WHALETEQ DFS360 User manual

DFS360 |User Manual
WHALETEQ
DFS360 / DFS360D
User Manual
PC Software Version 1.0.1.18
Revision 2022-08-08

DFS360 |User Manual
1
Copyright © 2013-2022, All Rights Reserved.
WhaleTeq Co. LTD
No part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language or computer
language, in any form, or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written
permission of WhaleTeq Co. LTD.
Disclaimer
WhaleTeq Co. LTD. provides this document and the programs "as is"
without warranty of any kind, either expressed or implied, including, but
not limited to, the implied warranties of merchantability or fitness for a
particular purpose.
This document could contain technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will
be incorporated in future revisions of this document. WhaleTeq Co. LTD. is
under no obligation to notify any person of the changes.
The following trademarks are used in this document:
is a registered trademark of WhaleTeq Co. LTD
All other trademarks or trade names are property of their respective
holders.

DFS360 |User Manual
2
Contents
1Introduction.................................................................................. 6
1.1 Concept......................................................................................................6
1.2 Applications................................................................................................6
2Specification.................................................................................. 7
2.1 General Specifications................................................................................7
2.2 Compliance Specifications .........................................................................7
2.3 Energy Measurement Specifications .........................................................8
2.4 ECG Signal Specifications ...........................................................................8
3Instrument Familiarization......................................................... 9
3.1 Top .............................................................................................................9
3.2 Front...........................................................................................................9
3.3 Rear..........................................................................................................10
3.4 Left and Right Side ...................................................................................11
3.5 Wiring Diagram ........................................................................................12
3.5.1 Connection Diagram and Precautions ...................................................................12
4Getting Started............................................................................13
4.1 PC System Requirements.........................................................................13
4.2 Software Installation................................................................................14
4.3 USB Driver Installation.............................................................................14
4.4 Microsoft .Net Framework Installation....................................................15
4.5 PC Software and Firmware Update..........................................................16
5PC Software Operation ..............................................................16
5.1 Software Function Introduction...............................................................16
5.1.1 Function Buttons Operation.................................................................................19
5.1.2 Customize ECG Waveform (optional function) .......................................................24
5.2 PC Software Operation Instructions ........................................................28
5.3 Over Heat Warning and Function Protection ..........................................32
5.3.1 AP Display Status ................................................................................................32
5.3.2 DFS Status LED....................................................................................................33
5.3.3 Fan Behavior ......................................................................................................33
5.3.4 Over Heat Protection ..........................................................................................33
5.4 Optional Software Development Kit (SDK) ..............................................33

DFS360 |User Manual
3
5.4.1 Command Function.............................................................................................34
6Standalone Operation................................................................35
7Calibration and Validation.........................................................35
8Troubleshooting..........................................................................36
9Cautions........................................................................................36
10 Ordering Information.................................................................37
11 Package Contents........................................................................40
12 Revision History ..........................................................................41
13 Contact WhaleTeq ......................................................................41

DFS360 |User Manual
4
List of Tables
Table 1: General Specifications ......................................................... 7
Table 2: Compliance Specifications ................................................... 7
Table 3: Energy Measurement Specifications ................................... 8
Table 4: ECG Signal Specifications..................................................... 8
Table 5: AP Interface Function Introduction ................................... 16
Table 6: Setting List Introduction .................................................... 18
Table 7: Customize ECG Waveform Function Introduction............. 24
Table 8: Shock Result Introduction.................................................. 30
Table 9: Command Function............................................................ 34
Table 10: Ordering info. for DFS360................................................ 37
Table 11: Ordering info. for DFS360D ............................................. 37
Table 12: Optional DFS360 / DFS360D Paddle Box Set ................... 38
Table 13: Optional Software Add-On Pack...................................... 39
Table 14: Optional Tool ................................................................... 39
Table 15: Optional Calibration Service and Warranty Extension.... 39
Table 16: Package Contents for DFS360.......................................... 40
Table 17: Package Contents for DFS360D ....................................... 40
Table 18: Revision History ............................................................... 41

DFS360 |User Manual
5
List of Figures
Figure 1: Top Side of DFS360 / DFS360D........................................... 9
Figure 2: Front Side of DFS360 / DFS360D ........................................ 9
Figure 3: Rear Side of DFS360 / DFS360D........................................ 10
Figure 4: Left Side of DFS360 / DFS360D (Top: DFS360; Bottom:
DFS360D) ................................................................................. 11
Figure 5: Right Side of DFS360 / DFS360D....................................... 11
Figure 6: Wiring Diagram................................................................. 12
Figure 7: Correct Wiring Diagram of the AED Cable........................ 12
Figure 8: Correct Wiring Diagram of the USB Cable........................ 13
Figure 9: AP Interface ...................................................................... 16
Figure 10: Setting List ...................................................................... 18
Figure 11: Documents in the Folder................................................ 19
Figure 12: Waveform Details........................................................... 20
Figure 13: Set the Time Range and Display of Voltage or Current.. 20
Figure 14: Error Report Window ..................................................... 21
Figure 15: Set a Designated Range of Time..................................... 21
Figure 16: Check Desired Test Results for Analysis ......................... 22
Figure 17: Consistency and Availability Analysis (Top: The
Consistency of Shock Waveforms of Multiple DUTs; Bottom:
The Availability of a Single DUT).............................................. 23
Figure 18: Standard Waveforms...................................................... 23
Figure 19: Adjustable BPM, Frequency, and Amplitude ................. 23
Figure 20: License Activation........................................................... 24
Figure 21: ECG Waveform ............................................................... 24
Figure 22: Complete Customized Waveform Settings .................... 28
Figure 23: Select Test Items............................................................. 29
Figure 24: Shock Result.................................................................... 30
Figure 25: Shock Waveform Details ................................................ 30
Figure 26: High-Temperature Alert ................................................. 32
Figure 27: DFS360 / DFS360D Return to Normal Temperature ...... 32

DFS360 |User Manual
6
1 Introduction
1.1 Concept
WhaleTeq DFS360 / DFS360D is a multifunction testing device,
functioning as an ECG signal simulator and energy measurement
equipment for the AED and defibrillator manufacturing environment.
For ECG signal simulation, DFS360 / DFS360D simulates NSR as well as
various arrhythmias that may or may not need AED defibrillation.
Arrhythmia convert combination (ECG waveform before vs. after
defibrillation) is also available.
For energy measurement calculation, DFS360 / DFS360D distinguishes
multiple kinds of biphasic waveforms and monophasic waveforms,
which are what the majority of current AEDs and defibrillators deliver.
Capturing the characteristic points of each kind of waveform, DFS360
/ DFS360D is also capable of displaying the real defibrillation
waveforms.
These features can be consolidated into the computer software of
AED or defibrillator manufacturers. What’s more, DFS360D is designed
to withstand more intense defibrillation shocks over longer stretches; it
takes shocks at 15-second intervals, meaning a boost of testing capacity. All
in all, DFS360 / DFS360D is a durable tester to speed up AED or
defibrillator automatic production.
1.2 Applications
WhaleTeq DFS360 / DFS360D is suitable for AED or defibrillator
manufacturing automation. With SDK provided, User can integrate
the functions of DFS360 / DFS360D into the manufacturing execution
system of the AED or defibrillator manufacturer’s choice. Test results
from DFS360 / DFS360D are thus combined into the production
history of each AED.

DFS360 |User Manual
7
2 Specification
2.1 General Specifications
Table 1: General Specifications
Items
Specifications
Temperature
Operating: 0 °C ~ + 50 °C (+ 32 °F ~ + 122 °F)
Storage: -20 °C ~ + 60 °C (-4 °F ~ + 140 °F)
Humidity
10 % ~ 90 % non-condensing
Power
USB 3.0 Bus Power
Communications
USB Type-C connector
Operation
Modes
Remote (PC Software via API and SDK)
Mechanical
Housing: ABS Plastic
Size (L x W x H): 19.0 x 12.5 x 6.0 (cm)
Weight: DFS360: 665g / DFS360D: 815g
2.2 Compliance Specifications
Table 2: Compliance Specifications
Items
Specifications
Safety Standards
CE: IEC/EN61010-1:2010 + A1:2016; Pollution
degree 2
61010-2-030:2017
Electromagnetic
Compatibility
Standards (EMC)
CE: EN61326-1
FCC: EMC P15B

DFS360 |User Manual
8
2.3 Energy Measurement Specifications
Table 3: Energy Measurement Specifications
2.4 ECG Signal Specifications
Table 4: ECG Signal Specifications
Items
Specifications
Ventricular Fibrillation -
Coarse
Vp-p = 3 mV
Ventricular Fibrillation -
Fine
Vp-p = 0.5 mV
Ventricular Tachycardia
(≒180BPM)
Vp-p = 3 mV
Ventricular Tachycardia
Plus (≒234 BPM)
Vp-p = 3 mV
Atrial Fibrillation
Vp-p = 1.2 mV
Items
Specifications
Maximum Energy
Range: Up to 600 J
Accuracy: ±1 % of reading ±1 J for up to 360J;
±1 % of reading ±1 J, typical for 360J ~ 600J
Voltage
Range: Up to 3000 V
Accuracy:
±(1% of reading + 1V) for 450V ~ 3000V & -450V ~ -3000V;
± (1% of reading + 2V) for -450V ~ 450V
Load Resistance
Resistance: 50Ω
Pulse Width
Range: 1.0 ~ 48.0 ms
Accuracy: ±0.05 ms
Sample rate
250 kHz (4 μs sample)
Maximum Average
Power
DFS360: 12 W, for 1 defib. Pulse of 360 J every 30 sec.
DFS360D: 24 W, for 1 defib. pulses of 360 J every 15 sec.

DFS360 |User Manual
9
Items
Specifications
Asystole
Vp-p = 0.03 mV
User-defined Pattern
(Max. 5K Sample Rate)
Up to 10 sets with 100 seconds max. each
set
Normal Sinus Rhythm (NSR): 30 to 240 (increment by 1) BPM
Amplitude range: Vp-p 0.5 ~ 5.0mV, step 0.5 mV
3 Instrument Familiarization
3.1 Top
Figure 1: Top Side of DFS360 / DFS360D
3.2 Front
Figure 2: Front Side of DFS360 / DFS360D
A

DFS360 |User Manual
10
A. AED Input Ports: Use AED cables provided to connect device
under test (an AED or a defibrillator) to the DFS360 / DFS360D.
3.3 Rear
Figure 3: Rear Side of DFS360 / DFS360D
B. USB Port: Use to supply power. Also, it can be used to connect
to the computer for sending commands and transferring data.
C. Status LED: Indicate the working state of DFS360 /DFS360D.
Mode
Normal
Heat Alert
Standalone Operation
Green light
flashes every 2
seconds.
Red light flashes
every 2 seconds.
AP Connected (ECG
Playing)
AP Connected (ECG
NOT Playing)
Green light always
on.
Red light always
on.
B
C

DFS360 |User Manual
11
3.4 Left and Right Side
Figure 4: Left Side of DFS360 / DFS360D (Top: DFS360; Bottom: DFS360D)
Figure 5: Right Side of DFS360 / DFS360D
D. Air Inlet: Allow ventilation during long hours of operation.
E. External Load Box Port: Connect this port to the external load
box with various resistance values for tests.
F. Air Outlet: Allow ventilation during long hours of operation.
D
F
E
D

DFS360 |User Manual
12
3.5 Wiring Diagram
Figure 6: Wiring Diagram
3.5.1 Connection Diagram and Precautions
1. Connect the AED cable to DFS360 / DFS360D.
。Do not put the AED cable on DFS360 / DFS360D main console.
。The AED cable should not twist together.
Figure 7: Correct Wiring Diagram of the AED Cable
2. After connecting the AED cable, connect DFS360 / DFS360D and
PC / Laptop with the USB cable.
。The USB cable and PC / Laptop should not be placed near the
AED cable.
。The USB cable should not twist with the AED cable.

DFS360 |User Manual
13
。The USB cable should not be placed on DFS360 / DFS360D main
console.
Figure 8: Correct Wiring Diagram of the USB Cable
3. Make sure the output voltage of the USB cable is between
4.75V ~ 5.25V (The minimum input voltage that DFS360 /
DFS360D can work is 4.5V).
4. Open AP “WhaleTeq DFS360 Test System” on PC / Laptop .
4 Getting Started
4.1 PC System Requirements
DFS360 software uses a Windows PC to connect and control DFS360 /
DFS360D via USB module.
PC requirements:
- Windows PC (Windows 7 or later, suggest to use the genuine
version)
- Microsoft .NET 4.0 or higher
- Administrator access (essential for installing software, driver, and
Microsoft .Net Framework)
- 1.5 GHz CPU or higher
- 1GB RAM or higher
1
1
Relative to normal PC processing, there is no special use of PC speed. However, there has been
noted a slow increase in system RAM usage over long periods of time up to 30-40MB (related to MS
Windows “garbage collection”). PCs with only 512MB or less installed and are running several other
programs (in particular, Internet Explorer), may exceed the available RAM, requiring access to the

DFS360 |User Manual
14
- USB port
4.2 Software Installation
Please follow the steps below to download and execute DFS software.
1. Download DFS360 software from WhaleTeq’s website.
2. Open the file explorer and select the download location.
3. Double click on WhaleTeqDFS360.exe to execute DFS360 PC
software.
Note:
If DFS software can’t be executed properly, or this is the first time
using WhaleTeq’s product, please refer to the two sections below (4.3
and 4.4) to confirm that the USB driver and Microsoft .Net Framework
4.0 are both installed.
4.3 USB Driver Installation
If Windows Device Manager can’t recognize WhaleTeq’s product,
please follow the instructions below to install Microchip® USB Driver.
For Microsoft Windows 10
⚫As Windows 10 has built-in Microchip® USB Driver, there is no
need to install any drivers. It just takes a while for Windows
Device Manager to recognize and install the driver.
For Microsoft Windows 8 and Windows 8.1
⚫If Windows 8 and Windows 8.1 can’t recognize DFS360 /
DFS360D unit, please download “mchpcdc.inf” from WhaleTeq’s
website. This driver is provided by Microchip®, and is intended to
hard drive and dramatically impacting speed. In this case, streaming interruptions and other
problems may occur.

DFS360 |User Manual
15
be used with PIC microprocessors which have built-in USB
functions.
⚫As mchpcdc.inf provided by Microchip® does not contain a digital
signature, please disable the driver signature enforcement in
Windows 8 and Windows 8.1. Please click here to watch the
tutorial video.
⚫When the USB module is connected for the first time, select
Manual Installation, and point to the folder containing the above
file. Then, continue to follow the instructions to finish the
installation. There may be a warning that the driver is not
recognized by Windows®, and this can be ignored. Please click
here to watch the tutorial video.
For Microsoft Windows 7
⚫If Windows 7 can’t recognize DFS360 / DFS360D unit, please
download “mchpcdc.inf” from WhaleTeq’s website. This driver is
provided by Microchip®, and is intended to be used with PIC
microprocessors which have built-in USB functions.
⚫When the USB module is connected for the first time, select
Manual Installation, and point to the folder containing the above
file. Then, continue to follow the instructions to finish the
installation. There may be a warning that the driver is not
recognized by Windows®, and this can be ignored. Please click
here to watch the tutorial video.
4.4 Microsoft .Net Framework Installation
WhaleTeq’s software is developed based on Microsoft .Net
Framework 4.0. If DFS software fails to execute properly, please check
whether Microsoft .Net Framework 4.0 or a higher version was
installed in the operating system.
If the PC hasn’t installed Microsoft .Net Framework 4.0 or a higher
version, please download it from Microsoft’s website. Please click
here to watch the tutorial video (from 2:17).

DFS360 |User Manual
16
4.5 PC Software and Firmware Update
User can download the latest software from WhaleTeq’s website. If
User cannot update the DFS software, please contact WhaleTeq’s
service team ([email protected]).
5 PC Software Operation
5.1 Software Function Introduction
When opening DFS360 AP, User will see the figure below on the
screen.
Figure 9: AP Interface
Table 5: AP Interface Function Introduction
Item
Name
Description
A
Add
Add one or more ECG waveform(s) to
the Test List.
B
A
F
L
G
E
I
H
K
C
D
J

DFS360 |User Manual
17
Item
Name
Description
B
Save
Save the designated test items as a file.
C
Recall
Open the saved file of test items.
D
Reset
Reset all test items.
E
Test List
Show all test items added.
F
Loop
After clicking Loop, the test items will
be running in a loop.
G
Start
Start the test with playing designated
test items.
After the test starts, this button will
turn into Stop.
H
ECG Waveform
Display the playing ECG waveform.
I
Shock Waveform
Display the shock waveform gave by
the DUT.
J
Shock Information
Display the energy (in Joules),
parameters, and characteristic points
of the shock.
K
Settings
Check for updates, set the customized
ECG waveforms, choose naming
methods of test results, and select the
language, etc.
L
Function Buttons
Top to bottom:
Folder: Open the folder storing test
results in the local computer.
Waveform Details: Display positions of
the parameters and characteristic
points on the defibrillation waveform.
Graph Setup: Set the time range and
display of voltage or current on Shock
Waveform.
Waveform Error Report: Allow users to
report issues to WhaleTeq in case of
software errors.
Consistency and Availability Analysis:
Superimpose multiple test waveforms
to confirm the consistency of quality
on multiple DUTs or the availability of a
single DUT.

DFS360 |User Manual
18
Item
Name
Description
Standard Waveforms: Provide Sine,
Square, and Triangle for testing with
adjustable BPM, frequency, and
amplitude.
Note:
Below list the provided ECG waveforms with Adult (max. 3kV) mode and
Child (max. 1.5kV) mode. Only NSR with adjustable BPM, frequency, and
amplitude.
Ventricular Fibrillation –Coarse
Ventricular Fibrillation –Fine
Ventricular Tachycardia
Ventricular Tachycardia Plus (the faster VT)
Atrial Fibrillation
Asystole
NSR
Right-click the Settings button and the settings below will show.
Figure 10: Setting List
Table 6: Setting List Introduction
Item
Name
Description
M
Check for Updates
Check whether the DFS360 AP is the
latest version.
M
N
P
O

DFS360 |User Manual
19
Item
Name
Description
N
Customize ECG
Waveform
Settings for customized ECG
waveforms. (For more information,
please refer to sec. 5.1.2)
O
Naming results
Set the naming methods of test
results: Default, Barcode Reader, and
Manual Key-in.
Note:
The barcode reader works with specific
software and needs a separate
purchase. After the purchase, users
will receive an Activation Key to
activate this function.
P
Language
Switch the language of the DFS360 AP.
Note:
The languages include Traditional
Chinese, Simplified Chinese, and
English.
5.1.1 Function Buttons Operation
Function Buttons on the right of DFS360 / DFS360D AP screen will be
elaborated from top to bottom:
1. Folder
After every test, the system will automatically save the test result in three
documents, including the document of raw data, the document of
parameters and characteristics points, and the document of the waveform
figure. Users can find the documents after clicking the Folder button.
Figure 11: Documents in the Folder