Wood Stone PHOENIX 3030 User manual

PHOENIX OVEN
Gas-Fired Stone Hearth Oven
Revised September 2009
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
www.woodstone-corp.com
PHOENIX 3030
WS-PX-3030-RFG
PHOENIX 4343
WS-PX-4343-RFG, WS-PX-4343-RFG-W
PHOENIX 4355
WS-PX-4355-RFG, WS-PX-4355-RFG-W
Installation and
Operation Manual

TABLE OF CONTENTS
PHOENIX OVEN --------------------------------------------------------------------------------- 2
WS-PX-3030 SPECIFICATIONS ------------------------------------------------------------------ 4
WS-PX-4343 SPECIFICATIONS ------------------------------------------------------------------ 5
WS-PX-4355 SPECIFICATIONS ------------------------------------------------------------------ 6
INSTALLATION CLEARANCES -------------------------------------------------------------------- 7
MOVING THE OVEN ----------------------------------------------------------------------------- 8
EXPLODED PARTS VIEW------------------------------------------------------------------------ 11
ASSEMBLY ------------------------------------------------------------------------------------ 12
ASSEMBLY-CONNECTIONS --------------------------------------------------------------------- 18
DISASSEMBLY--------------------------------------------------------------------------------- 20
VENTING -------------------------------------------------------------------------------------- 23
OVEN STARTUP-------------------------------------------------------------------------------- 24
DAILY OPERATION ----------------------------------------------------------------------------- 25
DAILY MAINTENANCE -------------------------------------------------------------------------- 26
SAFETY CONSIDERATIONS --------------------------------------------------------------------- 27
CONTROLLER --------------------------------------------------------------------------------- 28
120 V ELECTRICAL DIAGRAM ------------------------------------------------------------------ 29
240 V ELECTRICAL DIAGRAM ------------------------------------------------------------------ 30
LIMITED WARRANTY --------------------------------------------------------------------------- 31
1
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
TABLE OF CONTENTS
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009

WS-PX-4343-RFG-(NG OR LP), WS-PX-3030-RFG-(NG OR LP),
WS-PX-4343-RFG-(NG OR LP)-W, WS-PX-3030-RFG-(NG OR LP)-W
INSTALLATION AND OPERATION MANUAL
FOR THE WOOD STONE PHOENIX
THIS APPLIANCE IS FOR PROFESSIONAL USE BY QUALIFIED PERSONNEL. THIS APPLIANCE
MUST BE INSTALLED BY QUALIFIED PERSONS IN ACCORDANCE WITH THE REGULATIONS
IN FORCE. THIS APPLIANCE MUST BE INSTALLED WITH SUFFICIENT VENTILATION TO
PREVENT THE OCCURRENCE OF UNACCEPTABLE CONCENTRATIONS OF SUBSTANCES
HARMFUL TO HEALTH IN THE ROOM IN WHICH IT IS INSTALLED. THIS APPLIANCE NEEDS
AN UNOBSTRUCTED FLOW OF FRESH AIR FOR SATISFACTORY COMBUSTION AND MUST
BE INSTALLED IN A SUITABLY VENTILATED ROOM IN ACCORDANCE WITH CURRENT
REGULATIONS. THIS APPLIANCE SHOULD BE SERVICED BY QUALIFIED PERSONNEL AT LEAST
EVERY 12 MONTHS, OR SOONER IF HEAVY USE IS EXPECTED.
!
NATURAL GAS OR PROPANE FUELED STONE HEARTH OVEN
2
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
PHOENIX OVEN
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009
PHOENIX OVEN

WARNING: This product must be installed by a Licensed Plumber or Gas Fitter when installed within the
Commonwealth Of Massachusetts.
WOOD STONE PHOENIX GAS OVEN INSTALLATION AND OPERATING INSTRUCTIONS
DO NOT THROW THIS MANUAL AWAY
RETAIN THIS MANUAL FOR FUTURE REFERENCE: Additional copies of this manual and prompt responses to
service/maintenance questions are available from Wood Stone @ 1-800-988-8103.
IMPORTANT: Consult your local gas supplier for a statement outlining a procedure to be followed in the event
you smell gas. Post the statement in a prominent location.
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this
or any other appliance. Also, always keep the area under and around this appliance free and clear of any
and all combustible materials.
IT IS RECOMMENDED THAT THIS OVEN BE INSTALLED, MAINTAINED AND SERVICED BY AUTHORIZED
PROFESSIONALS.
WARNING: Improper installation, adjustment, alteration, service or maintenance can result in property
damage, injury or death. Read the installation, operation and maintenance instructions thoroughly before
installing or servicing this equipment.
3
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
PHOENIX OVEN
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009

Electrical
Specify AC Voltage, 1 amp, 50/60 Hz
See Data Plate on oven.
All utility connections made on the
back of the oven control box. Remove
front or rear panel for access, use
utility knockouts (provided) to route
gas and electrical supplies.
VENTING INFORMATION
The Phoenix should be vented using an approved
chimney, or an exhaust hood constructed and
installed in accordance with all relevant local and
national codes. Phoenix models with a -W in the
model number must be vented in accordance with
all regulations pertaining to solid fuel appliances.
Top View
Side View
Front View
Rear View
Unit Shipping Weight:
499 Kg
UTILITIES SPECIFICATIONS
Gas-3/4 inch gas inlet (female threaded)
42,000 BTU Natural Gas Supply OR
35,000 BTU Propane (LP) Supply
4
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
WS-PX-3030 SPECIFICATIONS
WS-PX-3030 SPECIFICATIONS

Unit Shipping Weight:
953 Kg
UTILITIES SPECIFICATIONS
Gas-3/4 inch gas inlet (female threaded)
80,500 BTU Natural Gas Supply OR
68,000 BTU Propane (LP) Supply
Electrical
Specify AC Voltage, 1 amp, 50/60 Hz
See Data Plate on oven.
All utility connections made on the
back of the oven control box. Remove
front or rear panel for access, use
utility knockouts (provided) to route
gas and electrical supplies.
VENTING INFORMATION
The Phoenix should be vented using an approved
chimney, or an exhaust hood constructed and
installed in accordance with all relevant local and
national codes. Phoenix models with a -W in the
model number must be vented in accordance with
all regulations pertaining to solid fuel appliances.
Top View
Side View
Front View
Rear View
5
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
WS-PX-4343 SPECIFICATIONS
WS-PX-4343 SPECIFICATIONS

Top View
Front View
Side View
Rear View
Unit Shipping Weight:
1134 Kg
UTILITIES SPECIFICATIONS
Gas-3/4 inch gas inlet (female threaded)
80,500 BTU Natural Gas Supply OR
68,000 BTU Propane (LP) Supply
OG models see Equipment Data Plate
Electrical
Specify AC Voltage, 1 amp, 50/60 Hz
See Data Plate on oven.
All utility connections made on the
back of the oven control box. Remove
front or rear panel for access, use
utility knockouts (provided) to route
gas and electrical supplies.
VENTING INFORMATION
The Phoenix should be vented using an approved
chimney, or an exhaust hood constructed and
installed in accordance with all relevant local and
national codes. Phoenix models with a -W in the
model number must be vented in accordance with
all regulations pertaining to solid fuel appliances.
6
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
WS-PX-4355 SPECIFICATIONS
WS-PX-4355 SPECIFICATIONS

CLEARANCES
a. The Wood Stone Phoenix oven should have a minimum 1-inch (2.54 cm) clearance to combustibles from all sides,
6-inch (15.2 cm) clearance to combustibles from the top, and 6-inch clearance (15.2 cm) from the flue collar.
If building a facade that will contact the oven, use completely non-combustible materials. Any facade wall built above or
6-inches (15.2 cm) to either side of the doorway must be of non-combustible construction. Please note that standard drywall
(or sheet rock) is considered a limited combustible. Any walls perpendicular to the front of the oven in the area 30 inches
(76.2 cm) to either side of the doorway and 36 inches (91.4 cm) in front of the oven should have a non-combustible surface.
b. The oven should be installed on a non-combustible floor surface. The non-combustible floor surface must extend 36
inches (91.4 cm) in front of and 30 inches (91.4 cm) to either side of the oven doorway.
IF THIS OVEN IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THESE
INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF OVEN RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED
CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPORTANCE THAT THIS OVEN
BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.
!
WARNING: Installation and servicing of this product could expose you to glasswool/ceramic
fibers as well as Calcium Silicate dust. ALWAYS WEAR RESPIRATORY AND EYE PROTECTION
WHEN INSTALLING OR SERVICING THIS APPLIANCE. Please read this entire manual before you
install the oven. Failure to follow instructions may result in property damage, bodily injury
or even death. Contact your local building or fire officials about restrictions and installation
inspection in your area.
6-inches
(15.2 cm)
Hatched area must be left
accessible and unobstructed
after installation for air
intake and routine service
of the oven burner.
6-inches
(15.2 cm)
1-inch (2.54 cm)
minimum side
clearance to
combustible
construction
Maintain 6-inch
(15.2 cm) clearance
from the exhaust
transition.
7
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
INSTALLATION CLEARANCES
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009
INSTALLATION CLEARANCES

If you received your Phoenix oven disassembled, go to page 12.
If you received your Phoenix oven fully assembled, but need to disassemble the oven to move it through a narrow door
or passageway, go to page 20.
If you received your Phoenix oven fully assembled, the oven can be moved into place with a pallet jack using
the LOWER forklift pockets. If the oven is to be installed against a wall, you may need to leave access to the
back of the oven to complete the utility connections.
CAUTION: The 3030 model Phoenix oven weighs approximately 499 kg. The 4343 model Phoenix oven weighs
approximately 953 kg. The 4355 model Phoenix oven weighs approximately 1134 kg. The oven is very top-heavy.
IF THE OVEN TIPS IT CAN CAUSE SEVERE INJURY OR DEATH! NEVER ATTEMPT TO USE A HAND TRUCK TO MOVE
THE OVEN! The oven should only be moved using a Pallet Jack on a LEVEL FLOOR. If the oven must be moved
over an inclined surface, a forklift or other suitable means should be employed. If the installer does not have
the equipment or experience required to move the oven safely, we recommend you secure the services of a
qualified rigging company.
Make sure the pallet jack wheels do not contact the underside of the fork pocket when lifting to avoid damaging
the stand.
8
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
MOVING THE OVEN
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009
MOVING THE OVEN

1. Use a forklift or other suitable lifting means to
set the oven body onto blocks as shown. If the
oven has the optional decorative logset, remove
it before tipping the oven.
2. Install the side pieces of the tipping
assembly.
3. Bolt the side piece to the oven as shown,
and attach the cross-piece using the hardware
provided.
Install a clevis ring in the top hole of each side
piece of the tipping assembly. Use these for
attachment of a lifting strap or chain.
If you received your oven disassembled, and you don't need to tilt the oven to move it through a door or narrow passageway,
refer to the exploded parts diagram on page 11, and go to page 12 for assembly instructions.
If you received the oven disassembled and need to move it through a narrow door or passageway, follow the instructions
below...
Cut away view
bolt
If your oven was originally shipped assembled, the optional lifting system is available from Wood Stone.
9
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free [phone]
Tel [phone]
Fax [phone]
[e-mail] or visit www.woodstone-corp.com
Phoenix Installation and Operation Manual
MOVING THE OVEN
An ongoing program of product improvement may require us to change
specifications without notice.WS-PX-3030, WS-PX-4343, WS-PX-4355
Revised September 2009