Well 3130IF User manual

JOYCE ČR, s.r.o., Venhudova 6, 614 00 Brno, ČR, IČ: 25317571, DIČ: CZ25317571, Tel.: [phone]
Fax: +420 5
39 088
00
0
,
E
-
mail: [e-mail]
,
Web: www.joyce.cz, www.joyce
-
energie.cz
Provisioning manual WELL 3195IF
V 1.3
Auto Provision Manual for WELL 3195IF and
3130IF

Summary:
This documents will show you how to auto provision works and how to make auto provision work. The process of a
successful auto provision is :
1, Obtain a server address in which store the configuration files.
2, Download the configuration files from the configured server.
3, Resolve and apply the configuration written in the configuration file.
4, Do other updates, for example the firmware updating.
Step 1: Obtain the server address.
After phone boots up, you should configure the server address for this device, so it will update after reboot or
update at time interval, this can set by yourself from phone.:
In the maintenance page, AUTO PROVISION sub page, current Config Version show you the current Configure
file version.
ServerAddress, you can configure the server address here (HTTP,TFTP or FTP).
Username and Password you should set this when you select the FTP update mode.
Config File Name: fill the configure file name here , then phone can request from server.
Config Encrypt Key: Fill the Encrypt key if have.
Protocol Type: you can configure the Protocol type here.
Update Interval Time : you can set the update interval by hour.
Update Mode: you can set the update mode to update after reboot or update at time interval.
Step 2: Download configuration files
After setup the Server which use to store the configure files. Then to Download the configuration files.
If you select HTTP server, you can set a free simple HTTP server, as below: also you can select other HTTP server.

If you select FTP server , also you can set a free simple FTP server, as below, also you can select other FTP server.
When you select TFTP mode the same method as HTTP or FTP server.
After done, Phone can send request to Configure file sever, and update the configure files.
Step 3: Resolve and then apply the configuration
After device download configure files from server successfully, the next step, device will resolve and apply the
configuration automatically.
If the downloaded configuration files have been encrypted, the specified Encrypt key will be needed. The specified
Encrypted key is for decrypting the common configuration files. The Keys supported characters are: 0~9,a~z,A~Z,and

the following special characters:# $ % * + - : = ? @ [ ] ^ _ { } ~ .
In a configuration file, there are the texts defining configurations , here is the brief description to the texts.
In the configuration file there will show the current value for each options, detail information please check Appendix
I.
Step 4: Do others updates
For the other update such as firmware update, also you need to configure In the MAINTENANCE page (UPDATE
sub page):
You can use two modes to update the firmware, web mode or FTP mode.

Appendix I
Modules Parameter
s Permitted Values Descriptions
Static IP IP
Address It defines the IP Address when using static WAN settings.
Static
NetMask Network Mask It defines the Static NetMask when using static WAN setting
Static
GateWay IP Address It defines the Default Gateway when using static WAN setting
DNS
Domain String for domain It define the DNS domain name when using static WAN setting.
Primary
DNS IP Address It defines Primary DNS when using static WAN setting
Alter DNS IP
Address It defines Alter DNS when using static WAN setting.
DHCP
Mode 0,1 It define the WAN port mode, set to 1 to enable DHCP, 0 to disable this feature.
DHCP
DNS 0,1 It set to obtain DNS server automatically 0—to disable this feature
1—to enable this feature
Default
Protocol 1,2,3 1—Static IP mode 2—DHCP mode
3—PPPoE mode
Host name Strings It define the host name for this device;
default value is VOIP
PPPoE
Mode 0,1 It set the PPPoE mode 0—it shows the device not using this mode
1—it shows the device using this mode
GLOBAL
CONFIG
MODULE
HTL Start Int It define the start RTP port for RTP string

Port using ,default using 10000
HTL Port
number Int It define the quantity of RTP ports, default value 200
SNTP
Server IP address It define the NTP server’s address. Where the device get the time. Default using
209.81.9.7
Enable
SNTP 0,1 0- to disable this feature 1- to enable this feature
Time
Zone 0~74 This is drop down list for you to setting your Time Zone
Enable
Day light 0,1 0- to disable this feature 1- to enable this feature
SNTP
Time out Int It define the time range when there is no response from SNTP sever
DayLight
Shift Min Int It define the DayLight Shift value in minutes.
Default value is 60
Daylight
start Mon 1~12 It define the start month of Day light
Daylight
start Week
1-5 It defines the start week of the day light.
Daylight
start day 1-31 It defines the start day of the day light
Daylight
start Hour
1-24 It defines the start Hour of the day light
Daylight
start Min 1-60 It define the start Minutes of the day light
Daylight
End Mon 1-12 It define the end month of the day light
Daylight
End Week 1-5 It define the end week of the day light
Daylight
End day 1-31 It define the end day of the day light
Daylight
End Hour 1-24 It defines the end Hour of the day light.
Daylight
End Min 1-60 It defines the end Minutes of the day light
MMI Set Int It define the MMI language for the phone
MTU
Length Int It define the max packet length, default value is 1500
Lan IP IP address It define the IP address of the LAN port
Lan
NetMask Net Mask It define the Net mask of LAN port
LAN
CONFIG
MODULE Bridge
Mode 0,1 It define the port to enable the Bridge mode or disable it
Dial End
with # 0,1 0- to disable this feature 1- to enable this feature
Dial Fixed
Length 0,1 0- to disable this feature 1- to enable this feature
Fixed
Length Int It define the number length, when match this phone will send the number our
automatically
TELE
CONFIG
MODULE
Dial with
Timeout 0,1 0- to disable this feature 1- to enable this feature

Dial
Timeout
Value
Int It define a time value
Dialpeer
with line 0,1 0- to disable this feature 1- to enable this feature
Poll
Sequence
Accept
any call 0,1 0- to disable this feature 1- to enable this feature
Phone
Prefix Int It define the prefix for this phone
Local
Area code Int It define the Local area code
IP call
network 0,1 0- to disable this feature 1- to enable this feature
P1 No
Disturb 0,1 0- to disable this feature 1- to enable this feature
P1 No
Dial out 0,1 0- to disable this feature 1- to enable this feature
P1 No
Empty
Calling
0,1 0- to disable this feature
1- to enable this feature
P1 Enable
caller ID 0,1 0- to disable this feature 1- to enable this feature
P1
Forward
service
0,1 0- to disable this feature
1- to enable this feature
P1 SIP
TransNum
Int It define the sip number
P1 SIP
TransAdd
r
IP address It define the sip address
P1 SIP
TransPort 1-65535 It define the networks port that for sip using, default using 5060
P1 Call
waiting 0,1 0- to disable this feature 1- to enable this feature
P1 Call
Transfer 0,1 0- to disable this feature 1- to enable this feature
P1 Call
3way 0,1 0- to disable this feature 1- to enable this feature
P1 Auto
Answer 0,1 0- to disable this feature 1- to enable this feature
P1 No
Answer
Time
Int It define a time value for control the time
before auto answer
P1
Extension
No.
Int It defines the extension no.
P1 Hotline
num Int It define the Hotline num
P1 Record
server IP address It define the call record server
P1 Enable
Record 0,1 0- to disable this feature 1- to enable this feature

P1 Auto
Replace 0,1 0- to disable this feature 1- to enable this feature
P1 Busy
N/A Line 0,1 0- to disable this feature 1- to enable this feature
P1 Auto
Handdow
n
0,1 0- to disable this feature
1- to enable this feature
Signal
Standard Int It define the signal type
Handdow
n time Int It define the time value for handdown
G.729
PayLoad
Length
Int It define the payload length for voice codec
G.723 Bit
Rate Int It define the G.723 Bit rate
G.722
Timestam
ps
0,1 0- to disable this feature
1- to enable this feature
VAD 0,1 0- to disable this feature
1- to enable this feature
Ring Type 1-13 It define the ring type through the drop
down list
DTMF
Payload
Type
Int It define the DTMF Payload type default
value is 101
Disable
Handfress 0,1 0- to disable this feature 1- to enable this feature
RTP
PROBE 0,1 0- to disable this feature 1- to enable this feature
P1 Output
Vol Int It define the Output volume value for output direction
P1 Input
Vol Int It define the input volume value for input direction
P1
HandFree
Vol
Int It define the handfree volume
P1 Ring
Tone Vol Int It define the ring tone volume
P1 codec Int It use to setting use which codec
P1 Voice
record 0,1 0- to disable this feature 1- to enable this feature
P1 Record
Playing 0,1 0- to disable this feature 1- to enable this feature
DSP
CONFIG
MODULE
P1
UserDef
Voice
0,1 0- to disable this feature
1- to enable this feature
P1 First
Codec Int It define the first prefer voice codec
P1 second
codec Int It define the second prefer voice codec
P1 third
codec Int It define the third prefer voice codec
P1 forth Int It define the forth prefer voice codec

codec
P1 Fifth
codec Int It define the fifth prefer codec
P1 Sixth
codec Int It define the sixth prefer voice codec
SIP port 1-65535 It define the local sip port, default using
5060
Stun
address IP address It define the IP address of STUN server
Stun
effect time
Int It define the time length which stun take
effect
Stun port 1-65535 It define the network port for stun using
,default using 3478
SIP
Differv 0,1 0- to disable this feature 1- to enable this feature
Extern
Address Ip address It define a extern address
Url
Convert 0,1 0- to disable this feature 1- to enable this feature
Reg Retry
time Int It define a time interval value , when Reg fail after how long it will register again
Strict
BranchPre
fix
0,1 0- to disable this feature
1- to enable this feature
Sip Phone
Number Int There to setting the phone number
SIP1
Display
name
String This option to setting the display name
SIP1 Sip
Name String This option to setting the sip Name
SIP1
Register
Addr
IP address This option to set the sip server ‘s address
SIP1
Register
port
1-65535 This option to set the sip server’s port
SIP1
Register
User
Int This option to set the extension number
SIP1
Register
Pwd
Int or
string This option to set the sip password
SIP1
Register
TTL
Int This option to define the TTL time value
SIP1
Enable
Reg
0,1 0- to disable this feature
1- to enable this feature
SIP1
Proxy
Addr
IP address This option use to set the proxy address
SIP CONFIG
MODULE
SIP1
Proxy Port
1-65535 This option to define sip proxy server ‘s
port

SIP1
Proxy user
Int This option to define the user
SIP1
Proxy
Pwd
Int This option to define the password
SIP1
Signal
Enc
0/1 0- to disable this feature
1- to enable this feature
SIP1
Singal
Key
Int This option use to set the signal key
SIP1
Media
Enc
0/1 0- to disable this feature
1- to enable this feature
SIP1
Media
Enc
Int This option use to set the Media key
SIP1
Local
Domain
String This option use to set the local domain
SIP1
FWD
service
0,1 0- to disable this feature
1- to enable this feature
SIP1 Ring
Type 1-13 This option for you to set the ring type
SIP1
FWD
number
Int This option use to target number for FWD
feature
SIP1
HotLine
number
Int This use to define the Hotline number
SIP1
Enable
Detect
0,1 0- to disable this feature
1- to enable this feature
SIP1
Detect
TTL
Int This option define when to detect the TTL
SIP1
Server
Type
Int This option to set the server type
SIP1 User
Agent String This option use to define the user agent string
SIP1
PRACK 0,1 0- to disable this feature 1- to enable this feature
SIP1
KEEP
AUTH
0,1 0- to disable this feature
1- to enable this feature
SIP1
Session
Timer
0,1 0- to disable this feature
1- to enable this feature
SIP1 Gruu 0,1 0- to disable this feature
1- to enable this feature
SIP1
DTMF Int This option use to define the DTMF type