Yale SmartHome Alarm series User manual

User/Master Manual
Table of contents
Operation Summary 2
Control panel keys overview 3
Entering the user manual 4
Disarming the system 5
iButton 5
Duress code 5
User Menu
Fault List 6
Hear Answer MC 6
Full Arm 7
Part Arm#1/2/3 8
Lone Occupant 8
-Forced Arming 9
-Arming with Door Opened 9
-Arming with Supervisory Fault 10
Set Time/Date 10
-Time 10
-Date 10
-Year 10
-Daylight 11
ByPass Sensor 11
RSPS/ILPS/ZE88 12
Event Log 12
Change Pincode 12
GSM 12
Master Setup 13
-User Setting 13
-Engineer Access 15
-Alarm Clock 15
-Panel Key LED 15
-Status LED 15
-Answer Machine 15
-Front Tamper 16
-Desk Tamper 16
PSTN and GSM/GPRS Functions
-Telephone function 17
-Remote Command 17
-Rec. Voice message 20
-Alarm reporting 20
SmartHome Alarm series

Arming Modes:
Full Arming:
Control panel- Enter pincode, press “0”
Keypad- Enter pincode, press Full Arm button
Keyfob- Press Full arm button.
Part Arming #1/2/3:
Control panel- Enter pincode, press “1”, “2” or “3”
Keypad- Enter pincode, press the associated Part Arm button
Keyfob- Press the associated part arm button.
Lone Occupant mode:
Control panel- When Alarm off, enter pincode, press “4”
Keypad- Enter pincode, press the associated Lone occup. button
Keyfob- Press the associated Lone occupant button.
Disarm:
Control panel- Enter pincode, press ok.
Keypad- Enter pincode, press the Disarm button
Keyfob- Press the Disarm button.
Other functions:
Change your pincode:
User menu-> Change pincode
Contact Engineer
Press & hold up key for 5 sec
Listen to answer machine:
User menu-> Hear Answer MC
View faults:
User menu-> Fault List
Operation Summary
2

Control Panel Keys Overview
1. Backlit LCD Screen
2. Up arrow Key
• Scroll up the selection list.
• Press once to enable the handfree
telephone function.
3. Down arrow Key
• Scroll down the selection list.
4. Blue LED
• ON: AC Power is ON.
• Off: AC Power is Off.
5. Red LED
• ON: Fault
• OFF: Normal
6. Yellow LED
• ON: module inserted
• OFF: no module inserted
7. iButton
• Press the iButton to playback voice
guidance.
8. Numeric Key 0 (Full Arm Key)
• Used as a numeric key
• Also used to Full Arm the system
9. Engineer/Programming Menu
Key
10. Numeric Key 4 (Lone Occupant
Key)
• Used as a numeric key
• The shortcut key used to enable the
Lone Occupant mode.
11. Numeric Key 1, 2 & 3 (Part Arm#
1, 2 & 3)
• Used as a numeric keys
• Shortcut for Part Arm# 1, 2 & 3
modes.
12. Speaker
13. OK/Enter/Yes Key
• Used to confirm the selection.
14. Return/No Key
• Used to delete entered numbers,
cancel the selection and select “No”.
15. Microphone
123
4 5 6
789
0
abcdef
ghijklmno
pqrs
tuv wxyz
M
1
2
3
4
5
6
7 8 9
12
13
14
15
10 11
23
22
19 18 17 16
20
21
29
24
28
25
26
27
Control panel Overview
3

Entering the User Menu
Under the “Alarm off” condition,
user can access the user menu via
entering a valid user code.
Press any key to wake up the
panel’s keypad, and proceed to
enter the user pincode. when the
first numberic key is pressed, the
display will show:
enter code
*.....
Enter the 4 or 6 digit pincodes
followed by OK within 30 seconds.
The options for the user menu
.Fault List
Hear answer mc
full arm
part arm #1
lone occupant
set time/date
bypass sensors
RSps/ilps/ZE88
event log
change pincode
gsm
master setup
Notes:
1) Fault List is only shown if there is
a fault event in the system
2) Selection shown will depends on
User attribute setting.
3) Part Arm 2 and 3 will be shown if
enabled.
4) RSPS/ILPS/ZE88 and GSM will
only be shown if the relevant device
exists in the system.
5) If a Master pincode was used, the
option Master Setup will be shown.
6) Hear Answer MC (Machine) is only
shown if there the Answer Machine
is enabled, and there is a message
in memory.
7) For system with 2 Areas defined,
a user with access to both areas
will need to first choose the area
specific user menu. Press 1 for Area
1 and 2 for Area 2.
a1:off, a2:off
1 for a1 menu
4

Disarming the system
Using the Control panel
Under the “Alarm on” condition
(system armed), the user can disarm
the system via entering a valid user
code.
Press any key to wake up the
panel’s keypad, and proceed to
enter the user pincode.
enter code
*.....
Press OK to disarm. The following
will then be shown:
alarm off
00:01 01 jan
* Date shown as example
Using the remote Keyfob (ENA-KF)
Press the Disarm button to disarm
the system. If your engineer
disabled the “KF entry option”,
when under full arm, you will need to
first enter the premises and trigger
and entry/delay sensor before you
can disarm the system.
Using the remote Keypad (ENA-KP)
Enter your pincode and press the
disarm button on the keypad to
disarm the system.
i button (voice assist)
Should the user require further
assistant during system operation,
press the i button to playback
supplementary information. Press
the i button for a second time during
playback to stop this function.
Duress code
Under a holdup situation, the user
maybe required to arm or disarm
the alarm system. In order to avoid
aggravating the situation, duress
code (can be used for arming and
disarming) is provided to silently
alert the third party. A duress event
will trigger the panel to report
Panic Alarm event (Contact ID 121)
should it be connected to an alarm
monitoring center.
The Duress Code is related to the
User pincode #1. The last digit will
increment by one. i.e. 1 =2, 2=3, 9=0
etc.
Example:
If the user pincode #1 is 123400,
the Duress Code is 12340”0”+1=
123401.
If you set the user pincode # 1 as
1234, the Duress Code is 123”4”+1=
1235.
Special Case for 9 as the last digit:
If you set the user pincode # 1 as
1349, the Duress Code is 134”9”+1
= 1340.
5

Fault List
The fault list allows you to see/
delete a list of fault events. A fault
event only appears if there is a fault
event happening in your system.
Upon selecting the option, you will
be shown:
start
v
Scroll down to see a list of faults. To
clear faults, press return key.
clear fault
display? (ok?)
Press ok to clear fault. If the fault
still persists on the system, the fault
will immediately reappear on the list.
Please contact your installer/
engineer to rectify the fault.
Hear Answer MC
Note: Only shown if the Answer
Machine option is enabled and the
control panel is connected to either
the GSM/GPRS or PSTN phone line.
When the caller leaves messages
on the system, this option will be
shown. Once selected, it will inform
you if there are more than one
recording (max. 20 voice messages).
there are 02
records
It will then proceed to playback
all the messages starting from the
oldest message. Message order and
the time/date info will be displayed.
play record 01
11:33 may 12
You can stop the playback by
pressing the Return key. The system
will ask you if you want to delete All
the voice messages.
do you erase
the records?
Press the OK key to confirm deleting
or press the Return key to go back
to the main menu without deleting.
User Menu
6

Full Arm
The Full Arm mode is intended
for fully arming the property when
there are no occupants. If Area 2 is
defined, the system may ask you to
choose one of the areas for arming
(if the user have access to both
areas). To full arm the system:
Keyfob- Press full arm
Keypad- Enter pincode follow by
pressing full arm.
Control panel- In Alarm off mode,
enter pincode and press ok. Select
Full arm and press ok; or press
“0” to full arm the system. On the
screen it will show:
time to exit
30 sec
When the entry delay time expires,
the control panel will emit a long
beep. The LCD will display an Alarm
On message and the system is now
in the full arm mode. If the Final
Door option is enabled, the system
will immediately arm when the door
contact (delay attribute) is closed,
i.e. user left the property.
Stop Entry Delay
During the entry countdown, the
user can prevent the system from
sounding and reporting by:
Keyfob- Press disarm
Keypad- Enter pincode follow by
pressing disarm.
Control panel- Enter pincode and
press OK.
Stop Exit Delay
During the exit countdown, user can
prevent the system from arming by:
Keyfob- Press disarm
Keypad- Enter pincode follow by
pressing disarm.
Control panel- Press return key.
Enter pincode and press OK.
Extend Exit Delay
During the exit countdown, user can
extend the Exit Delay by:
Keyfob- Press full arm
Keypad- Enter pincode follow by
pressing full arm.
*Each time this is done, the delay
time will start counting from the
beginning.
Disarm the system
When the full arm mode is set, you
can disarm the system by:
Keyfob- Press disarm
Keypad- Enter pincode follow by
pressing disarm.
Control panel- Enter pincode and
press OK.
7

Part Arm 1/2/3
The Part Arm Mode is used when
the user wish to secure part of the
premise while leaving the another
area free to roam. Part arm #2 and
#3 will only be shown if they were
enabled by installer/engineer.
If Area 2 is defined, the system may
ask you to choose one of the areas
for arming (if the user have access
to both areas). To part arm the
system:
Keyfob- Press Part arm
Keypad- Enter pincode follow by
pressing Part arm.
Control panel- In Alarm off mode,
enter pincode and press ok. Select
Part arm 1, 2 or 3 and press ok.
Alternatively press “1” for Part arm
#1, “2” for Part arm #2, “3” for Part
arm #3. On the screen it will show:
time to exit
30 sec
When the entry delay time expires,
the control panel will emit a long
beep. The LCD will display Part Arm
1/2/3 and the system is now in the
part arm mode.
Lone Occupant
The Lone Occupant mode allows
a user to deactivate (bypass) any
sensors so that it will not trigger the
Alarm for one-time only operation.
This feature is ideal when the
occupant plans to stay in one area
for a prolonged length of time, and
they wish to arm all other areas.
Step 1. Select Lone Occupant or
just press the shortcut key 4 on the
control panel (under the user menu
screen). They system will now enter
300 seconds count down.
lone occupant
300 sec
Step 2. Any sensor which is
triggered (either by motion or by
pressing the test/learn button)
during the countdown period will
be bypassed. The panel will sound
a warning beep every time a sensor
is triggered during this countdown
period.
8

Force Arming
Force Arming allows the user to
full arm or part arm (lone occupant
mode included) the system with a
Fault condition present.
Where possible, please rectify the
fault before arming. The system will
prevent you from arming normally
when a fault is present (except
device/panel low battery), and the
user will need to carry out another
step in order to force arm the area.
To force arm the system:
Arm the system normally via keyfob,
keypad or the control panel. The
Control Panel will emit a warning
sound to indicate faults and the
panel screen will scroll through all
the faults one by one.
For keypad and keyfob, arm the
system for a second time within 30
seconds of the first attempt. The
system is now forced arm.
For control panel, press OK and
the system will prompt you for your
pincode. Press ok and the following
display will be shown:
force arm
(OK?)
Press OK to confirm. The defined
timer starts to Count Down. Please
note for Lone occupant mode it will
be 300 seconds.
time to exit
30 sec
When the Exit Delay timer expires,
the Control Panel will emit a long
beep and the system is now in the
designated Arm Mode.
Arming with door opened
If the user tries to arm the system
while a door contact is opened,the
Control Panel will emit a warning
sound to indicate faults and the
panel screen will display the
following screens:
fault dsp
10:39 jan 29
door opened
DC Z01
If the door/window is shut
immediately, the fault on screen will
be cleared and the system will revert
to alarm off mode. The system can
now be armed normally.
Should you wish to arm the system
with the door contact being open,
follow the steps described in the
Force Arming section for operation.
9

Arming with Supervisory
fault
The Siren, PIR sensor, Door Contact,
and Smoke detector will transmit a
periodic Supervision signal to the
control panel.
If the user tries to arm the system
while the control panel failed to
receive a supervisory signal,the
Control Panel will emit a warning
sound to indicate faults
Should the user wish to arm
the system while ignoring the
supervisory fault, follow the steps
described in the Force Arming
section for operation.
Set Time/Date
This option allows you to set the
system time and date. You can also
define your local daylight saving
hour.
.time
date
year
daylight
Time
Use the Up and down key to define
the 24hr time. Press OK to confirm
the setting.
Date
Use the Up and down key to define
the Month and Day. Press OK to
confirm the setting.
Year
Use the Up and down key to define
the year. Press OK to confirm the
setting.
10