WHALETEQ WAIOT-N User manual

1
© 2022 WhaleTeq All Rights Reserved
Verify and Validate Your Product Design with Ease
Quick Start Guide
Released: 2023-01-13
WAIOT-N
AED NB-IoT Module

2
© 2022 WhaleTeq All Rights Reserved
◼Hardware Overview –Main Unit
◼Hardware Overview –IoT Bridge
◼Test Software –Before starting the tests
◼Test Software –Buzzer Testing
◼Test Software –Cabinet Testing
◼Test Software –AED Status Detection
◼Test Software –SIM Status
◼Test Software –Misc. (SD card) and Save Test Reports
◼Establish the connection between the WAIOT-N and WhaleTeq AED AIMS Cloud CMS
◼Test the connection between the WAIOT-N and WhaleTeq AED AIMS Cloud CMS

3
© 2022 WhaleTeq All Rights Reserved
Top View
Front View
Reset Button
2
Hardware Overview –Main Unit
Use a USB to UART
cable to connect the
main unit to a
computer for on-site
inspection and
maintenance
AP Port 1
Link LED
3
SD Card Slot
5
SIM Card Slot
6
IoT Bridge Connection Terminal
7
DC 5V Power Jack
8
Power LED
4
Indicates the connection
status between the main
unit and the WhaleTeq
AIMS Cloud CMS
Bottom View

4
© 2022 WhaleTeq All Rights Reserved
Connect to the power
supply of the buzzer.
Applicable voltage range:
DC 9V~12V
Hardware Overview –IoT Bridge
Buzzer
Connection Terminal
1
Main Unit
Connection Terminal
5
Power
Connection Terminal
4
Front View Bottom View
AED Weight Sensor
Connection Terminal
2
Door Sensor
Connection Terminal
3

5
© 2022 WhaleTeq All Rights Reserved
Test Software –Before starting the tests
①Connect a computer to the WAIOT-N
main unit using a USB to UART cable
and make sure that the computer
connects to the Internet.
②Activate the WAIOT-N test software.
③Check the serial number of the
connected WAIOT-N and the IMSI
serial number of the SIM card are
correct.
④Enter the test location and tester.
1 2
3 4

6
© 2022 WhaleTeq All Rights Reserved
Please test in the following order, and before performing
each test item, make sure that the cabinet is closed and
the AED is in the cabinet.
①Manual On
Click the TEST button.
◆Successfully activate the alarm buzzer: click (Y)
◆Fail to activate the alarm buzzer: click (N)
②Manual Off
Click the TEST button to turn off the alarm buzzer.
◆Successfully turn off the alarm buzzer: click (Y)
◆Fail to turn off the alarm buzzer: click (N)
③Auto Off
Click the TEST button, and the alarm buzzer will keep ringing for 1
minute and then turn off automatically.
◆Automatically turn off: click (Y)
◆Fail to automatically turn off: click (N)
Test Software –Buzzer Testing
3
1
2

7
© 2022 WhaleTeq All Rights Reserved
Test Software –Cabinet Testing
3
1
2
Please test in the following order:
①Battery Voltage
Please use the WhaleTeq DFS200 tester with a battery measurement probe to
measure the voltage of the cabinet battery and manually enter the test result.
②AED Relay Status
After clicking the Test button, please press or release the AED weight sensor,
and check whether the corresponding result appears on the window (press:
AED in place; release: AED taken away).
◆Correct status: click (Y)
◆Incorrect status: click (N)
③Door Relay Status
After clicking the Test button, please press or release the door sensor,
and check whether the corresponding result appears on the window (press:
Cabinet enclosure door closed; release: Cabinet enclosure door open).
◆Correct status: click (Y)
◆Incorrect status: click (N)

8
© 2022 WhaleTeq All Rights Reserved
Test Software –AED Status Detection
3
1
2
Please test in the following order, and the test results will appear in
the window.
①Self Checking
◆Click the TEST button to play the AED self-test sound.
②Low Power
◆Click the TEST button to play the alert sound of AED low battery.
③PCB Error
◆Click the TEST button to play the alert sound of AED anomalies.
Note: For the 3 test items, after the WAIOT-N successfully detects the sound, the software will
determine the result as PASS; if it fails to detect, the software will continue to play the
sound.

9
© 2022 WhaleTeq All Rights Reserved
Test Software –SIM Status
1
2
Status Description
1
Idle
The WAIOT
-N has no action.
2
SIM Not Ready
The
SIM card is not inserted into the WAIOT-N.
3
SIM Detected
The
SIM card is detected.
4
APN Connecting
The SIM card has not connected to the base station.
5
AWS Connecting
The SIM card has not connected to the server.
6
AWS Connected
The connection is established and operating properly.
This test item shows the network connection status of the WAIOT-N.
①Signal Strength
◆Shows the value of current signal strength (range: -51 ~ - 113dBm). A smaller value
represents that the signal is weaker.
◆If the value is less than -85dBm, a poor signal strength warning will pop up, and the
test result will be determined as FAIL.
②Connection Status
Note:
1. The connection time for this test item is about 10 minutes.
2. Due to the firmware settings, there will be disconnections and
reconnections in the first 5~10 minutes of connection. After the "AWS
Connected" status appears, please wait for 1~2 minutes to determine
whether the connection status is stable.

10
© 2022 WhaleTeq All Rights Reserved
Test Software –Misc. (SD card) and Save Test Reports
①Misc. (SD card)
Click the TEST button to perform a read/write test on the SD card.
1
2
Test Result Description and Solutions
PASS
This function and the SD card are operating
properly.
FAIL
(one time)
Record
and report the situation to WhaleTeq
, and
then repeat the test.
FAIL (more than five times)
Please reinsert the SD card, or replace it with a
new one.
②Save Test Reports
◆Enter a user-defined report number and click the Save button to save and export
the test report to create an installation or test record.
◆Click the folder button ( ) to bring up the folder where the test report is.

11
© 2022 WhaleTeq All Rights Reserved
①Log in to the AIMS Cloud CMS and select Product sales MGT.
②Select Sales MGT.
③In the Equipment No. field, enter the serial number of the AED that is newly installed with the WAIOT-N, and click Search.
④Click Update of the corresponding AED to bring up Modify equipment sales information window. (see next page)
Establish the connection between the WAIOT-N and WhaleTeq AED AIMS Cloud CMS
3
1
2 4

12
© 2022 WhaleTeq All Rights Reserved
①In the Modify equipment sales information
window, scroll the Basic information tab to
the bottom and click Next step to go to the
Monitor information tab.
②Click Add to bring up the Choose monitor
window, and check the AED status and AED
cabinet status, then click Confirm. These
two items will appear on the Monitor
information tab.
③Click Edit of AED status and AED cabinet
status to bring up the Modification of
monitor window. (see next page)
1
2
3
Establish the connection between the WAIOT-N and WhaleTeq AED AIMS Cloud CMS

13
© 2022 WhaleTeq All Rights Reserved
①In the Modification of monitor
window, enter the serial number
of WAIOT-N in the IoT Number
field and click Confirm to save.
The serial number will appear on
the IoT Number field in the
Monitor information tab.
Click Confirm in this tab to go to
the next tab.
②In the Accessories information
and Supplies information tabs, if
no information needs to be
modified, click Confirm to
complete the setting of WAIOT-N
on the AIMS Cloud CMS.
1
2
Establish the connection between the WAIOT-N and WhaleTeq AED AIMS Cloud CMS

14
© 2022 WhaleTeq All Rights Reserved
①Select Monitoring.
②Select Equipment data MGT.
③In the Equipment No. field, enter the serial number of the AED that completed the WAIOT-N settings on the AIMS Cloud CMS,
and click Search.
④Click Detail of the corresponding AED to bring up the Equipment data details window.
⑤Please ask the field inspector to open and close the door of the AED cabinet to test whether the AIMS Cloud CMS receives the
status sent by the WAIOT-N in real time. (Open: "Chassis open, AED in place"; Close: "Normal")
1
2
3
4
Test the connection between the WAIOT-N and WhaleTeq AED AIMS Cloud CMS
5

15
© 2022 WhaleTeq All Rights Reserved
Verify and Validate Your Product Design with Ease
www.whaleteq.com
[e-mail]
8F., No. 125 Songjiang Rd., Zhongshan Dist., Taipei City 104474, Taiwan
Copyright © 2013-2023, All Rights Reserved.
WhaleTeq Co. LTD
[phone]
[phone]
is a registered trademark of WhaleTeq Co. LTD.
All other trademarks or trade names are the property of their respective holders.
Verify and Validate Your Product Design with Ease
All information, documentation, firmware, software
utilities, and specifications are subject to change
without prior notification by the manufacturer.