Yale 5300LN Grade 2 User manual

3. Install latch.
Insert latch in door. (Be sure bevel
edge of bolt faces strike plate.)
Attach with two screws supplied.
2. Drill door.
A. Drill 2-1/8" (54mm) dia. hole thru
the door. Cut notches as shown on
template. See note. (Except
Dummy Trim)
B. Drill 1" (26mm) dia. hole in edge of
door. Mortise for latch front 1-1/8"
(29mm) wide x 2-1/4" (57mm) high
x 5/32" (4mm) deep. (Except
Dummy Trim)
C. Drill two (2) 5/16" (8mm) dia.
holes thru door. See note.
D. Drill pilot holes for latch
screws. 7/64" (2.5mm) dia.
(Except Dummy Trim)
Note: To avoid splintering wood
doors, drill holes (A) and (C) from
both sides of the door.
D
B
1. Mark door.
Mark horizontal line across edge of
door for centerline of lock at desired
installation height. Fold template over
edge of door, centering on horizontal
line. Mark centers of holes at proper
backset.
For beveled and square edge doors,
mark both sides of the door.
Note:
Be sure to verify backset before
marking & drilling door.
5300LN Grade 2 or 4700LN Grade 1
Cylindrical Lever Locksets
Installation Instructions
Door
Marker
4. Unpack lock.
Attention Installer
Installation of cylindrical locks and latches must be through
bolted in all doors. If installation instructions are not followed this
may result in damage to the lock and void the factory warranty.
Any retrofit or other field modification to a fire rated opening can
potentially impact the fire rating of the opening, and Yale Locks &
Hardware makes no representations or warranties concerning
what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or
specifying and installing a new fire-rated opening, please consult
with a code specialist or local code official (Authority Having
Jurisdiction) to ensure compliance with all applicable codes and
ratings.
Tools Required
• 2-1/8" (54mm) hole saw
• 1" (26mm) boring bit
• 5/16" (8mm) drill bit
• 7/64" (2.5mm) drill bit
• Chisel & hammer
• #2 phillips screw driver
• Handle removal tool (supplied)
• 3/8" or 1/2" drill
IMPORTANT: The accuracy of the door preparation is
critical for the proper functioning and security of this lever
handle lock. Misalignment can cause premature wear and
tear and a lessening of security.
Outside Assembly
(stays assembled)
Bushing
Inside Rose
Support Assembly
Through Bolts
Inside Lever
Handle
An ASSA ABLOY Group brand
80-9150-0060-010 (11-16)

2
Latch Retractor engages
bolt tail(s)
Lockbody
Frame engages latchcase
Insert lockbody into door from outside making sure that
lockbody frame hooks latch case and retractor engages
bolt tail(s). DO NOT FORCE. (If lockbody does not
engage latch easily, check door preparation for errors.)
7. Install inside components.
A. Slide inside rose support assembly onto lockbody
and tighten through bolts.
B. Place black plastic bushing over push/turn button.
C. Place rose scalp on rose support assembly aligning the
dimple with the notch. Rotate the rose scalp clockwise
to lock. Note: Repeat on outside rose if necessary.
D. Install lever handle. For double cylinder functions,
install the inside cylinder and lever as shown on the
next page.
Machine Screw
Inside Rose
Support Assembly
Set Screw Hole
Push/Turn Button
8. Strike installation (Wood Frames Only).
A. Close door and mark a horizontal line from the center of
the template to the frame of the door.
B. Measure half the thickness of the door. Mark this same
distance with a vertical line starting from the stop side of
the frame and where both lines cross. Make a 1 inch
(26mm) diameter hole and 1/2 inch (13mm) in depth.
C. Align the holes of the strike with the vertical line. Trace the
outline of the strike and mortise with 1/16 inch (1.6mm)
depth. Attach the strike with two screws (provided).
STRIKES
371
Standard Strike Box
14-5301-1033
Attaching Screws
81-2012-0416
#8-8-32x3/4"
Attaching Screws
81-2012-0620
#12-12-24x1"
497
Optional Strike Box
#202
STOP
TEST THE OPERATION OF THE LOCKSET
Cycle the lock in both the locked and unlocked positions. If lock
functions smoothly when door is open, but binds when closed,
check door and frame alignment. If problems are found see
Troubleshooting on page 3.
6. Install lock.
5. Adjust lock for door thickness (if necessary).
(Lock is packed preadjusted for 1-3/4" (44mm) doors. Available for 2-1/4" (57mm) doors upon request.)
To Adjust for Thicker Door
A. Remove two (2) screws from outside rose.
B. Slide outside rose away from lock body.
C. Adjust rose plate to desired door thickness per illustration at right.
D. Fasten outside rose to lock body with two (2) screws.
2" door
1-3/4" door
C
Slide plate
to disengage
2-1/4" door
A
B
Rose Scalp
Bushing
Inside Lever
An ASSA ABLOY Group brand
80-9150-0060-010 (11-16)

Door Must Not Bind
Door Must Not Sag
Door Must Not Be Warped
Door Must Swing Freely
Troubleshooting
1. Check door.
2. Check hinges. They should not be loose or have excessive wear on
knuckles.
3. Latchbolt will not deadlock.
Either strike is out of line or gap between door and jamb is too great.
Realign strike or shim strike out towards flat area of latchbolt.
4. Latchbolt does not retract or extend properly.
Latchbolt tail and retractor not properly positioned.
A. Remove lockset. Look through 2-1/8" hole and verify latchbolt tail
centered between top and bottom of hole.
B. Remove latchbolt and insert lockset. Look through latch hole and
verify retractor mouth centered in hole. Adjust outside rose plate if
not. (See #5 on page 2)
C. Rebore holes if necessary to line up retractor and tail.
3
(Note: Cylinder and Sleeve must be properly installed or
the security of the lock will be compromised.)
DUMMY TRIM INSTALLATION
Secure the Rose Support assembly to the door using screws
and washers provided and install the rose scalp and inside
lever.
Machine Screws
Inside Rose
Support Assembly
Rose Scalp
Inside Lever
Washers
A. Insert key and rotate 45° counterclockwise.
B. Depress retainer with tool provided.
C. Slide lever off lock. (Also applies to inside
lever of 5321LN or 4721LN Function).
This lockset is designed to provide the highest standard of product quality and performance. Care should be
taken to insure a long-lasting finish. When cleaning is required use a soft,damp cloth. Using lacquer thinners,
caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
Finish Care
TO REMOVE CYLINDER HANDLE
TO REPLACE OR INSTALL CYLINDER
Tailpiece
Cylinder Sleeve
Yale Cylinder
A. Remove the sleeve from inside the shank or
from the old cylinder.
B. Slide cylinder into sleeve.
C. Rotate key 45° counterclockwise. Depress retainer
plate, push the handle onto the shank until fully
seated. Pull on handle to ensure properly seated.
5328LN, 5329LN, 5339LN, 4728LN, 4729LN
or 4739LN Functions Only
Adjust for Door Thickness
An ASSA ABLOY Group brand
80-9150-0060-010 (11-16)

5300LN or 4700LN
Cylindrical Lever Lockset
F old on Edge of Door
at proper Ba c kset Line
Place Dotted F old Line
on L o w Edge of Door
Place Solid F old Line
on High Edge of Door
B e veled Ed g e
Door On l y
Use this end o
f T emplate
f
or B e v eled Edge Doors
Ma r k Center of
Door thi c kness f or
7/8" or 1" Dia . Hol e .
5/16" Dia.
(8mm)
Th r u Door
2 Holes
2-1/8" Dia.
(54mm)
Th r u Door
5/32" x 1/8"
(4mm x 3mm)
Deep 2 place s .
Both sides of
doo r .
F old on Edge of Door
at proper Ba c kset Line
Square Ed g e
Door On l y
Ma r k Center of
Door thi c kness f or
7/8" or 1" Dia . Hol e .
T E
S
K
C
A B
2-3/8"
(60)
B A
CKSET
2-3/8"
(60)
2-3/4"
(70) T E
S
K
C
A B
2-3/4"
(70) T E
S
K
C
A B
Use this end o f T emplate
f or Square Edge Doors
2-3/4" (69.9)
Between Centers
CAUTION: IF PRINTED FROM WEBSITE, PRINT 1:1 SCALE.
TO CHECK, MEASURE SCALE ACROSS.
1"2"3"
5"
4"
3"
2"
1"
4
Product Support Tel [phone] • www.yalelocks.com
Copyright © 2002, 2016, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
An ASSA ABLOY Group brand
80-9150-0060-010 (11-16)