Yale SR-310 User manual

An ASSA ABLOY Group brand
Conexis L1
The smarter way to
protect your home
•
Yale Smart Home
Alarm Manual•
SR-310 • SR-320 • SR-330 • SR-340

smart
Living
Control your home
security from your
smartphone
2
The smarter way to
protect your home
•

3
Introduction
For more information on this product and
Yale Smart Living Range visit
www.yale.co.uk/smart-living
Consumer Support:
www.yale.co.uk/help
2
The 2 year guarantee for this
product is active from the
date of purchase (A copy of
this guarantee is available on
our website).
1. Location planning 4
2. Un-pack & power devices 6
3. Initial set-up 11
4. Mounting devices 13
5. Using the system 18
6. Default settings 21
7. Adding & Using devices 22
8. Changing batteries 26
9. Troubleshooting 31
10. Specications 33
Contents

4
Location Planning•
Plan device locations check devices range before mounting.
Operating 30m Range
Key Pad
• The Key Pad should be
accessible from a protected
entry/exit point
• Ensure that the Key Pad is
not visible from the outside of
the premises.
Panic Button
The Panic Button can activate your alarm
immediately - even when the system is
disarmed.
• Keep out of reach of children
• Keep hidden from view, but easily accessible.
Information and illustrations are subject to change within this
document. Yale reserves the right to alter the specication and
product design at anytime without notice. Yale® is a registered
trademark. © 2017 ASSA ABLOY. All rights reserved.
1
a
a
d
b
b
c
2
3
4
5 6
(12)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Ø 3.5mm
Ø 5mm
7
All devices must be within 30 metres of the Smart Hub and
must not be mounted on or near large metal objects. Avoid
obvious sources of electrical interference such as fridges and
microwave ovens.

5
PIR Motion Detector
• Mount 1.8m - 2.1m above oor level
• Location in a corner will ensure wider room coverage
• Do not mount the PIR where its eld of view will be
obstructed
• Do not point directly at sources of heat e.g. res or
boilers, and do not position directly above radiators
• Avoid mounting the PIR directly facing a window
• Do not point the PIR at a door protected by a Door/
Window Contact
Smoke Detector External Siren
Mount as high as possible, out of
easy reach.
Door/Window Contact
• Mount as high as possible on
the door or window frame.
Key Fob
• Use inside or outside within a
30m range
Smart Hub 2.0
• Ensure the Smart Hub is hidden
from view.
• Access to a mains socket and
broadband internet router is
required.
Introduction
(02)
Thank you for choosing the Yale Smart Home Alarm kit. This simple to install system has
been designed with the user in mind.
All the components are self contained and no connections are needed between the
units. There is no need to damage the home decor, lift carpets or run cables.
You can install up to 20 devices (Max. 6 PIR Cameras) in this system. As well as extra
door/window contacts, PIRs and smoke detectors, you can add keyfob remote controls
and keypads for added control convenience.
There is no need to wire into the mains supply or seek the services of a qualied
electrician. The Smart HUB is powered by an adaptor and all other components are
powered by battery (all batteries included). Batteries will operate for 2 years or more
before they need changing. Regular testing and battery changes (when notied by the
system) will ensure reliability and peace of mind.
The security detectors and external siren are ‘tamper’ protected. Any unauthorised
tampering with these items when the system is armed will result in an alarm.
Display extreme caution when using ladders or steps, please follow manufacturer’s
instructions. Be careful when using hand and power tools and follow the manufacturer’s
guidelines when using them. Take care that the correct tools are used. Wear goggles or
protective clothing where required. The external Siren is extremely loud, please ensure
you replace the cover and retreat to a safe distance before testing.
The dialling facilities must only be used with persons who have consented to being
contacted by the system. The system is not to be used to make 999 emergency calls
directly. Yale do not hold responsibility for any actions taken by emergency services for
incorrect use of the dialling facility.
Special Notes on Compatibility: This alarm system is NOT compatible with HSA6000
series and HSA3000 series accessories. Please note the prex “EF- & SR-” on the front of
the part number to indicate compatibility.
(03)
Learn
Power
LAN
Battery
<OnOff>
1
2
3
4
5
6
7
Learn
Power
LAN
Battery
<On Off>
(p. 04-06)
(p. 07)
(p. 08)
(p. 09-10)
(p. 22-24)(p. 11)
(p. 11)
(p. 12-21)
(GB) Step by step index -
Accessories vary depending on kit
Introduction
(02)
Thank you for choosing the Yale Smart Home Alarm kit. This simple to install system has
been designed with the user in mind.
All the components are self contained and no connections are needed between the
units. There is no need to damage the home decor, lift carpets or run cables.
You can install up to 20 devices (Max. 6 PIR Cameras) in this system. As well as extra
door/window contacts, PIRs and smoke detectors, you can add keyfob remote controls
and keypads for added control convenience.
There is no need to wire into the mains supply or seek the services of a qualied
electrician. The Smart HUB is powered by an adaptor and all other components are
powered by battery (all batteries included). Batteries will operate for 2 years or more
before they need changing. Regular testing and battery changes (when notied by the
system) will ensure reliability and peace of mind.
The security detectors and external siren are ‘tamper’ protected. Any unauthorised
tampering with these items when the system is armed will result in an alarm.
Display extreme caution when using ladders or steps, please follow manufacturer’s
instructions. Be careful when using hand and power tools and follow the manufacturer’s
guidelines when using them. Take care that the correct tools are used. Wear goggles or
protective clothing where required. The external Siren is extremely loud, please ensure
you replace the cover and retreat to a safe distance before testing.
The dialling facilities must only be used with persons who have consented to being
contacted by the system. The system is not to be used to make 999 emergency calls
directly. Yale do not hold responsibility for any actions taken by emergency services for
incorrect use of the dialling facility.
Special Notes on Compatibility: This alarm system is NOT compatible with HSA6000
series and HSA3000 series accessories. Please note the prex “EF- & SR-” on the front of
the part number to indicate compatibility.
(03)
Learn
Power
LAN
Battery
<On Off>
1
2
3
4
5
6
7
Learn
Power
LAN
Battery
<On Off>
(p. 04-06)
(p. 07)
(p. 08)
(p. 09-10)
(p. 22-24)(p. 11)
(p. 11)
(p. 12-21)
(GB) Step by step index -
Accessories vary depending on kit
Introduction
(02)
Thank you for choosing the Yale Smart Home Alarm kit. This simple to install system has
been designed with the user in mind.
All the components are self contained and no connections are needed between the
units. There is no need to damage the home decor, lift carpets or run cables.
You can install up to 20 devices (Max. 6 PIR Cameras) in this system. As well as extra
door/window contacts, PIRs and smoke detectors, you can add keyfob remote controls
and keypads for added control convenience.
There is no need to wire into the mains supply or seek the services of a qualied
electrician. The Smart HUB is powered by an adaptor and all other components are
powered by battery (all batteries included). Batteries will operate for 2 years or more
before they need changing. Regular testing and battery changes (when notied by the
system) will ensure reliability and peace of mind.
The security detectors and external siren are ‘tamper’ protected. Any unauthorised
tampering with these items when the system is armed will result in an alarm.
Display extreme caution when using ladders or steps, please follow manufacturer’s
instructions. Be careful when using hand and power tools and follow the manufacturer’s
guidelines when using them. Take care that the correct tools are used. Wear goggles or
protective clothing where required. The external Siren is extremely loud, please ensure
you replace the cover and retreat to a safe distance before testing.
The dialling facilities must only be used with persons who have consented to being
contacted by the system. The system is not to be used to make 999 emergency calls
directly. Yale do not hold responsibility for any actions taken by emergency services for
incorrect use of the dialling facility.
Special Notes on Compatibility: This alarm system is NOT compatible with HSA6000
series and HSA3000 series accessories. Please note the prex “EF- & SR-” on the front of
the part number to indicate compatibility.
(03)
Learn
Power
LAN
Battery
<OnOff>
1
2
3
4
5
6
7
Learn
Power
LAN
Battery
<On Off>
(p. 04-06)
(p. 07)
(p. 08)
(p. 09-10)
(p. 22-24)(p. 11)
(p. 11)
(p. 12-21)
(GB) Step by step index -
Accessories vary depending on kit
Introduction
(02)
Thank you for choosing the Yale Smart Home Alarm kit. This simple to install system has
been designed with the user in mind.
All the components are self contained and no connections are needed between the
units. There is no need to damage the home decor, lift carpets or run cables.
You can install up to 20 devices (Max. 6 PIR Cameras) in this system. As well as extra
door/window contacts, PIRs and smoke detectors, you can add keyfob remote controls
and keypads for added control convenience.
There is no need to wire into the mains supply or seek the services of a qualied
electrician. The Smart HUB is powered by an adaptor and all other components are
powered by battery (all batteries included). Batteries will operate for 2 years or more
before they need changing. Regular testing and battery changes (when notied by the
system) will ensure reliability and peace of mind.
The security detectors and external siren are ‘tamper’ protected. Any unauthorised
tampering with these items when the system is armed will result in an alarm.
Display extreme caution when using ladders or steps, please follow manufacturer’s
instructions. Be careful when using hand and power tools and follow the manufacturer’s
guidelines when using them. Take care that the correct tools are used. Wear goggles or
protective clothing where required. The external Siren is extremely loud, please ensure
you replace the cover and retreat to a safe distance before testing.
The dialling facilities must only be used with persons who have consented to being
contacted by the system. The system is not to be used to make 999 emergency calls
directly. Yale do not hold responsibility for any actions taken by emergency services for
incorrect use of the dialling facility.
Special Notes on Compatibility: This alarm system is NOT compatible with HSA6000
series and HSA3000 series accessories. Please note the prex “EF- & SR-” on the front of
the part number to indicate compatibility.
(03)
Learn
Power
LAN
Battery
<OnO ff>
1
2
3
4
5
6
7
Learn
Power
LAN
Battery
<On Off>
(p. 04-06)
(p. 07)
(p. 08)
(p. 09-10)
(p. 22-24)(p. 11)
(p. 11)
(p. 12-21)
(GB) Step by step index -
Accessories vary depending on kit
Introduction
(02)
Thank you for choosing the Yale Smart Home Alarm kit. This simple to install system has
been designed with the user in mind.
All the components are self contained and no connections are needed between the
units. There is no need to damage the home decor, lift carpets or run cables.
You can install up to 20 devices (Max. 6 PIR Cameras) in this system. As well as extra
door/window contacts, PIRs and smoke detectors, you can add keyfob remote controls
and keypads for added control convenience.
There is no need to wire into the mains supply or seek the services of a qualied
electrician. The Smart HUB is powered by an adaptor and all other components are
powered by battery (all batteries included). Batteries will operate for 2 years or more
before they need changing. Regular testing and battery changes (when notied by the
system) will ensure reliability and peace of mind.
The security detectors and external siren are ‘tamper’ protected. Any unauthorised
tampering with these items when the system is armed will result in an alarm.
Display extreme caution when using ladders or steps, please follow manufacturer’s
instructions. Be careful when using hand and power tools and follow the manufacturer’s
guidelines when using them. Take care that the correct tools are used. Wear goggles or
protective clothing where required. The external Siren is extremely loud, please ensure
you replace the cover and retreat to a safe distance before testing.
The dialling facilities must only be used with persons who have consented to being
contacted by the system. The system is not to be used to make 999 emergency calls
directly. Yale do not hold responsibility for any actions taken by emergency services for
incorrect use of the dialling facility.
Special Notes on Compatibility: This alarm system is NOT compatible with HSA6000
series and HSA3000 series accessories. Please note the prex “EF- & SR-” on the front of
the part number to indicate compatibility.
(03)
Learn
Power
LAN
Battery
<OnO ff>
1
2
3
4
5
6
7
Learn
Power
LAN
Battery
<On Off>
(p. 04-06)
(p. 07)
(p. 08)
(p. 09-10)
(p. 22-24)(p. 11)
(p. 11)
(p. 12-21)
(GB) Step by step index -
Accessories vary depending on kit
Pet PIR Motion Detector
• Suitable for homes with pets up to 25kg
• For rooms where pets are active and may climb on
furniture, protect the area with a door/window
contact instead to prevent false alarms.
30M
30M
30M
30M
30M
Mount on a ceiling in main
access areas e.g. hallways, top
of stairs.

6
Unpacking the devices•
2
4
3
Router
NOT INCLUDED
Learn
Power
LAN
Battery
<On O>
Battery
<On O>
<On O>
Learn
Power
LAN
Battery
<On O>
a
b
Smart Hub 2.0
1. Plug in the power adaptor and connect the Smart Hub to your internet router using the cable provided.
HOME SERVER
Top Light:
Shows server
connection status
Middle Light:
Shows fault status
Bottom Light:
Shows arming status
Solid Red -
Fully Armed
Flashing Red -
Part Armed
White -
Armed
OK
Fault - See
trouble shooting
(page 22) or
check app
for notifications
Alarm Hub Status

7
ale
Y
123
6
5
4
789
0
Panic button A
Panic button B
Disarm
HomeArm
LED
Learn button=
Press 8 and 9 together
/
Away
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Remove battery strips
(1
Test your planned location of components (2
Test location for radio signal strength (4
Press button to test connection
(3
(11)
(1 (IT) Rimuovi la linguetta della batteria - (DE) Entfernen der Batteriefolie - (NO) Fjern plastbeskyttelsen på batteriet
(SE) Ta bort batterifliken - (DK) Fjern batteri-strimmel
(2 (IT) Verifica la posizione scelta per i dispositivi - (DE) Testen Sie den geplanten Standort -
(NO) Test plasseringen av komponenten - (SE) Testa tilltänkta placeringen av sensorerna -
(DK) Test komponent placering
(3 (IT) Premere il pulsante per verificare la connessione - (DE) Drücken Sie den Knopf um die Verbindung zu testen
(NO) Trykk på knappen for å teste forbindelse - (SE) Tryck på knappen för att testa kopplingen -
(DK) Tryk knap for test af forbindelse.
(4 (IT) Verifica la connessione nella posizione prescelta - (DE) Testen Sie den Ort für die Stärke des Signals -
(NO) Test plassering i forhold til stabilitet av de trådløse signalene - (SE) Testa radiosignalens styrka -
(DK) Test placering for god trådløs forbindelse
8 9
5
6
ale
Y
Status
LED
Learn/Test button Cover
screw
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Remove battery strips (1
Test your planned location of components (2
Test location for radio signal strength (4
Press button to test connection (3
(11)
(1 (IT) Rimuovi la linguetta della batteria - (DE) Entfernen der Batteriefolie - (NO) Fjern plastbeskyttelsen på batteriet
(SE) Ta bort batterifliken - (DK) Fjern batteri-strimmel
(2 (IT) Verifica la posizione scelta per i dispositivi - (DE) Testen Sie den geplanten Standort -
(NO) Test plasseringen av komponenten - (SE) Testa tilltänkta placeringen av sensorerna -
(DK) Test komponent placering
(3 (IT) Premere il pulsante per verificare la connessione - (DE) Drücken Sie den Knopf um die Verbindung zu testen
(NO) Trykk på knappen for å teste forbindelse - (SE) Tryck på knappen för att testa kopplingen -
(DK) Tryk knap for test af forbindelse.
(4 (IT) Verifica la connessione nella posizione prescelta - (DE) Testen Sie den Ort für die Stärke des Signals -
(NO) Test plassering i forhold til stabilitet av de trådløse signalene - (SE) Testa radiosignalens styrka -
(DK) Test placering for god trådløs forbindelse
8 9
5
6
See page 16 for Key pad installation.
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Remove battery strips
(1
Test your planned location of components (2
Test location for radio signal strength (4
Press button to test connection
(3
(11)
(1 (IT) Rimuovi la linguetta della batteria - (DE) Entfernen der Batteriefolie - (NO) Fjern plastbeskyttelsen på batteriet
(SE) Ta bort batterifliken - (DK) Fjern batteri-strimmel
(2 (IT) Verifica la posizione scelta per i dispositivi - (DE) Testen Sie den geplanten Standort -
(NO) Test plasseringen av komponenten - (SE) Testa tilltänkta placeringen av sensorerna -
(DK) Test komponent placering
(3 (IT) Premere il pulsante per verificare la connessione - (DE) Drücken Sie den Knopf um die Verbindung zu testen
(NO) Trykk på knappen for å teste forbindelse - (SE) Tryck på knappen för att testa kopplingen -
(DK) Tryk knap for test af forbindelse.
(4 (IT) Verifica la connessione nella posizione prescelta - (DE) Testen Sie den Ort für die Stärke des Signals -
(NO) Test plassering i forhold til stabilitet av de trådløse signalene - (SE) Testa radiosignalens styrka -
(DK) Test placering for god trådløs forbindelse
8 9
5
6
ale
Y
Learn/Test
button
LED
Gap no more
than 10mm
Magnet
Sensor
Keypad
PIR
Door Contact

8
Unpacking the devices•
External Siren
WARNING
The Siren is very loud! Take care not to activate
the Siren tamper switch unnecessarily.
Plug in to mains socket.
Power Switch
(21)
7
1
3
4 5
2
6
a
a
a
b
b
b
c
d
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Ø 5mm
(21)
7
1
3
4 5
2
6
a
a
a
b
b
b
c
d
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Ø 5mm
1. 2.
PIR Image Camera
PIR Video Camera
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Remove battery strips
(1
Test your planned location of components (2
Test location for radio signal strength (4
Press button to test connection
(3
(11)
(1 (IT) Rimuovi la linguetta della batteria - (DE) Entfernen der Batteriefolie - (NO) Fjern plastbeskyttelsen på batteriet
(SE) Ta bort batterifliken - (DK) Fjern batteri-strimmel
(2 (IT) Verifica la posizione scelta per i dispositivi - (DE) Testen Sie den geplanten Standort -
(NO) Test plasseringen av komponenten - (SE) Testa tilltänkta placeringen av sensorerna -
(DK) Test komponent placering
(3 (IT) Premere il pulsante per verificare la connessione - (DE) Drücken Sie den Knopf um die Verbindung zu testen
(NO) Trykk på knappen for å teste forbindelse - (SE) Tryck på knappen för att testa kopplingen -
(DK) Tryk knap for test af forbindelse.
(4 (IT) Verifica la connessione nella posizione prescelta - (DE) Testen Sie den Ort für die Stärke des Signals -
(NO) Test plassering i forhold til stabilitet av de trådløse signalene - (SE) Testa radiosignalens styrka -
(DK) Test placering for god trådløs forbindelse
8 9
5
6
Camera
Flash light
Learn/Test button
Learn: Hold for 10 seconds
Test: Hold for 1 second
Learn/Test button
Camera
Flash light
Learn: Hold for 10 seconds
Test: Hold for 1 second
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Remove battery strips
(1
Test your planned location of components (2
Test location for radio signal strength (4
Press button to test connection
(3
(11)
(1 (IT) Rimuovi la linguetta della batteria - (DE) Entfernen der Batteriefolie - (NO) Fjern plastbeskyttelsen på batteriet
(SE) Ta bort batterifliken - (DK) Fjern batteri-strimmel
(2 (IT) Verifica la posizione scelta per i dispositivi - (DE) Testen Sie den geplanten Standort -
(NO) Test plasseringen av komponenten - (SE) Testa tilltänkta placeringen av sensorerna -
(DK) Test komponent placering
(3 (IT) Premere il pulsante per verificare la connessione - (DE) Drücken Sie den Knopf um die Verbindung zu testen
(NO) Trykk på knappen for å teste forbindelse - (SE) Tryck på knappen för att testa kopplingen -
(DK) Tryk knap for test af forbindelse.
(4 (IT) Verifica la connessione nella posizione prescelta - (DE) Testen Sie den Ort für die Stärke des Signals -
(NO) Test plassering i forhold til stabilitet av de trådløse signalene - (SE) Testa radiosignalens styrka -
(DK) Test placering for god trådløs forbindelse
8 9
5
6
On/Off, Test &
Learn button
Learn: Hold for 10 seconds
Power On/Off: Press & release
Test: Press & release

9
SR-SD
SR-PB
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
(23)
3 x 1.5v AA
CR 2032
SR-KF
CR 2032
3 x 1.5v AA
SR-PVC
(Lithium)
1. 2. 3.
SR-SD
SR-PB
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
(23)
3 x 1.5v AA
CR 2032
SR-KF
CR 2032
3 x 1.5v AA
SR-PVC
(Lithium)
SR-SD
SR-PB
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
(23)
3 x 1.5v AA
CR 2032
SR-KF
CR 2032
3 x 1.5v AA
SR-PVC
(Lithium)
Key Fob
Smoke Detector
Panic Button

10
Download the app•
First time registration
Follow the set-up instructions in the app.
E-mail used to set up system:
Smart Security Hub 2.0 serial number
Phone number used for notications:
Keypad PIN Code for Disarm/Arm (default 1234):
Keypad code for keypad setting (default 0000):
Recording your set-up information
Please ensure all devices are powered and operational at this point.
Download the Yale Home App
Internet Connection: Required on
iOS 9 + Android 4.2 +
(08)
(GB) App download - (IT) Scarica l'App -
(DE) App Download - (NO) Nedlasting av App - (SE) Installera appen -
(DK) Installer APP.
Yale Smart Living Home
3
IOS 9.0 +
Android 4.2 +
Serial No.
(08)
(GB) App download - (IT) Scarica l'App -
(DE) App Download - (NO) Nedlasting av App - (SE) Installera appen -
(DK) Installer APP.
Yale Smart Living Home
3
IOS 9.0 +
Android 4.2 +
Serial No.
Please register the hub within one hour of power up, otherwise app ‘authentication error’ will appear
– re-boot the hub (including switching o / on the back-up battery) and start the process again if
necessary.
Please Note:
Panel Serial Number can be
found on the Smart Hub sticker.
Serial No.

11
Setting up devices•
Adding new devices (Optional: Use it only if you have extra devices outside the kit)
All devices in the kit are linked to the Smart Hub. If you want to add more devices, you can do this by using the “Add new device”
section in the Smart Living Home app.
Exit Learn Mode:
Press Stop learning mode on the app
3
Go to the app menu
Setting > Alarm Setting > Devices and then press Add New Device button
1
Enter Learn Mode
Learn/ Test
button
Press & hold
for 3 seconds
Learn/Test
button
One single
press.
For the following accessories, please hold the Learn button for 10 seconds, before releasing to enter Learn mode.
Learn/Test
button
One single
press.
Learn/Test button
One single press.
Hold for 3 seconds Hold for 3 seconds
Hold for 3 seconds
Learn/Test button
One single press.
Learn/Test
button
One single
press.
Learn/Test
button
Press 8 and 9
together
Learn/Test button
Learn/Test button
Learn/Test button
LED
Press the learn button on the device you leant to add then see diagrams below. The Smart Hub will beep (single or multiple
dependent on device) when a new device is registered. You will then see your new device in your device List within the home app.
2
If the accessory doesn’t learn in, remove the batteries for 5 seconds, then replace
and try relearning within 3 minutes.
EF-PETPIR
SR-PC SR-PVC SR-PS
Learn in Devices
Ensure you
initialise your
keypad before
you learn it in.
(See page 17)
SR-PVC must be learned in with the
tamper screw removed so that the tamper
is open. Sensor will not learn with tamper
closed.

12
Range Test•
Check Accessories Range
1.) Place each device in the location where you wish to mount them.
Before mounting each device. Please check the system with a simple range test.
Login to your Yale Home App. Select “Tests”, “Device List” then select “Walk Test”.
Hold the devices in the desired location and press the Test/Learn button on the accessories. (see page 9)
If the sensor signal reached the Smart Hub, it will show in the device list on your app.
When you are happy that all your devices can communicate with the Smart Hub, please proceed to mounting the
accessories.
Before you mount a device use the device settings in the Smart Living Home app to bypass the device and disable the
tamper alert. After the device is fully in place don’t forget to disable the bypass.
Smart Hub 2.0 Mounting
The Smart Hub can be free standing, either vertically or horizontally on a at surface with access to mains socket and
broadband internet router.
It is also suitable for wall mounting. Using the two holes on the mounting back plate, mark the position of the holes. Drill
two holes and x with the screws and plugs provided. Hook the Smart Hub onto the plate.
1
2
4
(09)
(GB) Setting up - (IT) Configurazione - (DE) Einstellung -
(NO) Tilkobling og montering av alarmsentralen - (SE) Driftsättning -
(DK) Opsætning.
3
ab
4
Router
NOT INCLUDED
Learn
Power
LAN
Battery
<On Off>
Battery
<On Off>
<On Off>
Learn
Power
LAN
Battery
<On Off>
OR
a
b
c
Ø5mm
Learn
Power
LAN
Battery
<On Off>
a
b

13
Mounting Devices•
1
a
a
d
b
b
c
2
3
4
5 6
Ø 3.5mm
Ø 5mm
1
a
d
b
c
~1.8m
2.1m
2
a
a
b
b
3
4
5 6
Ø 5mm
Ø 3.5mm
PIR Motion Detector
Key Pad

14
Mounting Devices•
Door/Window Contact
1. The sensor should be on the frame while the magnet should be on the door/window.
Clean the mounting surface with a suitable degreaser agent and mount using the adhesive pads
Please note that some surfaces may be unsuitable for mounting using the adhesive pads. Please use
screwmounting in these cases.
1
3
5
6 7
2
4
a
a
b
b
max 10mm
or
(14)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Ø 3.5mm
7
5
6 7
a
b
or
Testing
The gap between the magnet and sensor should
be no more than 10mm when closed. Test to see
whether the magnet is in range of the sensor: before
mounting hold the magnet and sensor in place and
then pull them apart. If the sensor LED lights up it
implies the two items are within range.

15
Mounting Devices•
1
ad
b
c
~1.8m
2.1m
Ø 3.5 mm
Ø 5 mm
2
a
a
b
c
b
3
4
5 6
a
b
PIR Camera

16
Mounting Devices•
Mounting the External Siren
The tamper spring is fully compressed when the siren is mounted. If there is a gap, pack with a
suitable spacing material.
(21)
7
1
3
4 5
2
6
a
a
a
b
b
b
c
d
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Ø 5mm
3. 4.
(21)
7
1
3
4 5
2
6
a
a
a
b
b
b
c
d
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Ø 5mm
1.
(21)
7
1
3
4 5
2
6
a
a
a
b
b
b
c
d
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Ø 5mm
2.
Powering up the siren will
automatically disable the siren
tamper for three hour period.

17
Mounting Devices•
1
1
1
2
3
(15)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Pair / Test button
Pair / Test button
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
Ø 5mm
7
1. 2.
3.
1
1
1
2
3
(15)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Pair / Test button
Pair / Test button
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
Ø 5mm
7
1
1
1
2
3
(15)
(GB) Installation - (IT) Installazione - (DE) Installation - (NO) Installasjon - (SE) Installation -
(DK) Installation.
Pair / Test button
Pair / Test button
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
(IT) Associazione/test - (DE) Verbinden/Testen -
(NO) Tilkobling/Test - (SE) Para/Testa - (DK) Tilslut/test
Ø 5mm
7
Panic Button
Smoke Detector

18
Using the System•
Changing your Key Pad PIN
The default Key Pad PIN is 1234. You can set up to 10 sets of 4 digit PIN numbers in the app:
Arming and Disarming your Alarm
Using the Yale Home App
Swipe down to
part arm
Swipe down to
fully arm
Swipe

19
Using the System•
Conguring Device Behaviour
In your device list, go in to the settings for each device and select the required setting.
Setting up Part Armed Mode
Part Armed mode is usually used to protect the ground oor when you are upstairs in bed.
Burglar
Home Omit
Entry
Home Access
Disarmed Part-Armed Armed
Key
Burglar
Home Omit
Entry
Home Access
Disarmed Part-Armed Armed
Sensor
Ignored
Burglar
Home Omit
Entry
Home Access
Disarmed Part-Armed Armed
Instant Siren
Burglar
Home Omit
Entry
Home Access
Disarmed Part-Armed Armed
Triggers
Countdown

20
Using the System•
Adding Alert Notications
You can add/delete email addresses that will be alerted when the alarm is triggered. You can choose to have
ALL events (or Burglar only) reported via email.
as your VIP (Apple iOS) or Priority (Android) email and assign a special ringtone to it.
You can also add SMS alerts to specified mobile numbers (burglar events only)
Other manuals for SR-310
2
This manual suits for next models
3
Table of contents
Other Yale Security System manuals

Yale
Yale HSA6200 User manual

Yale
Yale SAA8011 User manual

Yale
Yale HSA3000 User manual

Yale
Yale SAA8012 User manual

Yale
Yale HSA6200 User manual

Yale
Yale SV-4C-2DB4MX User manual

Yale
Yale Sync IA-310 User manual

Yale
Yale IA-210 User manual

Yale
Yale HSA 3500 User manual

Yale
Yale Smart Living SV-4C-2ABFX User manual

Yale
Yale HSA3400 User manual

Yale
Yale Distress alert system User manual

Yale
Yale SAA8012 User manual

Yale
Yale HSA3095 User manual

Yale
Yale Smart Living SV-4C-2ABFX User manual

Yale
Yale YL-SR-320 User manual

Yale
Yale SmartHome Alarm series User manual

Yale
Yale Y402A-HD User manual

Yale
Yale DAS1100 User manual

Yale
Yale HSA6092 User manual