YOKOGAWA DLM3022 User manual

IM DLM3054-02EN
1st Edition
Mixed Signal Oscilloscope
DLM3024, DLM3034, DLM3054
Digital Oscilloscope
DLM3022, DLM3032, DLM3052
nbn Austria GmbH

i
IM DLM3054-02EN
Thank you for purchasing the DLM3022, DLM3032, or DLM3052 digital oscilloscope or the DLM3024,
DLM3034, or DLM3054 mixed signal oscilloscope. This User’s Manual explains how to use the
instrument. To ensure correct use, please read this manual thoroughly before operation.
After reading this manual, keep it in a safe place. The manuals for this instrument are listed on the next
page. Please read all manuals.
Contact information of Yokogawa offices worldwide is provided on the following sheet.
Document No. Description
PIM 113-01Z2 List of worldwide contacts
Notes
• The contents of this manual are subject to change without prior notice as a result of continuing
improvements to the instrument’s performance and functions. The figures given in this manual may
differ from those that actually appear on your screen.
• Every effort has been made in the preparation of this manual to ensure the accuracy of its
contents. However, should you have any questions or find any errors, please contact your nearest
YOKOGAWA dealer.
• Copying or reproducing all or any part of the contents of this manual without the permission of
YOKOGAWA is strictly prohibited.
• The TCP/IP software of this product and the documents concerning it have been developed/created
by YOKOGAWA based on the BSD Networking Software, Release 1 that has been licensed from
the Regents of the University of California.
Trademarks
• Microsoft, Internet Explorer, MS-DOS, Windows, Windows 7, Windows 8.1, and Windows 10 are
registered trademarks or trademarks of Microsoft Corporation in the United States and/or other
countries.
• Adobe and Acrobat are either registered trademarks or trademarks of Adobe Systems Incorporated.
• DLM is a registered trademark of Yokogawa Electric Corporation.
• In this manual, the TM and ® symbols do not accompany their respective registered trademark or
trademark names.
• Other company and product names are trademarks or registered trademarks of their respective
holders.
Revisions
• 1st Edition:November 2018
1st Edition: November 2018 (YMI)
All Rights Reserved, Copyright © 2018 Yokogawa Test & Measurement Corporation

ii IM DLM3054-02EN
Manuals
The following manuals, including this one, are provided as manuals for this instrument. Please read all
manuals.
Manual Title Manual No. Description
DLM3022, DLM3032, DLM3052
Digital Oscilloscope
DLM3024, DLM3034, DLM3054
Mixed Signal Oscilloscope
Features Guide
IM DLM3054-01EN The supplied CD contains the PDF file
of this manual. This manual explains all
the instrument’s features other than the
communication interface features.
DLM3022, DLM3032, DLM3052
Digital Oscilloscope
DLM3024, DLM3034, DLM3054
Mixed Signal Oscilloscope
User’s Manual
IM DLM3054-02EN This document. The supplied CD contains the
PDF file of this manual. The manual explains
how to operate this instrument.
DLM3022, DLM3032, DLM3052
Digital Oscilloscope
DLM3024, DLM3034, DLM3054
Mixed Signal Oscilloscope
Getting Started Guide
IM DLM3054-03EN Provided as a printed manual.
This guide explains the handling precautions,
common operations, troubleshooting
measures, and specifications of this
instrument.
DLM3022, DLM3032, DLM3052
Digital Oscilloscope
DLM3024, DLM3034, DLM3054
Mixed Signal Oscilloscope
Operation Guide
IM DLM3054-04EN Provided as a printed manual.
Explains the basic operations of this
instrument. Operations are described in steps
from “Preparation” to “Displaying Waveforms,”
“Measuring Waveforms,” and “Saving Screen
Captures.”
DLM3022, DLM3032, DLM3052
Digital Oscilloscope
DLM3024, DLM3034, DLM3054
Mixed Signal Oscilloscope
Communication Interface User’s Manual
IM DLM3054-17EN The supplied CD contains the PDF file of this
manual. Explains the functions of the this
instrument’s communication interface, how to
configure it, and how to control this instrument
from a PC using the interface.
DLM3022, DLM3032, DLM3052
Digital Oscilloscope
DLM3024, DLM3034, DLM3054
Mixed Signal Oscilloscope
IM DLM3054-92Z1 Document for China
The “EN” and “Z1” in the manual numbers are the language codes.
Manuals in the CD
The included CD (manual CD) contains the following English and Japanese manuals.
File Name Manual No. Description
Features Guide & Users Manual.pdf IM DLM3054-01EN
IM DLM3054-02EN
Features Guide and User’s Manual
Communication Interface.pdf IM DLM3054-17EN Communication Interface User’s Manual
Online Help
A help document in HTML format stored in the instrument. The contents of this document are the
same as the Features Guide (IM DLM3054-01EN). For the operating procedure, see section 3.10 in
the Getting Started Guide (IM DLM3054-03EN).

iii
IM DLM3054-02EN
DLM Models and Conventions Used in This Manual
Models Explained
This manual explains the 4-channel model of this instrument. Channel settings vary depending on the
model.
Notes
The notes and cautions in this manual are categorized using the following symbols.
Improper handling or use can lead to injury to the user or damage to the
instrument. This symbol appears on the instrument to indicate that the user must
refer to the user’s manual for special instructions. The same symbol appears
in the corresponding place in the user’s manual to identify those instructions.
In the manual, the symbol is used in conjunction with the word “WARNING” or
“CAUTION.”
WARNING Calls attention to actions or conditions that could cause serious or fatal injury to
the user, and precautions that can be taken to prevent such occurrences.
CAUTION Calls attention to actions or conditions that could cause light injury to the user or
damage to the instrument or user’s data, and precautions that can be taken to
prevent such occurrences.
French
AVERTISSEMENT Attire l’attention sur des gestes ou des conditions susceptibles
de provoquer des blessures graves (voire mortelles), et sur les
précautions de sécurité pouvant prévenir de tels accidents.
ATTENTION Attire l’attention sur des gestes ou des conditions susceptibles de
provoquer des blessures légères ou d’endommager l’instrument ou les
données de l’utilisateur, et sur les précautions de sécurité susceptibles
de prévenir de tels accidents.
Note Calls attention to information that is important for the proper operation of the
instrument.
Unit
k Denotes 1000. Example: 100 kS/s (sample rate)
K Denotes 1024. Example: 720 KB (file size)

iv IM DLM3054-02EN
Contentsの1.1のの16.1のののののののののののの のののののの
Contents
Manuals ............................................................................................................................................ii
DLM Models and Conventions Used in This Manual....................................................................... iii
Chapter 1 Vertical and Horizontal Control
1.1 Setting the Vertical Axis (Analog Signal) .......................................................................... 1-1
1.2 Setting the Vertical Axis (Logic Signal) (On models with the logic signal input port)........ 1-6
1.3 Setting the Horizontal Scale (Time Scale)...................................................................... 1-13
Chapter 2 Trigger
2.1 Setting the Trigger Mode and Trigger Hold-off Time......................................................... 2-1
2.2 Setting the Trigger Position and Trigger Delay................................................................. 2-2
Edge Trigger
2.3 Triggering on an Edge Trigger.......................................................................................... 2-4
Enhanced Trigger
2.4 Triggering on the OR of Multiple Edge Triggers ............................................................... 2-6
2.5 Triggering on Multiple Input Patterns................................................................................ 2-7
2.6 Triggering on Pulse Width ...............................................................................................2-11
2.7 Triggering on Rise and Fall Times.................................................................................. 2-13
2.8 Triggering on Runt Signals ............................................................................................. 2-15
2.9 Triggering on Timeout Period ......................................................................................... 2-17
2.10 Triggering on a Window Trigger ..................................................................................... 2-18
2.11 Triggering on the OR of Multiple Window Triggers......................................................... 2-20
2.12 Triggering on Edge Intervals .......................................................................................... 2-21
2.13 Triggering on FlexRay Bus Signals (Option) .................................................................. 2-23
2.14 Triggering on CAN Bus Signals (Option)........................................................................ 2-26
2.15 Triggering on CAN FD Bus Signals (Option) .................................................................. 2-31
2.16 Triggering on LIN Bus Signals (Option).......................................................................... 2-37
2.17 Triggering on CXPI Bus Signals (Option) ....................................................................... 2-41
2.18 Triggering on SENT Signals (Option) ............................................................................. 2-46
2.19 Triggering on UART Signals (Option)............................................................................. 2-53
2.20 Triggering on I2C Bus Signals (Option) .......................................................................... 2-57
2.21 Triggering on SPI Bus Signals (Option).......................................................................... 2-62
2.22 Triggering On User-Defined Serial Bus Signals ............................................................. 2-66
2.23 Triggering on a TV Trigger.............................................................................................. 2-69
B Trigger
2.24 Triggering on Combination Triggers (B TRIG)................................................................ 2-71
Forced Trigger
2.25 Forcing the Instrument to Trigger (FORCE TRIG).......................................................... 2-73
Action, GO/NO-GO
2.26 Setting the Action-On-Trigger Function .......................................................................... 2-74
2.27 Performing GO/NO-GO Determination........................................................................... 2-75

v
IM DLM3054-02EN
Contentsの1.1のの16.1のののののののののののの のののののの
Contents
Chapter 3 Waveform Acquisition
3.1 Setting Conditions for Waveform Acquisition.................................................................... 3-1
3.2 Acquiring Waveforms ....................................................................................................... 3-3
Chapter 4 Screen Display
4.1 Setting Display Conditions ............................................................................................... 4-1
4.2 Using the Accumulate Feature ......................................................................................... 4-3
4.3 Using the Snapshot and Clear Trace Features ................................................................ 4-4
4.4 Adjusting the Backlight ..................................................................................................... 4-5
Chapter 5 XY Display
5.1 Displaying XY Waveforms ................................................................................................ 5-1
5.2 Performing Cursor Measurements and Area Calculations ............................................... 5-2
Chapter 6 Computed and Reference Waveforms
6.1 Setting the Computation Mode......................................................................................... 6-1
6.2 Performing Addition, Subtraction, and Multiplication ........................................................ 6-2
6.3 Performing Filter Functions .............................................................................................. 6-3
6.4 Performing Integration...................................................................................................... 6-5
6.5 Performing Count Computations ...................................................................................... 6-6
6.6 Setting Labels, Units, and Scaling.................................................................................... 6-8
6.7 Loading Reference Waveforms ........................................................................................ 6-9
6.8 Performing User-Defined Computations (Optional).........................................................6-11
Chapter 7 FFT
7.1 Displaying FFT Waveforms .............................................................................................. 7-1
7.2 Measuring FFT Waveforms .............................................................................................. 7-3
Chapter 8 Cursor measurement
8.1 MeasuringwithΔTCursors .............................................................................................. 8-1
8.2 MeasuringwithΔVcursors............................................................................................... 8-2
8.3 MeasuringwithΔTandΔVCursors.................................................................................. 8-3
8.4 Measuring with Marker Cursors (Marker)......................................................................... 8-4
8.5 Measuring with Angle Cursors (Degree) .......................................................................... 8-5
Chapter 9 Automated Measurement of Waveform Parameters
9.1 Automatically Measuring Waveform Parameters ............................................................. 9-1
9.2 Processing Statistics on Automatically Measured Values ................................................ 9-5
9.3 Measuring Enhanced Parameters.................................................................................. 9-10
Chapter 10 Zooming in or out of Waveforms
10.1 Zooming in or out of waveforms ..................................................................................... 10-1
10.2 Zooming in or out of Waveforms in the Vertical Direction............................................... 10-3
Chapter 11 Searching Waveforms
11.1 Searching for Edges........................................................................................................11-1
11.2 Searching with Multiple Input Patterns ............................................................................11-4
11.3 Searching for Pulse Width...............................................................................................11-8
11.4 Searching for Timeout Periods ......................................................................................11-11

vi IM DLM3054-02EN
Contentsの1.1のの16.1のののののののののののの のののののの
Contents
Chapter 12 Analyzing and Searching Serial Bus Signals
12.1 Analyzing and Searching FlexRay Bus Signals (Option) ............................................... 12-1
12.2 Analyzing and Searching CAN Bus Signals (Option) ..................................................... 12-5
12.3 Analyzing and Searching CAN FD Bus Signals (Option) ............................................... 12-9
12.4 Analyzing and Searching LIN Bus Signals (Option) ..................................................... 12-13
12.5 Analyzing and Searching CXPI Bus Signals (Option) .................................................. 12-17
12.6 Analyzing and Searching SENT Signals (Option) ........................................................ 12-22
12.7 Analyzing and Searching UART Signals (Option) ........................................................ 12-29
12.8 Analyzing and Searching I2C Bus Signals (Option)...................................................... 12-35
12.9 Analyzing and Searching SPI Bus Signals (Option)..................................................... 12-40
12.10 Analyzing and Searching User-Defined Serial Bus Signals ......................................... 12-47
12.11 Displaying Multiple Lists ............................................................................................... 12-52
Chapter 13 Waveform Histogram Display
13.1 Displaying Waveform Histograms .................................................................................. 13-1
13.2 Measuring Histogram Parameters.................................................................................. 13-2
Chapter 14 Power Supply Analysis (Power Analysis and Power Measurement,
Option)
14.1 Power supply analysis type ............................................................................................ 14-1
14.2 Analyzing Switching Loss............................................................................................... 14-2
14.3 Performing Safe Operating Area Analysis ...................................................................... 14-5
14.4 Performing Harmonic Analysis ....................................................................................... 14-6
14.5 Measuring the Joule Integral .......................................................................................... 14-9
14.6 Measuring Power ......................................................................................................... 14-10
Chapter 15 Displaying and Searching History Waveforms
15.1 Displaying History Waveforms........................................................................................ 15-1
15.2 Searching History Waveforms ........................................................................................ 15-4
Chapter 16 Printing and Saving Screen Captures
16.1 Loading Roll Paper Into the Built-In Printer (Option) ..........................................................16-1
16.2 Printing on the Built-in Printer (Option)........................................................................... 16-3
16.3 Printing on a USB Printer ............................................................................................... 16-4
16.4 Printing on a Network Printer ......................................................................................... 16-5
16.5 Saving Screen Captures to Files.................................................................................... 16-6
16.6 Printing and Saving Screen Capture Data to Multiple Output Destinations at the Same
Time................................................................................................................................ 16-8
Chapter 17 Saving and Loading Data
17.1 Connecting USB Storage Device to the USB Ports ....................................................... 17-1
17.2 Saving Waveform Data................................................................................................... 17-2
17.3 Saving Setup Data ......................................................................................................... 17-6
17.4 Saving Other Types of Data ........................................................................................... 17-7
17.5 Loading Waveform Data............................................................................................... 17-10
17.6 Loading Setup Data...................................................................................................... 17-12
17.7 Loading Other Types of Data........................................................................................ 17-13
17.8 Performing File Operations .......................................................................................... 17-15

vii
IM DLM3054-02EN
Contentsの1.1のの16.1のののののののののののの のののののの
Chapter 18 Ethernet Communication
18.1 Connecting the Instrument to a Network ........................................................................ 18-1
18.2 Configuring TCP/IP Settings........................................................................................... 18-3
18.3 Accessing the instrument from a PC (FTP Server) ........................................................ 18-4
18.4 Configuring Mail Transmission (SMTP Client Function)................................................. 18-5
18.5 Connecting to a Network Drive....................................................................................... 18-6
18.6 Configuring a Network Printer ........................................................................................ 18-7
18.7 Using SNTP to Set the Date and Time ........................................................................... 18-8
Chapter 19 Other Operations
19.1 Changing the Menu, Message , and USB Keyboard Languages................................... 19-1
19.2 Setting the Click Sound, Measured Value Font Size, and Number of Rows for Displaying
Measurement Values...................................................................................................... 19-2
19.3 Viewing Setup Information (Overview) ........................................................................... 19-3
19.4 Using the Instrument as a USB Storage Device ............................................................ 19-4
Index
Contents

1-1
IM DLM3054-02EN
Chapter 1 Vertical and Horizontal Control
1.1 Setting the Vertical Axis (Analog Signal)
This section explains the following settings for the vertical axis for analog signals:
CH menu
• Turning waveform display on or off
• Input coupling
• Probe
• Turning inverted waveform display on and off
• linear scaling
• Label display
• Bandwidth limit
• Offset
UTILITY menu
• Turning offset cancel on or off
SCALE knob
• Vertical scale
POSITION knob
• Waveform vertical position
► “Vertical Axis (Analog Signal)” in the Features Guide
CH Menu
1. Press a key from CH1 to CH4. The channel key illuminates brightly, and the following menu
appears.
You can also tap MENU ( ) in the upper left of the screen and select the CH menu from VERTICAL on the
top menu that is displayed.
Label display
Linear scaling
Turns the inverted waveform display on and off
Probe
Input coupling
Turns waveform display on or off
Bandwidth limit
Offset
2. If you press a channel key different from step 1, that channel becomes configurable.
The channel key being configured illuminates brightly, and the channel key selected in Step 1 is dark.
Note
• When waveform display is on, channel keys (CH1 to CH4) whose illuminate. You can press channel
keys that are not illuminated to turn their waveform displays on. You can press channel keys that are
illuminated to turn their waveform displays off.
• When the record length (Record Length) of the ACQUIRE menu is set to the maximum record length, the
CH2 and CH4 waveforms cannot be used. For details on the ACQUIRE menu, see section 3.1.

1-2 IM DLM3054-02EN
1.1 Setting the Vertical Axis (Analog Signal)
Input Coupling (Coupling)
AC: Displays the waveform produced from only the AC component of the input signal through
1MΩ.
DC: Displays the waveform produced from both the DC and AC components of the input signal
through1MΩ.
DC50: Displays the waveform produced from both the DC and AC components of the input signal
through50Ω.
Input Coupling Settings and Frequency Response
The frequency responses when the input coupling is set to AC, DC, and DC50 are shown below.
Note that if the input coupling is set to AC, the instrument does not acquire low-frequency signals or
signal components as indicated in the figure below.
0 dB
–3 dB
500 MHz*
Attenuation
0 dB
–3 dB
500 MHz*
Attenuation
About 1 Hz when 1:1 probe is used
1 Hz or lower when 10:1 probe is used
Input frequency Input frequency
If AC is selected If DC or DC50 is selected
* The high-frequency –3 dB point differs according to the model and the voltage scale settings.
CAUTION
• Themaximuminputvoltageinthecaseof1MΩinputis300Vrmsor400Vpeakwhenthe
frequency is 100 kHz or less. Applying a voltage greater than either of these limits may
damage the input section. For frequencies above 100 kHz, damage may occur even if the
voltage is below this value.
• Themaximuminputvoltagefor50Ωinputis5Vrmsor10Vpeak.Applyingavoltage
greater than either of these limits may damage the input section.
• If the input coupling is AC, in accordance with the frequency response, the input signal
is attenuated more in lower frequencies. As a result, even when a high voltage signal
is actually applied, it may not be measured as a high voltage signal. Furthermore, the
over-range indicator may not be displayed on the screen. As necessary, switch the input
coupling to DC to check the input signal voltage.
French
ATTENTION
• Latensiond’entréemaximumpouruneentréede1MΩestde300Vrmsou400Vcrête
lorsque la fréquence est inférieure ou égale à 100 kHz. Le fait d’appliquer une tension
dépassant l’une de ces limites risque d’endommager la section d’entrée. Si la fréquence
estsupérieureà100kHz,desdommagesrisquentdesurvenirmêmelorsquelatensionest
inférieure à cette valeur.
• Latensiond’entréemaximalepouruneentréede50Ωestde5Vrmsou10Vcrête.
L’application d’une tension supérieure à l’une de ces limites pourrait endommager la
section d’entrée.
• Si le courant du couplage d’entrée est alternatif (CA), conforme à la réponse en fréquence,
le signal d’entrée est davantage atténué aux fréquences plus basses. Par conséquent,
mêmesivousappliquéunsignaldetensionélevée,cedernierrisquedenepasêtre
mesuré comme tel. De plus, le voyant de dépassement de plage risque de ne pas s’afficher
à l’écran. Le cas échéant, basculez le couplage d’entrée sur CC (courant continu) afin de
vérifier la tension du signal d’entrée.

1-3
IM DLM3054-02EN
1.1 Setting the Vertical Axis (Analog Signal)
Probe (Probe)
Press the Probe soft key. The following menu items appear.
Deskew value
Execute automatic zero adjustment of current probes
(can only be executed when current probes are connected)
Attenuation
Probe type
Execute the demagnetization and automatic
zero adjustment of current probes.
(Execution is only possible when a YOKOGAWA
PBC100 or PBC050 is connected.)
Note
When a current probe with a YOKOGAWA probe interface (such as a the PBC100 or PBC050 probe) is
connected to the instrument, you can execute demagnetization and automatic zero adjustment from the
instrument.
When you demagnetize and perform automatic zero adjustment on a current probe, do not clamp the
conductor. If you demagnetize a current probe while the conductor is clamped, the current that flows through
the conductor as a result of demagnetization may damage components of the DUT circuitry.
Linear Scaling (Linear Scale)
Press the Linear Scale soft key. The following menu items appear.
Scaling Coefficient (A) and Offset (B)
Unit
Turn linear scaling on or off.
Label Display (Label)
Press the Label soft key. The following menu items appear.
Label
Turns label display on or off
Bandwidth Limit (Bandwidth)
Press the Bandwidth soft key. The jog shuttle controls Bandwidth.
Bandwidth limit

1-4 IM DLM3054-02EN
1.1 Setting the Vertical Axis (Analog Signal)
UTILITY System Configuration Menu
Press UTIL and then the System Configuration soft key. The following menu items appear.
Turns offset canceling on or off
Turning Offset Cancel On or Off (Offset Cancel)
ON: The offset is subtracted from the input signal when cursor measurements, computations, and
other operations are performed.
OFF: The offset is not subtracted from the input signal when cursor measurements, computations,
and other operations are performed.
Vertical Scale (SCALE knob)
1. Press a key from CH1 to CH4 to select the channel that you want to set the vertical scale for.
• The CH key that you press illuminates brightly.
• The LED between the SCALE and POSITION knobs illuminates in the color assigned to the selected
channel (the color around the CH key).
2. Turn the SCALE knob to set the vertical scale.
If you push the SCALE knob, the FINE indicator illuminates, allowing you to set the vertical scale with
higher resolution.
1
2
3
4
LOGIC
FINE indicator
LED
SCALE knob
CH1 to CH4 keys
Displays the vertical scale and input coupling for each channel

1-5
IM DLM3054-02EN
1.1 Setting the Vertical Axis (Analog Signal)
Waveform Vertical Position ( POSITION knob)
1. Press a key from CH1 to CH4 to select the channel that you want to set the vertical position for.
• The CH key that you press illuminates brightly.
• The LED between the SCALE and POSITION knobs illuminates in the color assigned to the selected
channel (the color around the CH key).
2. Turn the POSITION knob to set the vertical position.
You can set the vertical position to 0 V by pressing the POSITION knob.
1
2
3
4
LOGIC
LED
POSITION knob
CH1 to CH4 keys
Note
Preview
• If you change the vertical scale when waveform acquisition is stopped, the waveform is displayed
expanded or reduced vertically.
• If you change the vertical position when waveform acquisition is stopped, the waveform display position
changes.

1-6 IM DLM3054-02EN
1.2 Setting the Vertical Axis (Logic Signal) (On
models with the logic signal input port)
This section explains the following settings for the vertical axis for logic signals:
LOGIC Menu
• Turning waveform display on or off
• Set bits.
Turning bit display on and off, label name, threshold level, and noise rejection
• Bus display
Turning the bus display on or off, bus bit assignment, labels, and format
• State display
Turning state display on or off, clock source, clock source polarity, detection level, hysteresis, and
state assignment
• Bit and bus display order
• Deskewing
SCALE knob
• Display size
POSITION knob
• Vertical position
► “Vertical Axis (Logic Signal)” in the Features Guide
LOGIC Menu
Press LOGIC. The following menu items appear.
You can also tap MENU ( ) in the upper left of the screen and select the LOGIC menu from
VERTICAL on the top menu that is displayed.
Bit and bus
display order
State display
Bus display
Set bits.
Turns waveform display on or off
Deskew value
Note
• If you press the L key when it is not illuminated, the key illuminates, and the LOGIC waveform display
turns on. Logic signal waveforms are displayed in the CH4 waveform display area.
• If you press the LOGIC key when it is illuminated, the key turns off, and the LOGIC waveform display
turns off.
• When the record length (Record Length) of the ACQUIRE menu is set to the maximum record length,
LOGIC waveforms cannot be used. For details on the ACQUIRE menu, see section 3.1.

1-7
IM DLM3054-02EN
1.2 Setting the Vertical Axis (Logic Signal) (On models with the logic signal input port)
Bit Settings (Bit Setup)
Press the Bit Setup soft key. The following screen appears.
For Logic Probes Other Than the 701989
Turns the display on or off for all bits
Display on/off state and label of each bit
Preset threshold levels
Selecting a preset automatically sets the
threshold level.
Threshold level
If you change the automatically specified value,
the preset setting changes to “Userdef.”
For the 701989 Logic Probe
• When the Threshold Type is All
Turns the display on or off for all bits
Display on/off state and label of each bit
Preset threshold levels
Selecting a preset automatically sets the
threshold level.
Threshold level
If you change the automatically specified value,
the preset setting changes to “Userdef.”
Noise rejection
The threshold type is set to All.

1-8 IM DLM3054-02EN
1.2 Setting the Vertical Axis (Logic Signal) (On models with the logic signal input port)
• When the Threshold Type is Each
Turns the display on or off for all bits
Preset threshold levels
• Selecting a preset automatically sets
the threshold level.
• When the threshold type is Each, set
the threshold level for each bit.
Threshold level
• If you change the automatically specified
value, the preset setting changes to “Userdef.”
• When the threshold type is Each, set the
threshold level for each bit.
Display on/off state and
label of each bit
Noise rejection
The threshold type is set to Each.
Note
• For logic probes other than the 701989, the threshold type is All. The setup menu does not appear.
• The Level and Noise Rejection* of Bit Setup are linked with the Level and Noise Rejection* settings when
LOGIC is set as the source in the trigger settings.
* You can set this when the logic probe is 701989.

1-9
IM DLM3054-02EN
1.2 Setting the Vertical Axis (Logic Signal) (On models with the logic signal input port)
Bus Display (Bus)
Press the Bus soft key. The following menu items appear.
FormatLabel
Turns bus display on or off
Bus bit assignment
Bus bit assignment
1. Press the Assignment soft key. The assignment edit screen appears.
2. Press the cursor movement soft key on the Edit menu to move the cursor to the right of the
position where the bit is to be placed.
3. Turn the jog shuttle, or move the SET key up, down, left, or right to select the bit to be placed
from the group of bits.
4. Press SET.
The selected bit is placed to the left of the cursor position.
5. Press the ENTER soft key to confirm the setting.
Assignment
location
Bits
Move the cursor
Delete
Deletes the bit to the right of the cursor
Restores the default settings
Delete all
Confirms the settings
Backspace
Deletes the bit to the left of the cursor
This is the same as pressing the
corresponding soft key on the edit menu.
Cursor
Edit Menu

1-10 IM DLM3054-02EN
1.2 Setting the Vertical Axis (Logic Signal) (On models with the logic signal input port)
State Display (State)
Press the State soft key. The following menu items appear.
Clock source hysteresis
Clock source detection level
Clock source during state display
Turns the state display on and off
State Assignment
Clock source polarity (Polarity)
Clock source bit
Set with the jog shuttle
Set with the jog shuttle
When the clock source is LOGIC
State Assignment
Press the Assignment soft key. The following screen appears.
Turns the display on or off for
all bits and the bus
Turn the display of each bit and
the bus on and off.

1-11
IM DLM3054-02EN
1.2 Setting the Vertical Axis (Logic Signal) (On models with the logic signal input port)
Bit and Bus Display Order (Bit Order)
Press the Bit Order soft key. The following screen appears.
Select a bit or the
bus, and edit the
display order.
Restores the default
settings
Moves the display order down
Moves the display order up
Display order reversal
Reverses the display order
of Bus and Bit7 to Bit0
1. Turn the jog shuttle or move the SET key up and down to select the bit or bus to move.
The selected bit or bus cell is highlighted.
Selected cell
2. Press the Up or Down soft key to move the selected bit or bus up or down.
Every time the selected bit or bus moves up or down, the order of the upper and lower bits or bus is
switched.
When the selected
cell is moved 6
positions downwards
The change affects the bit and bus
display order along the vertical axis
of the screen.
Deskew (Deskew)
Set the adjustment values for the time offsets (skew) between the logic signal and other signals, which
are caused by the use of different types of probes. Deskewing is performed on all eight bits collectively.

1-12 IM DLM3054-02EN
1.2 Setting the Vertical Axis (Logic Signal) (On models with the logic signal input port)
Display Size (SCALE Knob)
1. Press LOGIC to make the SCALE knob control the LOGIC setting.
• The LOGIC key illuminates brightly.
• The LED between the SCALE and POSITION knobs illuminates in the color assigned to the LOGIC
channel (the color around the LOGIC key).
2. Turn the SCALE knob to set the display size.
Vertical Position ( POSITION Knob)
1. Press LOGIC to make the POSITION knob control the LOGIC setting.
• The LOGIC key illuminates brightly.
• The LED between the SCALE and POSITION knobs illuminates in the color assigned to the LOGIC
channel (the color around the LOGIC key).
2. Turn the POSITION knob to set the vertical position.
1
2
3
4
LOGIC
LED
LOGIC key
POSITION knob
SCALE knob