Yale Assure Lock SL YRD256 Technical specifications

Yea/ Living·
•
1
E? 3
4 5 s
7 B 9
✓
0 0
a 8
Before yo1J be9m
II
DOWNLOAD
THEBILTAPP
fur 30 imeractive
instructions& lo register
yourproduct
-- --- --~---------------------~
.,
m
Bllloa.-
Yale• Assure Lock- SL
Key Free Touchscreen Deadbolt
Installation and Programming Instructions
(YRD256/YRD456)
x2
M6x36mm
PPHMS
(2-1 /4")
@
'
x3
#8-32 X5/ 16 "
Optional
Network Module
.□.
~
oc:::::P
... ~.,,
•
x4
#7 wood & #8-32
machine x 20mm
Machine screws Combination screws
G x2
M6x44mm
PPHMS
(1-3 / 4-2 ")
G x2
M6x55mm
PPHMS
(1 -3/8")
FAILURETO FOLLOWTHESE INSTRUCTIONS COULD RESULT IN DAMAGE TO
THE PRODUCT AND VOID THE FACTORYWARRANTY
An ASSA ABLOY Group brand P/N YRL-SLKFTSINSTL-FUL Rev A
PSSA.ABIDf

□
Preparing to Install
Tools Needed
Standard
Phillips Head
Screwdriver
"'- ------
Tools necessary only
for new doors or
adjusting existing
prep.
•
Template
Drill
~
Utility Knife
Pencil Measure
Wood Mortise~
Chisel Level
.[ ~] 2-3/8" through bolt posts
default
l""""'*Backset
-
0
optional
PULL
!
2-3/4" through bolt posts
Note: Adjustment based on backset
~
* 2-3 /8" (60mm) or 2-3 / 4" (70mm)

Installing Latch & Strike Plate
x4
0
I ;::::::3 I
I I I
----
2-3/4
11
position
11111
Press
Bolt must be in retracted
~ (unlocked) position. Note
~ horizontal orientation of
mechanism.
t,
\ '
\ ',
\ ',
\
~,
---'-\
□ ----
.-Ii) ~
0
Pull.
0
0
[~]
0

Installing Touchscreen Escutcheon
Inside of Door
, ....
I ..
..
I ..
Bolt must be in retracted
(unlocked) position. Note
horizontal orientation of
mechanism.
Outside of Door
..
.. ..
..
..
..
.. @
..

x2
Installing Interior Mounting Plate
Loosen screw to
remove cover .
....
....
....
....
....
~
Choose
through bolt
appropriate for
your door
thickness.

Attaching the Cable Assembly

Installing Interior Escutcheon
T
x3
'

@
[✓] Testing Operation
•
'
-----
~
,,
, , t
,Q , , '
~, t
, t
t
t
Ll
Bolt must be in retracted
(unlocked) position before
installing batteries.
'''
' 0
''''
--- _, -~

Installing Batteries/Handing the Lock
11
Welcome to
Yale RealLiving.
11
Lock automatically adjusts for proper handing.
Installing Optional Network Module
............ -
~~~ ~ :::::::
Lt
Batteries must be removed
prior to removing and/or
inserting network module.

Installing Cover
Tighten screw
to replace cover .
Congratulations , you ' ve i nstalled the Yale ® Assure Lock ™ SL
Key Free Touchscreen Deadbolt (YRD256MRD456) !
Turn sheet over to Programming Instructions
to customize your product.

Programming Instructions
Exterior Escutcheon
•
1 2
4 5
7 B
✓
0
Indicator
"P" Key
(Return to Previous)
3
s
s
0
Speaker
Lockout
Mode
Failsafe 9 volt
Battery Connection
(Use Alkaline battery)
Interior Escutcheon
~
-
Privacy
Mode
Button
Lock Activation
Master PIN Code must be created before any further programming.
Max User Codes = 250 with Network Module . Max User Codes = 25 without.

Creating Master PIN Code
Creating a Master PIN Code must be performed upon installation orafter
resetting the lockto factory default Programming and use of lock is not
possible until this step has been successfully completed.
Enter4-8
digit Master
PIN Code.
1 2 3
4 5 6
7 B 9
1 2 3
4 5 6
7 B 9
" a
11
Register Master
Code. Press the gear
key to continue.
11
Press@
"Enter a 4 to 8 digit
PIN code followed by
the gear key.
11
"Registered.
11
Press@

Press@
Press@
Creating User PIN Codes
Master PIN code must be created first.
*Max user codes = 250 with Network Module . Max user codes = 25 without .
Press GJ
Press@
Adding more User Codes:
Press@
Enter 4-8 digit PIN code
Press@
1 2 3
4 5 S
7 B 9
Enter Master
PIN code
Press@
"Menu Mode,
enter number,
press the gear key
to continue.
11
1 2 3
4 5 S
7 B 9
✓ a o
Enter 4-8 digit PIN code
Press@
(code flashes)
4 5 S
7 B 9
✓ a
Cl 8
To end programming:
Press0
4 5 6
7 B 9

Unlocking Door with PIN Code
Code Chart Duplicate if necessary
Enter PIN Code
Press 0
1 2 3
4 5 6
7 B 9
" a o
PIN Code Management (With Network Module - Up to 250 Users)
User Type
User Name
User# PIN Code
Master
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-
User
-

Resetting Lock to Factory Default
When lock is reset to factory defaults all user
codes (including the Master PIN code*) are
deleted and all programming features are reset
to original default settings (see below).
1. Remove the battery cover and batteries.
2. Remove the interior escutcheon to access
the reset button.
3. The reset button (see image at right) is
located beside the PCB cable connector.
4. While pressing the reset button (minimum of
3 seconds) reinstall batteries. Release reset
button.
5. Replace battery cover.
Upon reset, MasterPIN Code creation is the
only option available and must be performed
prior to any other programming of the lock.
Factory Settings
Settings
Master PIN Code
Automatic Re-lock
Inside Indicator Light
One Touch Locking
Privacy Button Setting
Volume Setting
Language Setting
Lockout Mode
Automatic Re - lock Time
Wrong Code Entry Lim it
Shutdown Time
Interior Escutcheon
Factory Setting
Registration required*
Disabled
Disabled (Off)
Enabled
Disabled
Enabled (Low)
English
Disabled
30 Seconds
5 Times
60 Seconds
~he Master PIN code must be registered prior to any other programming of the lock.

Definitions
All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it
restricts all user (except Master) PIN code access. When attempting to enter a code while the
unit is in Lockout, the RED locked padlock will appear on the screen.
Automatic Re-lock Time: After a successful code entry and the unit unlocks, it will
automatically re-lock after thirty (30) seconds.
Inside Indicator Light: Located on the interior escutcheon. Shows active status (Locked) of
lock and can be enabled or disabled in the Advanced Lock Settings (Main Menu selection #3).
Language Setting Mode: Choosing English (1 ), Spanish (2) or French (3) becomes the
(default) setting for the lock's voice prompts.
Low Battery: When battery power is low, the Low Battery Warning indicator flashes RED.
If battery power is completely lost, use the 9Volt battery override. To use the 9V battery
override apply 9V battery, in either direction, to terminals below the touchscreen for backup
power option. Wake up the lock and enter your pin code to unlock the door .
Master PIN Code: The Master PIN code is used for programming and for feature settings.
It must be created prior to programming the lock. The Master code will also operate
(unlock/lock) the lock.
Network Module Setting: With the optional Network Module installed, this setting becomes
available thru the Main Menu (7) and allows the lock to connect with a network controller.
One Touch Locking: When the latch is retracted, activating the keypad will extend the latch
(during Automatic Re-lock duration or when Automatic Re-lock is disabled). When One-Touch
Re-lock is not in use (disabled), any valid PIN code will re-lock the lock .
Previous: While in Menu Mode, pressing this icon cancels the current operation and returns
the user to the previous step.
Privacy Mode: Privacy mode is disabled by default. Enable Privacy mode by pressing the
privacy button for 4 seconds to put the lock in do-not-disturb mode (all pin codes are
disabled).
Shutdown Time: The unit will shutdown (flashing RED) for sixty (60) seconds and not allow
operation after the wrong code entry limit (5 attempts) has been met.
Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door .
User PIN Code: The User code operates the lock. Maximum number of user codes is 250 with
Network Module; without Network Module, maximum is 25 user codes. Note: When deleting
User PIN code(s), screen will display User Number (not PIN code) being deleted.
Volume Setting Mode: The volume setting for PIN code verification is set to Low (2) by
default; otherwise it can be set to High (1) or SIient (3) for quiet areas.
Wrong Code Entry Limit: After five (5) unsuccessful attempts at entering a valid PIN code,
the unit will shut down and not allow operation.

Feature Programming Through Menu Mode
Using Master PIN code*
1. Touch screen with back of hand or palm to activate.~
2. Enter 4-8 digit master PIN code* followed by @ key.
Lock Response: "Menu mode, enter number, press @key to continue."
3. Enter digitcorresponding to the function to be performed followed by the@ key.
Followthe voice commands.
*The Master PIN code must be registered priorto any other programming
of the lock.
CDm+® Mam+®
"
Mam
the lock
Join 1he Network •
Exit the Network •
Preforms automatic
handing of the lock
Default settings
in bold.
*"This function appears only with
network module installed.
"'**This function appears only with
Bluetooth version installed.

Programming Troubleshooting
Symptom Suggested Action
• Touchscreen becomes active when pressed w/whole hand .
Lock does not respond -
Use a larger area of the hand or fingers and verify contact
door is open and
with at least 3 areas.
accessible.
• If touchscreen numbers are visible , check to see if they
respond when pressed .
• Check batteries are installed and oriented correctly (polarity)
in the battery case .
• Check batteries are in good condition; replace batteries*
if discharged .
• Check to see if touchscreen harness is fully connected
and not pinched.
Lock does not respond -•
Batteries may be completely discharged .
door is locked and
inaccessible . •
Apply 9V battery to terminals below the touchscreen for
backup power option.
Unit is on for a while then
shows no reaction . Lights
• Batteries do not have enough power . Replace batteries *.
dim .
Unit chimes to indicate • Check the door gaps for any foreign objects between door
code acceptance, but the
and frame .
door will not open.
• Check that the wire harness is firmly connected to the PCB .
Unit operates to allow
• Check to see if Auto Re-lock Mode is enabled .
access, but will not
• Disable Auto Re-lock Mode to lock the door (automatically) .
automatically re-lock . •
If low battery indicator is lit (see below), change batteries*.
• PIN codes must consist of 4 to 8 digits to register .
PIN codes will not register.
• The same PIN code cannot be used for multiple users.
• Registration/management of PIN codes is set by the
authority of the Master Code, which is set first.
• Contact the Master user .
• User codes must be entered within 5 seconds (while
touchscreen is active) or process will have to be restarted.
• Check 0 or gear @ cannot be used as part of the PIN code .
Upon entering a PIN code
• Lockout Mode is enabled.
and pressing 0 key, the
unit displays " invalid code " •
Only the Master can enable/disable Lockout Mode.
error or lock times out with-
• Contact the Master user.
out responding .
Upon entering a ~ code
• Check to see if the lock is set to Lockout Mode .
and pressing the ✓ key , •
Setting/managing Lockout Mode is done through
the red padlock icon appears
and there are different tones .
Master Code only . Contact the Master user .
The unit operates , but it
makes no sound . •
Check to see if Silent Mode is enabled (see Feature #4).
The unit responds • This is the alert to replace the batteries. Replace all four
" Low Battery "
(4) batteries* with new AA Alkaline batteries.
Upon entering a PIN code
and pressing the 0 key , •
The digits entered were incorrect or incomplete . Re - enter
the unit responds · wrong
the correct code followed by the check 0 key .
number of digits ·.
* When batter i es are replaced, Network Module locks have a real time clock that will be set
through the User Interface (UI) ;it is recommended to verify correct date and time
particularly those locks operating under Daylight Saving Time (DST) .
** Network Module locks only

Hardware Troubleshooting
Cycle lock in both the locked and unlocked positions. If problems are found:
Door is binding
a. Check that door and frame are properly aligned and door is free swinging.
b. Check hinges: They should not be loose or have excessive wear on knuckles.
Bolt will not deadlock
a. Check for sufficient clearance of the bolt within the strike-side jamb. Correct this by
increasing the depth of the pocket for the bolt.
b. Check for misalignment of bolt and/or strike which may be preventing bolt from
properly entering the strike. With the door open, extend and retract the bolt; if it is
smooth, check the strike alignment.
Bolt does not extend or retract smoothly
a. Bolt and strike are misaligned, see above.
b. Check the backset of door relative to adjustments already made to bolt.
c. Verify proper door preparation and re-bore holes that are too small or misaligned.
d. Verify keypad wire harness is routed under the bolt (see Fig. A).
e. Verify bolt is installed with correct side up (Fig. A).
Figure A
Keypad numerics are scrolling
Remove interior escutcheon and check to ensure that the wire harness lies flat against
the back recessed area and is properly routed along the side of the escutcheon and
tucked under the plastic cable guide.
NOTE TO INSTALLER AND CONSUMER
While Yale® has included several features to prevent lockout
(9-Volt battery jumper, low battery warnings), it is still possible
for a lockout situation to occur. Because this product does not
have a mechanical override (a key), Yale® recommends to use
this product in an environment where there are additional
entry points into the dwelling.

FCC:
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful Interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radionv technician for help.
Warning: Changes or modifications to this device, not expressly approved by Yale Security
Inc. could void the user's authority to operate the equipment.
Industry Canada:
This Class A digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations.
Cet appareillage numerique de la classe A repond a toutes les exigences de !'interference
canadienne causant des reglements d'equipement.
Yale Locks & Hardware
Product SupportTel 800.810.WIRE (9473) • www.yalelocks.com
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
Yale• andYale Real Living- are registered trademarks of Yale Security Inc., an ASSA ABLOY
Group Company. Assure Lock- is a trademark of Yale Security Inc., an ASSA ABLOY Group
Company. Other products' brand names may be trademarks or registered trademarks of their
respective owners and are mentioned for reference purposes only.© Copyright 2017.Yale
Security Inc., an ASSA ABLOY Group Company. All rights reserved. Reproduction in whole
or in part without the express written permission of Yale Security Inc. is prohibited.
YALE, with its unique global reach and range of products, is the world's favorite lock
-the preferred solution for securing your home, family and personal belongings.
ASSA ABLOY is theglobal leader in dooropeningsolutions,
dedicated to satisfying end-user needs for security, safety and convenience.