IEEE 802.3x for Flow Control
IEEE 802.3af for PoE
IEEE 802.3at for PoE+
IEEE 802.3az for Energy-Efficient Ethernet
Processing Type
Store and Forward
Interface
RJ45 Ports
10/100/1000BaseT(X) auto negotiation speed,
F/H duplex mode, and auto MDI/MDI-X
connection
Fiber Port
100/1000 BaseX (SFP Slot)

14
LED Indicators
Power: PWR1, PWR2
TP Port: 10/100/1000M
Fiber Port: 100/1000M
PoE Ports: PoE+ for Port 2,3,4,5
DIP Switches
Broadcast storm protection, Jumbo Frame,
802.3az, Standard PoE/PoE High Power,
100/1G SFP
PoE
Total Power Budget
62 W @ 12 VDC (12 to 17 VDC)
120 W @ 24 VDC (18 to 35 VDC)
144 W @ 48 VDC (36 to 57 VDC)
PoE Output Voltage
53 VDC @ 12/24/48 VDC power input
PoE Output Power
15.4 W in 802.3af,
30 W in 802.3at,
36 W in high power mode
PoE Output Current
350 mA in 802.3af,
600 mA in 802.3at,
720 mA in high power mode
Overload Current
Protection at Port
Present
PoE Pinout
ModeA: Pair 1, 2 (V+); Pair 3, 6 (V-)
Power
Input Voltage
12/24/48 VDC, redundant dual inputs
Operating Voltage
12 to 57 VDC
Rated Current
5.92 A @ 12 VDC ; 5.65 A @ 24 VDC ;
3.21 A @ 48 VDC
Power Consumption
11.73 W without PDs’ consumption
Inrush Current
17.4 A @ 24 VDC (0.1 to 1 ms)
Electrical Isolation
2250 VDC to chassis for 60 s
Heat Dissipation
36.4 BTU/h
Overload Current
Protection at Input
Present
Reverse Polarity
Protection
Present
Connection
2 removable 2-contact terminal block
Physical Characteristics
Housing
Aluminum, IP30 protection
Dimensions (WxHxD)
29 x 135 x 105 mm
Weight
300 g
Installation
DIN-Rail mounting, Wall mounting (with
optional kit)
Environmental Limits
Operating Temperature
Standard models: 0 to 60°C (32 to 140°F)
Wide temp. models: -40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5 to 95% (non-condensing)

15
EMC
EMI
CISPR 22, FCC Part 15B Class A
EMS
IEC 61000-4-2 ESD: Contact: 6 kV;Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 2 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8
Standards and Certifications
Safety
UL 508
EMC
EN 55022/24, EN 61000-6-2/6-4
Vibration
IEC 60068-2-6
Shock
IEC 60068-2-27
Freefall
IEC 60068-2-32
MTBF
Time
1.257.910 hrs
Database
Telcordia (Bellcore), GB
WARRANTY
Time Period
5 years
Weidmüller gives a 5 year warranty on this product in accordance with
the warranty terms as described in the general conditions of sale of the
Weidmüller company which has sold the products to you. Weidmüller
warrants to you that such products the defects of which have already
existed at the time when the risk passed will be repaired by Weidmüller
free of charge or that Weidmüller will provide a new, functionally
equivalent product to replace the defective one. Safe where expressly
described otherwise in writing in this catalogue/product description,
Weidmüller gives no warranty or guarantee as to the interoperability in
specific systems or as to the fitness for any particular purpose. To the
extent permitted by law, any claims for damages and reimbursement of
expenses, based on whatever legal reason, including contract or tort,
shall be excluded. Where not expressly stated otherwise in this
warranty, the general conditions of purchase and the expressive liability
commitments therein of the respective Weidmüller company which has
sold the products to you shall be applicable.
Contact Information
Weidmüller Interface GmbH & Co. KG
Postfach 3030
32760 Detmold
Klingenbergstraße 16
32758 Detmold
Germany
Phone [phone]
Fax [phone]
E-Mail [e-mail]
Internet www.weidmueller.com