Weidmüller IE-SW-EL10-8GT-2GESFP Manual

4 5 6 V1.0 / 2020-10-29
Hardware Installation Guide
Unmanaged Gigabit Ethernet Switches
IE-SW-EL10-8GT-2GESFP (Part No. 2682240000)
1. Introduction
Ethernet Switches from Weidmüller are designed with a very compact housing size and
are fitted with a robust housing. To ensure reliable, error-free operation, and to prevent
damage or injury, please read the operating instructions, all safety information provided
in this document and any other safety information that were supplied with the product.
2. Safety notice
Switch off the electrical power before removing the power connection!
The device heats up during operation. Allow the unit to cool down or use
protection gloves when carrying out any work.
The device may only be connected to the supply voltage shown on the
product label. Higher voltage than specified will destroy the device.
The device must be supplied by a SELV source as defined in the Low
Voltage Directive 2014/35/EU and 2014/30/EU.
Installation, commissioning and maintenance may only be performed by
qualified electricians.
Observe the operating instructions.
Indoor use and pollution degree II, it must be wiped with a dry cloth for
clean up the device and label.
oUtilisation en intérieur et degré de pollution II, il faut l'essuyer avec un
chiffon sec pour nettoyer l'appareil et son étiquette.
Do not block air ventilation holes.
oNe bouchez pas les orifices de ventilation.
If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.
oSi l’appareil est utilise d’une maniere non specifiee par le fabricant, la
protection qu’il apporte peut se voir diminuee.
Shall be mounted in the Industrial Control Panel and ambient
temperature is not exceed 75 degrees C.
oDoit être monté dans le panneau de commande industriel et la
température ambiante ne doit pas dépasser 75 degrés C.
Intended use
The device is intended for the realization of communication networks within an industrial
environment, it is intended to be used in a restricted access location. The device may only be used
within the scope of the specified technical data. The device is intended to be mounted to a well-
grounded mounting surface, such as a metal panel. Any other use may result in unintentional
malfunction and damage. Observing the documentation is part of the intended use.
Environmental conditions
This equipment is intended to be used in a restricted access location.
When planning the installation site make sure that the ambient temperature during operation will not
exceed the temperature given in the technical data.
Also make sure that the air flow will not be compromised by other devices.
Ensure that the mounted and wired device is not exposed to any mechanical stress.
FCC compliance
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
3. Package Checklist
Your Ethernet Switch is shipped with the following items:
Ethernet Switch
Hardware Installation Guide (printed)
4-Pin Terminal connector
Protective caps for RJ45 ports and SFP ports
4. Panel Layouts
1. Terminal block for power input PWR1 /
PWR2
2. Grounding screw / Frame ground (Note:
The shielding ground of the LAN port is
electrically connected to the grounding
screw)
3. Power input LEDs (PWR1 / PWR2)
4. SFP slot 100/1000Base-X for SFP
transceiver
5. SFP Port Link/Activity LED
6. SFP Port Speed LED (100/1000 Mbps)
7. 10/100/1000Base-T(X) ports
8. RJ45 Port Link/Activity LED
9. RJ45 Port Speed LED (10/100/1000
Mbps)
10. Article Number
11. DIN-Rail kit
5. Mounting Dimensions
(units = mm)
6. DIN-Rail Mounting
Slide the switch onto a DIN-rail and make sure that the switch’s Din-rail clip clicks into
the rail firmly.
STEP 1: Insert the top of the
DIN-Rail into the slot just below
the stiff metal spring.
STEP 2: The DIN-Rail
attachment unit will snap into
place as shown below.
To remove the DIN-rail from the Ethernet Switch, simply reverse Steps 1 and 2.
7. Grounding Ethernet Switch
ATTENTION
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI).
the ground connection from the ground screw to the grounding
surface prior to connecting devices.
This product is intended to be mounted to a well-grounded mounting
surface, such as a metal panel.
The shielding ground of the RJ45 ports are electrically connected to
the ground connection (screw).

4 5 6 V1.0 / 2020-10-29
8. Wiring the Redundant Power Inputs
The switch supports redundant power supply inputs which are located on the 4-pin
terminal block. Refer to illustration below for correct wiring.
Warning / Avertissement
Take into consideration the following guidelines before wiring the
device
oTenez compte des directrices suivantes avant de câbler l’appareil.
Terminal block is mating with Plug and suitable for 12-24AWG.
Torque value 4.5 lb-in.
oLe bornier est compatible avec les connecteurs et convient pour 12-
24AWG. Valeur de couple 4,5 lb-in.
The temperature rating of the input connection cable should higher
than 105°C.
oLa température de service nominale du câble d’entrée doit être
supérieure à 105 °C.
Use Copper Conductors Only.
oUtilisez uniquement des conducteurs en cuivre.
Supplied by SELV or double insulation source evaluated by UL
61010-1 or 61010-2-201 power supply only.
oFourni par la source SELV ou double isolation évaluée uniquement
par l'alimentation UL 61010-1 or 61010-2-201.
9. Communication Connections
Switch IE-SW-EL10-8GT-2GESFP is equipped with following communication
interfaces:
8x 10/100/1000Base-T(X) Ethernet ports
2x 100/1000Base-X slot to be used with SFP Transceivers (mini-GBIC)
[accessories]
Please only use cables suitable for the respective type of communication and ensure
that signals are protected from possible interference.
9.1 10/100/1000Base-T(X) RJ45 Ports
The 10/100BaseT(X) ports located on Ethernet Switch’s front panel are used to
connect to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type)
ports and MDI-X (HUB/Switch-type) ports. Auto MDI-X ensures that both wiring-
schemes are supported (Automatic crossover function).
Pinouts 10/100/1000Base T(X) RJ45
8-Pin RJ45
Port
10/100 Base-T(X) MDI/MDI-X 1000Base-T MDI/MDI-X
Pin No. MDI port MDI-X port Pin No. MDI port MDI-X port
1 TD+(transmit) RD+(receive) 1 BI_DA+ BI_DB+
2 TD-(transmit) RD-(receive) 2 BI_DA- BI_DB-
3 RD+(receive) TD+(transmit) 3 BI_DB+ BI_DA+
4 Not used Not used 4 BI_DC+ BI_DD+
5 Not used Not used 5 BI_DC- BI_DD-
6 RD-(receive) TD-(transmit) 6 BI_DB- BI_DA-
7 Not used Not used 7 BI_DD+ BI_DC+
8 Not used Not used 8 BI_DD- BI_DC-
9.2 100/1000BaseSFP Port
The 100/1000BaseSFP type slots require either a 100BaseSFP or a 1000BaseSFP
fiber transceiver (mini-GBIC) to work properly.
Please only use SFP modules and cables that are compatible with each other to
establish an optical connection. Weidmüller provides transceiver models for various
distance requirements.
LC-Port with separate Transmit and Receive Port:
Remember to connect the Tx (transmit) port of device I to the Rx (receive) port of device
II, and the Rx (receive) port of device I to the Tx (transmit) port of device I
LC-Port Pinouts LC-Port to LC-Port Cable Wiring
10. LED Indicators
The front panel of the Ethernet Switch contains several LED indicators. The function of
each LED is described in the table below.
LED Color Status Description
PWR1 Green
On Power is being supplied to power input
PWR1.
Off Power is not being supplied to power
input PWR1.
PWR2 Green
On Power is being supplied to power input
PWR2.
Off Power is not being supplied to power
input PWR2.
LNK/ACT Green On Port’s link is active.
Off Port’s link is inactive.
10/100/1000M Green /
Amber
Green Port’s speed is 1000 Mbps.
Amber Port’s speed is 100 Mbps.
Off Port’s speed is 10 Mbps.
11. Specifications
Technology
Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3ab for 1000Base-T
IEEE 802.3z for 1000Base-X
IEEE 802.3x flow control
Processing Type Store and Forward
MAC Table size 4K
Packet buffer size 1.5 Mbit
Backplane bandwidth 20 Gbps
Jumbo frame support up to 9KB
Interfaces
RJ45 Ports 10/100/1000Base-T(X) auto negotiation speed, F/H
duplex mode and auto MDI/MDI-X connection
Fiber optic port 100/1000Base SFP slot
LED Indicators PWR1, PWR2 (Power), Port Link/Activity, Port Speed
Power
Input Voltage 24 V DC (12 - 48 V DC), 2 redundant inputs
Input Current
0.41 A @ 12 V DC
0.20 A @ 24 V DC
0.11 A @ 48 V DC
Connection One removable 4-pin terminal block,
Wiring cable 12-24 AWG
Overload Current
Protection Present
Reverse Polarity Protection Present
Physical Characteristics
Housing IP30 protection, metal
Dimension (W x H x D) 41 x 127 x 90 mm (1.61 x 5.0 x 3.54 in)
Weight 400 g
Installation DIN-rail
Environmental conditions
Operating Temperature -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Altitude up to 2000 m
Regulatory Approvals
Safety UL 61010-1, UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A,
IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 2 kV,
IEC 61000-4-5 Surge: Power: 1 kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 Vrms
Shock IEC 60068-2-27
Free Fall IEC 60068-2-31
Vibration IEC 60068-2-6
MTBF
Time 1.056.516 hrs
Database Telcordia SR332
Warranty
Time Period 5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone [phone], Fax [phone]
E-Mail [e-mail], Internet www.weidmueller.com