Whalen TEN2PST User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Manufacturing Page 1 Factory No. 14697
Date 2015-03-03 Rev. 1 Factory: CTHAUP
Tenison 2-pk Stools
Stock # TEN2PST
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED:
/
/

Stock # TEN2PST
Please call for replacement parts or assistance: 866-942-5362
Whalen Furniture Manufacturing Page 2 Factory No. 14697
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair
or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed
to meet your highest expectations. We guarantee that you will immediately see the value of our fine
furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State
to State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.
GENERAL INFORMATION, TIPS & TRICKS

Stock # TEN2PST
Please call for replacement parts or assistance: 866-942-5362
Whalen Furniture Manufacturing Page 3 Factory No. 14697
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Seat (2) B- Leg (8)
C- Long Stretcher (4) D-Short Stretcher (4)
(1) Ø5/16" x 2-1/2” Bolt (2) Lock Washer (3) Flat Washer
(16 +1 extra) (16+1 extra) (16+1 extra)
(4) 1-1/2” Wood Screw (16 +1 extra) Open-end Wrench (1)
Tools required: Open-end wrench (included) and Phillips screwdriver (not included).

Stock # TEN2PST
Please call for replacement parts or assistance: 866-942-5362
Whalen Furniture Manufacturing Page 4 Factory No. 14697
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Place one Seat (A) upside down on a flat, protected surface as shown.
3. Connect one Short Stretcher (D) between 2 Legs (B) as shown. Make sure the slant holes on the stretcher
will face the floor when the unit is turned upright.
4. Align and attach the leg assembly to the Seat (A) using four 2-1/2” Bolts (1), four Lock Washers (2) and
four Flat Washers (3) as shown. Tighten the bolts with the enclosed open-end wrench.
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damage to the thread, DO NOT over-tighten the nuts or bolts.
Flat Washer
(4 used in this step)
③
Lock Washer
(4 used in this step)
②
Ø5/16" x 2-1/2” Bolt
(4 used in this step) ①

Stock # TEN2PST
Please call for replacement parts or assistance: 866-942-5362
Whalen Furniture Manufacturing Page 5 Factory No. 14697
Assembly Instructions
5. Fit 2 Long Stretchers (C) to the mortise of the assembled Legs (B) with the slat holes facing up, as shown.
6. Connect the other 2 Legs (B) with one Short Stretcher (D).
7. Attach the leg assembly to the other end of Seat (A) and insert both Long Stretchers (C) into the mortises
of Legs (B) respectively. Insert four 2-1/2” Bolts (1) with Lock Washers (2) and Flat Washers (3) through
the corner blocks and securely screw into the Legs (B). As shown.
NOTE: DO NOT fully tighten all the bolts until the stool has been adjust and level all the legs so that
they do not wobble. Once adjusted then go back and tighten while making sure that the unit remains level.
Flat Washer
(4 used in this step)
③
Lock Washer
(4 used in this step)
②
Ø5/16" x 2-1/2” Bolt
(4 used in this step) ①