Yeastar Technology Elastix Safety guide

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 1/15
How to Connect Elastix to NeoGate
TA FXS Gateway
Version: 1.0
Yeastar Technology Co., Ltd.
Date: 2014.06.06

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 2/15
Table of Contents:
1. Introduction..................................................................................... 3
2. Preparation...................................................................................... 4
3. VoIP Mode....................................................................................... 5
4. SPS/SPX Mode ................................................................................. 8

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 3/15
1. Introduction
This application note shows how to connect Elastix to NeoGate TA FXS gateway.
This guide has been tested with NeoGate TA3200 and Elastix firmware version:
2.4.0.
Two modes are available for NeoGate TA to connect to Elastix, we call them VoIP
trunk mode and Service Provider SIP/IAX trunk mode (SPS/SPX).
*You can simply choose one mode to achieve the connection.
Target：
After connecting NeoGate TA3200 and Elastix, FXS extensions will be extended
on Elastix. Once the FXS ports are connected to Elastix, the phones connected
to the FXS ports will be treated as Elastix FXS extensions. The following features
can be achieved:
1. Make calls between the analog phone and Elastix SIP extension;
2. Receive incoming calls on the analog phones;
3. Make external calls from the analog phones using trunks on Elastix.
Description：
IP address of Elastix: 192.168.5.178
IP address of NeoGate TA3200: 192.168.5.13
Figure 1. Connect Elastix and NeoGate TA3200

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 4/15
2. Preparation
NeoGate TA3200 attempts to contact a DHCP server in your network to obtain
valid network settings (e.g., the IP address, subnet mask, default gateway
address and DNS address) by default.
Before connecting NeoGate TA3200 to Elastix, you need to set a static IP
address from the same LAN with the Elastix.
Steps to set static IP for NeoGate TA3200:
1. Connect one analog phone in one of the FXS ports on NeoGate TA3200;
2. Dial "***" to enter the voice menu;
3. Press "1" to check the IP address;
4. Open the browser and type in the TA3200's IP address to access TA3200;
5. Log in TA3200 and go to System→Network Preferences→LAN Settings,
disable DHCP and configure the LAN network, save and apply the changes,
reboot NeoGate TA3200 to take effect.
Figure 2. Configure LAN Settings on NeoGate TA3200

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 5/15
3. VoIP Mode
If you choose VoIP mode, the FXS ports will be registered as the Elastix's SIP
extensions, whose functions are the same with other SIP extensions on Elastix.
Figure 3. Connect TA3200 and Elastix via VoIP Mode
Step 1. Create a SIP extension on Elastix.
Path: PBX→Extensions→Add Extension
Create an extension on Elastix for the FXS port on the TA3200 which has
connected an analog phone. Here we take extension 9000 for example.
Figure 4. Create Extension 9000 on Elastix
Step 2. Configure one VoIP server template on NeoGate TA3200.

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 6/15
Path: Gateway→VoIP Settings→VoIP Server Settings
Check "Enable Register", fill in the Elastix IP address; this VoIP server template
will be a VoIP mode template.
Figure 5. Configure the VoIP Server Template as VoIP Mode
Server Name: Elastix
Type: SIP
Enable Register: checked
Transport: UDP
Hostname/IP: fill in the Elastix IP address, 192.168.5.178
Domain: fill in the Elastix IP address, 192.168.5.178
Step 3. Edit the Dial Pattern Template
Path: Gateway→VoIP Settings→VoIP Server Settings
The default dial pattern is set as ".", which allows you to dial any number out. In
this guide, we will remain the default setting. You can change it according to
your environment.

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 7/15
Figure 6. Edit Dial Pattern Template
Step 4. Edit the FXS port
Path: Gateway→FXS Port List→FXS Port List
Figure 7. Edit the FXS Port
Primary Server: choose “Elastix(3)”, the VoIP server template configured in
Step 2.
User Name: the extension username on Elastix, 9000.
Authentication Name: the extension authentication name on Elastix, 9000.
Password: the authentication password of the extension on Elastix,
pincode9000.
Dial Pattern Template: choose the Dial Pattern Template:

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 8/15
DialPatternTemplate1(1).
Save and apply the changes, and you will see the port status is “Registered” on
"Port Status" page.
Path: Status→System Status→Port Status
Figure 8. Port Status
Now, you are able to use the analog phone which is connected to NeoGate TA's
FXS port 1 to make calls and receive calls.
Note: ALL outgoing calls to Elastix extensions and to external numbers through
trunks on Elastix should match the dial pattern, or calls will fail.
4. SPS/SPX Mode
If you choose this mode to connect NeoGate TA3200 and Elastix, the FXS port
will be registered as a Service Provider SIP/IAX (SPS/SPX) trunk to the Elastix.
One SPS/SPX trunk to NeoGate TA also should be created on Elastix. In this
guide, we use SIP protocol, configure one VoIP server template as SPS mode on
NeoGate TA3200 and create one Service Provider SIP trunk on Elastix.
Figure 9. Connect TA3200 and Elastix via SPS Mode

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 9/15
Step 1. Create a Service Provider SIP Trunk on Elastix
Path: PBXTrunksAdd SIP Trunk
Figure 10. Add SIP Trunk

How to Connect Elastix to NeoGate TA FXS Gateway
http://www.yeastar.com 10/15
Figure 11. Configure SIP Trunk
PEER Details:
host=192.168.5.13
type=peer
qualify=yes
disallow=all
allow=ulaw,alaw,gsm
After creating the SIP trunk, we can check the status of this trunk, it should be
OK.
Path: PBXTools
Enter the command “sip show peers”and click “Execute”, the status will be
seen.