Weidmüller Premium Line IE-SW-PL08M Series Manual

Managed Fast Ethernet Switches
Premium Line
IE-SW-PL08M Series
(valid for product Rev. 2.0.0)
Hardware Installation Guide
Fifth Edition, July 2019
1243350000/04/07.19
Important note:
This document, the detailed user manual, additional product
information, configuration tool and latest firmware can be
downloaded using following link:
http://www.weidmueller.com
► Select Product Catalogue
 Select „Industrial Ethernet active“
 Select „PremiumLine managed Switches“
 Select Product model
 Click and expand section „Downloads“
 Download needed software or documentation
Copyright Notice
Copyright  2019 Weidmüller Interface GmbH & Co. KG
All rights reserved.
Reproduction without permission is prohibited.

-
2
-
Package Checklist
Your Ethernet Switch is shipped with the following items. If any of these
items is missing or damaged, please contact your Weidmüller customer
service for assistance.
 1 Ethernet Switch of IE-SW-PL08M series
 Hardware Installation Guide (printed)
 RJ45 to DB9 Console port cable
 Protective caps for unused ports
Optional Accessories (must be ordered separately)
 EBR-MODULE RS232 Art.No.: 1241430000
(External module for backing up and restoring the configuration via
Switch´s RS-232 Console Port)
 RM-KIT Art.No.: 1241440000
(Kit for 19"-rack mounting)
 IE-WALLMOUNT-KIT-46MM Art.No.: 1504440000
(Kit for wall mounting)
Brief Information for quick access to the
Web interface
The Web interface of the managed Switch can be accessed
via IP address 192.168.1.110 and subnet mask
255.255.255.0 (Factory default value).
Connect the PC to any port of the managed Switch and set
the PC’s IP address to a free one of range 192.168.1.0 /
255.255.255.0
Start a web browser and enter the IP address of the
connected Switch into the browser’s address line.
http://192.168.1.110
After the appearance of the l
ogin prompt, please enter
following login data (factory settings):
User name:
admin
Password:
Detmold
Note: The Web interface uses Java Runtime applets for
displaying some Switch parameters. For this reason, your
PC must have installed the Java Runtime Engine to be able
to configure the Switch without any limitations.
For general settings of the Switch parameters please
refer to the manual.

-
3
-
Panel Layout of IE-SW-PL08M(T)-8TX
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD: LED indicator
10. CPLR/TAIL: LED indicator
11. TP port's 100 Mbps LED
12. TP port's 10 Mbps LED
13. Article Number
14. 10/100BaseT(X) ports
15. Screw hole for wall mounting kit
16. DIN-Rail kit

-
4
-
Panel Layout of IE-SW-PL08M(T)-6TX-2SC(S)
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD: LED indicator
10. CPLR/TAIL: LED indicator
11. TP port's 100 Mbps LED
12. TP port's 10 Mbps LED
13. Article Number
14. 10/100BaseT(X) ports
15. 100BaseFX ports
16. FX port's 100 Mbps LED
17. Screw hole for wall mounting kit
18. DIN-Rail kit

-
5
-
Panel Layout of IE-SW-PL08M(T)-6TX-2ST
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD: LED indicator
10. CPLR/TAIL: LED indicator
11. TP port's 100 Mbps LED
12. TP port's 10 Mbps LED
13. Article Number
14. 10/100BaseT(X) ports
15. 100BaseFX ports
16. FX port's 100 Mbps LED
17. Screw hole for wall mounting kit
18. DIN-Rail kit

-
6
-
Mounting Dimensions (unit = mm)
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the
back panel of the Ethernet Switch when you take it out of the box. If you
need to reattach the DIN-Rail attachment plate, make sure the stiff
metal spring is situated towards the top, as shown in the figures below.
STEP 1:
Insert the top of the DIN-Rail into
the slot just below the stiff metal
spring.
STEP 2:
The DIN-Rail attachment unit will
snap into place as shown below.
To remove the Ethernet Switch from the DIN-Rail, simply reverse Steps
1 and 2 above.

-
7
-
Wall Mounting (with optional kit)
For some applications, you will find it convenient to mount the Switch on
the wall, as shown in the following figures.
STEP 1:
Remove the aluminum
DIN-Rail attachment plate
from the switch´s rear
panel and then attach the
wall mount plates as
shown in the diagram at
the right.
STEP 2:
Mounting the switch on the wall requires 4 screws.
Use the switch, with wall mount plates attached, as a
guide to mark the correct locations of the 4 screws.
The heads of the screws should be less than 6.0 mm
in diameter, and the shafts should be less than 3.5
mm in diameter, as shown in the figure at the right.
NOTE Before tightening the screws into the wall, make sure the
screw head and shank size are suitable by inserting the
screw into one of the keyhole-shaped apertures of the wall
mounting
plates.
Do not screw the screws in completely—leave about 2 mm to allow
room for sliding the wall mount panel between the wall and the screws.
STEP 3:
Once the screws are fixed on the wall, insert the four screw heads
through the large parts of the keyhole-shaped apertures, and then slide
the switch downwards, as indicated. Tighten the four screws for added
stability.
ATEX Information
1. Certificate number DEMKO 19 ATEX 2220X
2. Ambient range: -40°C ≤ Tamb ≤ 75°C (models with suffix –T),
-10°C ≤ Tamb ≤ 60°C (models without suffix –T)
3. Certification string: Ex nA nC IIC T4 Gc
4. Standards covered:
EN 60079-0:2012+A11:2013, EN 60079-15:2010,
5. The conditions of safe usage:
 The equipment shall only be used in an area of at least pollution
degree 2, as defined in IEC/EN 60664-1.
 The equipment shall be installed in an enclosure that provides a
minimum ingress protection of IP 54 in accordance with IEC/EN
60079-0.

-
8
-
Wiring Requirements
WARNING
The power for this product is intended to be supplied by a
Listed Power Unit, with output marked LPS, and rated to
deliver 12 to 48 VDC at a maximum of 600 mA.
WARNING
Safety First!
Be sure to disconnect the power cord before installing
and/or wiring your Ethernet Switch.
Calculate the maximum possible current in each power wire
and common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment
Be sure to read and follow these important guidelines:
 Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
 Use the type of signal transmitted through a wire to determine which
wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together.
 Keep input wiring and output wiring separate.
 It is strongly advised that you label wiring to all devices in the
system.
Grounding the Ethernet Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the ground screw to the grounding surface prior to connecting devices.
A 4 mm2 conductor must be used when connection to the external
grounding screw is utilized.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting sur
face, such as a metal panel.

-
9
-
Wiring the Relay Contact
The IE-SW-PL08M has two sets of relay output—relay 1 and relay 2.
Each relay contact consists of two contacts of the terminal block on the
IE-SW-PL08M´s top panel. Refer to the next section for detailed
instructions on how to connect the wires to the terminal block
connector, and how to attach the terminal block connector to the
terminal block receptor.
The fault circuit will open if:
1. A relay warning event is triggered, OR
2. The IE-SW-PL08M Switch is the Master of a Turbo Ring, and the
Turbo Ring is broken, OR
3. Start-up failure.
If none of these three conditions is met, the fault circuit will remain
closed.
Wiring the Redundant Power Inputs
The IE-SW-PL08M switch has two sets of power inputs - power input 1
and power input 2. Top view of both terminal block connectors is shown
below.
Take the following steps to wire the redundant power inputs:
STEP 1: Insert the negative/positive DC wires into the V-/V+ terminals.
STEP 2: To keep the DC wires from pulling loose, use a small flat-
blade
screwdriver to tighten the wire-
clamp screws on the front of the terminal
block connector.
STEP 3: Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the Ethernet Switch top
panel.
ATTENTION
Before connecting the Ethernet Switch to the DC power
inputs, make sure the DC power source voltage is stable.

-
10
-
Wiring the Digital Inputs
The IE-SW-PL08M switch has two sets of digital inputs, DI 1 and DI 2.
Each DI consists of two contacts of the 6-pin terminal block connector
on the Ethernet Switch´s top panel. Top and front views of the terminal
block connector are shown below.
Take the following steps to wire the digital inputs:
STEP 1: Insert the negative (ground)/positive DI wires into the ┴/I1
terminals.
STEP 2: To keep the DI wires from pulling loose, use a small flat-blade
screwdriver to tighten the wire-
clamp screws on the front of the
terminal block connector.
STEP 3: Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the IE-SW-
PL08M`s
top panel.
Communication Connections
The IE-SW-PL08M models have 8 or 6 10/100BaseT(X) Ethernet ports,
and 0 (zero) or 2 100BaseFX (SC/ST-type connector) fiber ports
10/100BaseT(X) Ethernet Port Connection
The 10/100BaseT(X) ports located on Ethernet Switch’s front panel are
used to connect to Ethernet-enabled devices.
Next, we show pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports, and show cable wiring diagrams for straight-
through and cross-over Ethernet cables.
MDI Port Pinouts
MDI
-
X Port Pinouts
8
-
pin RJ45
Pin
Signal
Pin
Signal
1
Tx+
1
Rx+
2
Tx
-
2
Rx
-
3
Rx+
3
Tx+
6
Rx
-
6
Tx
-
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

-
11
-
RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring
100BaseFX Ethernet Port Connection (Fiber)
Remember to connect the Tx (transmit) port of device 1 to the Rx
(receive) port of device 2, and the Rx (receive) port of device 1 to the Tx
(transmit) port of device 2. Fiber optic connections generally are using
the full-duplex transmission mode.
SC
-
Port Pinouts
SC
-
Port to SC
-
Port Cable Wiring
ST
-
Port Pinouts
ST
-
Port to ST
-
Port Cable Wiring
ATTENTION
This is a Class 1 Laser/LED product. To avoid causing
serious damage to your eyes, do not stare directly into the
Laser Beam.

-
12
-
Turbo Ring DIP Switch Settings
IE-SW-PL08M models are plug-and-play managed redundant Ethernet
switches. The proprietary Turbo Ring protocol provides better network
reliability and faster recovery time. Turbo Ring’s recovery time is less
than 300 ms (Turbo Ring) or 20 ms (Turbo Ring V2) - compared to a
3- to 5-minute recovery time for commercial switches - decreasing the
possible loss caused by network failures in an industrial setting.
There are 4 Hardware DIP Switches for Turbo Ring on the top panel of
the switch that can help setup the Turbo Ring easily within seconds. If
you do not want to use a hardware DIP switch to setup the Turbo Ring,
you can use a web browser, telnet, or console to disable this function.
NOTE Please refer to the Turbo Ring DIP Switch section and
Using Communication Redundancy section in User’s
Manual for more detailed information about the settings and
usage of Turbo Ring and Turbo Ring V2.
IE
-
SW
-
PL08M
Series DIP Switches
The default setting for each DIP Switch is OFF.
The following table explains the effect of setting
the DIP Switch to the ON position.
“Turbo Ring” DIP Switch Settings
DIP 1
DIP 2
DIP 3
DIP 4
Reserved for
future use.
ON: Enables
this Ethernet
Switch as the
Ring Master.
ON: Enables the
default “Ring
Coupling” ports.
ON: Activates
DIP switches 1,
2, 3 to configure
“Turbo Ring”
settings.
OFF: This
Ethernet Switch
will not be the
Ring Master.
OFF: Do not use
this Ethernet
Switch as the ring
coupler.
OFF: DIP
switches 1, 2, 3
will be disabled.
“
Turbo Ring V2
”
DIP Switch Settings
DIP 1
DIP 2
DIP 3
DIP 4
ON: Enables
the default
“Ring Coupling
(backup)” port.
ON: Enables
this Ethernet
Switch as the
Ring Master.
ON: Enables
the default
“Ring Coupling”
port.
ON: Activates
DIP switches 1,
2, 3 to configure
“Turbo Ring V2”
settings.
OFF: Enables
the default
“Ring Coupling
(primary)” port.
OFF: This
Ethernet Switch
will not be the
Ring Master.
OFF: Do not
use this
Ethernet Switch
as a ring
coupler.
OFF: DIP
switches 1, 2, 3
will be disabled.

-
13
-
NOTE If you do not enable any of the IE-SW-PL08M Switches to be
the Ring Master, the Turbo Ring protocol will automatically
choose the switch with the smallest MAC address to be the
Ring Master. If you accidentally enable more than one IE-
SW-PL08M switch to be the Ring Master, these switches will
auto-negotiate to determine which one will be the Ring
Master.
NOTE To switch on the Master or Coupler functions of the DIP
switch, you must enable the Turbo Ring DIP Switch first.
LED Indicators
There are several LEDs on the Ethernet Switch´s front panel. The
function of each LED is described in the following table.
LED
Color
State
Description
PWR1 AMBER
On Power is being supplied to power
input
PWR1.
Off Power is not being supplied to power
input PWR1.
PWR2 AMBER
On Power is being supplied to power
input PWR2.
Off Power is not being supplied to power
input PWR2.
FAULT RED
On
When (1) a relay warning event is
triggered, (2) the switch is the Master
of a Turbo Ring, and the Turbo Ring
is
broken
or (3)
s
tart
-
up failure
.
Off When a relay warning event is not
triggered
MSTR/HEAD GREEN
On
When the switch is set as the Master
of the Turbo Ring, or as the Head of
the Turbo Chain
Blinking
When the Turbo Ring or Turbo Chain
is broken or the switch has become
the Ring Master of the Turbo Ring, or
the Head of the Turbo Chain, after
the Turbo Ring or the Turbo Chain is
broken
Off
When the switch is not the Master of
this Turbo Ring or is set as a
Member of
a
Turbo Chain
CPLR/TAIL GREEN On
When the switch´s coupling function
is enabled to form a back-up path, or
when it is set as the Tail of a Turbo
Chain

-
14
-
Blinking
When the Turbo Chain is down.
Off
When the coupling function at the
switch is disabled or is set as a
Member of
a
Turbo Chain
10M
(TP)
Bottom LED of
RJ-45 Port
GREEN
On
TP port’s 10 Mbps link is active
Blinking
Data is being transmitted at 10 Mbps.
Off
TP Port’s 10 Mbps link is inactive
100M
(TP)
Top LED of RJ-
45 Port
GREEN
On
TP port’s 100 Mbps link is
active
Blinking
Data is being transmitted at 100
Mbps
.
Off
T
P
Port’s
100 Mbps
link is inactive
.
100M
(FX)
GREEN
On
FX port’s 100 Mbps
link
is active
Blinking
Data is being transmitted at 100
Mbps
.
Off
FX port
’s 100 Mbps
link
is inactive
.
Auto MDI/MDI-X Connection
The Auto MDI/MDI-X function allows users to connect
the10/100BaseTX ports to any kind of Ethernet device, without needing
to pay attention to the type of Ethernet cable being used for the
connection. This means that you can use either a straight-through cable
or cross-over cable to connect the IE-SW-PL08M switches to Ethernet
devices.
Specifications
Technology
Standards
IEEE 802.3 for 10BaseT,
IEEE 802.3u for 100BaseT(X) and 100Base FX,
IEEE 802.3x for Flow Control,
IEEE 802.1D for Spanning Tree Protocol,
IEEE 802.1w for Rapid STP,
IEEE 802.1Q for VLAN Tagging,
IEEE 802.1p for Class of Service,
IEEE 802.1X for Radius Authentication,
IEEE 802.3ad for Port Trunk with LACP
Protocols
IGMPv1/v2, GVRP, SNMPv1/v2c/v3, DHCP
Server/Client, BootP, TFTP, SNTP, SMTP, RARP,
GMRP, LACP, RMON, HTTP, HTTPS, Telnet,
Syslog, DHCP Option 66/67/82, SSH, SNMP Inform,
LLDP, IEEE 1588 PTP, IPv6
Industrial
Protocols
PROFINET/RT (PN-I/O device according to CC-B),
EtherNet/IP,
Modbus/TCP
MIB MIB-II, Ethernet-Like MIB, P-BRIDGE MIB, Q-
BRIDGE MIB, Bridge MIB, RSTP MIB, RMON MIB

-
15
-
Group 1,2,3,9
Forwarding and
Filtering Rate
148.810 pps
Processing Type
Store and Forward
Flow Control
IEEE802.3x flow control, back pressure flow
control
Interface
RJ45 Ports 10/100BaseT(X) auto negotiation speed, F/H duplex
mode, and auto MDI/MDI
-
X connection
Fiber Ports
100BaseFX ports (SC/ST
-
Dup
lex connector
)
Console
RS
-
232 (RJ45)
LED Indicators PWR1, PWR2, FAULT, 10/100M (TP port), 100M
(Fiber Port), MSTR/HEAD and CPLR/TAIL
Relay Contact
Two relay outputs with current carrying capacity of 1A
@ 24 VDC
DIP Switches
Master, Coupler, Turbo Ring, Reserve
Digital Input Two inputs with the same ground, but electrically
isolated from the electronics
• For state “1”: +13 to +30V
• For state “0”: -30 to +3V
• Max. input current: 8 mA
Optical Fiber
100Base FX
Multi
-
mode
Single
-
mode
Fiber Cable Type OM1
50/125 μ
m
G.652
800 MHz*k
m
Typical Distance
4 km
5 km
40 km
Wavelength
Typical
(nm)
1300
1310
TX Range
(nm)
1260 to 1360 1280 to 1340
RX Range
(nm)
1100 to 1600 1100 to 1600
Optical Power
TX Range
(dBm)
-10 to -20 0 to -5
RX Range
(dBm)
-3 to -32 -3 to -34
Link Budget
(dB)
12 29
Dispersion
Penalty (dB)
3 1
Note: When connecting single-mode fiber over a short distance, we
recommend putting an attenuator to prevent the transceiver from being
damaged by excessive optical power.
Typical Distance: To reach the typical distance of a specified fiber
transceiver, please refer to the following formula: Link budget(dB) >
dispersion penalty(dB) + total link loss(dB).

-
16
-
Power
Input Voltage
12/24/48 V
DC,
2 redundant inputs
Input Current
(@ 24 V)
IE-SW-PL08M(T)-8TX: max. 0.22 A
IE-SW-PL08M(T)-6TX-2SC/2ST/2SCS: max. 0.3 A
Rating 12/24/48 VDC, 0.62/0.3/0.16 A
Relay output 24 VDC/1 A (Resistive), Class 2
Connection
Two
removable 6
-
pin terminal block
s
Overload Current
Protection
Present
Reverse Polarity
Protection
Present
Mechanical
Housing
Metal, IP30 protected
Dimensions
80.5

135

105 mm (W

H

D)
Weight
1.04 kg
Installation
DIN
-
Rail, Wall Mounting
(optional kit)
Environment
Operating
Temperature
Standard models: -10 to 60°C (14 to 140°F)
Wide temp. models:
-
40 to 75°C (
-
40 to 167°F)
Storage
Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5% to 95% (non-condensing)
Regulatory Approvals
Safety
U
L60950
-
1, UL 508,
EN60950
-
1
(LVD)
Hazardous
Location
UL/cUL Class I, Division 2, Groups A, B, C, and D
ATEX Zone 2:
EN 60079-0:2012+A11:2013
EN 60079
-
15:2010
EMC
EN 55032/24; CISPR 32, FCC Part 15B Class A
IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 20 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 10 V
IEC 61000
-
4
-
8
PFMF
Shock
IEC60068
-
2
-
27
Freefall
IEC60068
-
2
-
31
Vibration
IEC60068
-
2
-
6
MTBF
(meantime between failures)
Time
1,105,486 hrs (IE-SW-PL08M(T)-8TX)
1,043,909 hrs (IE-SW-PL08M(T)-6TX-
2SC/2ST/2SCS
)
Database
Telcordia (Bellcore), GB
WARRANTY
Time Period
5 years

-
17
-
WARNING This equipment is intended to be used in a
restricted access location.
HOT SURFACE!! Before touching it, special
attention or protection is required.
Weidmüller gives a 5 year warranty on this product in accordance with
the warranty terms as described in the general conditions of sale of the
Weidmüller company which has sold the products to you. Weidmüller
warrants to you that such products the defects of which have already
existed at the time when the risk passed will be repaired by Weidmüller
free of charge or that Weidmüller will provide a new, functionally
equivalent product to replace the defective one. Safe where expressly
described otherwise in writing in this catalogue/product description,
Weidmüller gives no warranty or guarantee as to the interoperability in
specific systems or as to the fitness for any particular purpose. To the
extent permitted by law, any claims for damages and reimbursement of
expenses, based on whatever legal reason, including contract or tort,
shall be excluded. Where not expressly stated otherwise in this
warranty, the general conditions of purchase and the expressive liability
commitments therein of the respective Weidmüller company which has
sold the products to you shall be applicable.
Contact Information
Weidmüller Interface GmbH & Co. KG
Postfach 3030
32760 Detmold
Klingenbergstraße 16
32758 Detmold
Germany
Phone [phone]
Fax [phone]
E-Mail [e-mail]
Internet www.weidmueller.com