Wells HW/SMP-6D User manual

WELLS
R A I S I N G T H E S T A N D A R D
HW/SMP-6D RECTANGULAR
COOK ’N HOLD WARMER
HW/SMP-6D RECTANGULAR COOK ’N HOLD WARMER
I T E M N O .
WE L L S M A N U F A C T U R I N G
Features
• The tubular element, located inside the well,
is controlled by a positive-off thermostat and
allows for quicker heating.
• The positive-off thermostat is recessed in a
one-piece, drawn, front-mounted panel.
• Warming pan is deep-drawn, stainless steel
for maximum strength and durability and has
a 1/2” drain.
• Wellslok provides quick and easy installation
in stainless steel countertops.
• This warmer is designed for wet operation only.
• The HW/SMP-6D Cook ‘N Hold Warmer
is Underwriters Laboratories, Inc. LISTED and
meets NSF International standards.
• A one-year warranty against defects covers
parts and labor.
Wells HW/SMP-6D Built-In Cook ‘N Hold
Warmer is designed for efficiency. The tubular
immersion element allows for rapid heat transfer
into the water. Wells Cook ‘N Hold Warmers
quickly heat food from a refrigerated state to
serving temperature.
Specifications
Overall Dimensions: Inches MM
Width 14 3/4 375
Depth 23 1/2 597
Temperature Range: Fahrenheit Celsius
HW/SMP-6D 90º 32º
to 210º to 99º
Number of Thermostats: 1
Weights: Lbs. KG
Installed 23 10
Shipping 26 12
Accessories / Options
Adapter Top, to convert HW/SMP-6D to
hold three 4-quart insets, 21615
Adapter Top, to convert HW/SMP-6D to
hold one 7-quart inset and one 4-quart
inset, 21617
Adapter Top, to convert HW/SMP-6D to
hold one 7-quart and one 11-quart inset,
21621
Adapter Top, to convert HW/SMP-6D to
hold four 2 1/2-quart insets, 21624
Inset, 2 1/2-quart capacity with lid, 20773
Inset, 4-quart capacity with lid, 20774
Inset, 7-quart capacity with lid, 20587
Inset, 11-quart capacity with lid, 20908
Wellslok Extension Kit, designed for
countertops up to 1 1/2” thick, refer to
installation instructions, 22593
HW/SMP-6D

STD.4
R
E6070
R
LISTED
WELLS MANUFACTURING COMPANY
2 ERIK CIRCLE, PO BOX 280, VERDI, NV 89439 U.S.A. • USA PHONE: [phone] • FAX: [phone]
FOR ORDERS ONLY: [phone] • FAX: [phone] • www.wellsbloomfield.com
2001 WELLS MANUFACTURING • PRINTED IN THE U.S.A. • 2/01 • REV(C) • PART NO. 44805
MODEL
H W / S M P - 6 D R E C TA N G U L A R
C O O K ’N H O L D WA R M E R
DIMENSIONS: INCH
(MM)
WE L L S M A N U F A C T U R I N G
WELLS
(25)
1
(86)
3 3/8
(125)
4 15/16
(22)
7/8
(375)
14 3/4
(149)
5 7/8
(159)
6 1/4
(221)
8 11/16
(597)
23 1/2
(305)
12
(508)
20
ELEMENT
HEATING
IMMERSION
1/2 IN DRAIN NPT
MINIMUM CLEARANCE REQUIRED
UNIT TO NEAREST SURFACE
BACK SIDE BOTTOM FRONT
1 1 6 3/4 4 1/8
(25) (25) (171) (105)
NOTE: Specifications are subject to change without notice. See installation instructions prior to installing the unit.
This document is not for installation purposes.
H W / S M P - 6 D E L E C T R I C A L S P E C I F I C AT I O N S :
HW/SMP-6D 208 1350 6.5 SINGLE NONE
HW/SMP-6D 240 1800 7.5 SINGLE NONE
MODELS VOLTS WATTS AMPS PHASE POWER SUPPLY CORD