Zcom AS220V2 User manual

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page ii
TABLE OF CONTENTS
Introduction ......................................................................................................................................................... 3Chapter 1.
Product Description .......................................................................................................................................................................................31.1.
Hardware Components ...................................................................................................................................... 4Chapter 2.
Package Contents ...........................................................................................................................................................................................42.1.
Installation Requirements............................................................................................................................................................................42.2.
Physical Ports ....................................................................................................................................................................................................42.3.
If necessary: reset button.............................................................................................................................................................................52.4.
LED Indicator.....................................................................................................................................................................................................52.5.
Hardware Installation ......................................................................................................................................... 6Chapter 3.
Mounting the Access Point .........................................................................................................................................................................63.1.
In-wall mount .........................................................................................................................................................................................63.1.1.
Wall mount ..............................................................................................................................................................................................63.1.2.
Ceiling Mount (Optional accessory_AS-CLM4) ...................................................................................................................................73.2.
Installing the Anti-tamper Lock (Optional accessory_AS-LK18) ...................................................................................................73.3.
Safety Notice.....................................................................................................................................................................................................83.4.
Powering the Access Point ..........................................................................................................................................................................83.5.
The HTTP Interface ............................................................................................................................................. 9Chapter 4.
Login to the HTTP Interface ........................................................................................................................................................................94.1.
Thin AP (TAP) Mode.......................................................................................................................................................................................94.2.
Access Point Configuration...............................................................................................................................................................94.2.1.
Status ...................................................................................................................................................................................................... 104.2.2.
4.2.2.1. Overview...................................................................................................................................................................................... 10
4.2.2.2. General......................................................................................................................................................................................... 11
4.2.2.3. System Log ................................................................................................................................................................................. 12
System .................................................................................................................................................................................................... 124.2.3.
4.2.3.1. AP Mode...................................................................................................................................................................................... 12
4.2.3.2. Reboot.......................................................................................................................................................................................... 12
Technical Specifications ...................................................................................................................................67Chapter 5.
Appendix ............................................................................................................................................................69Chapter 6.
Warranty .......................................................................................................................................................................................................... 696.1.
General Warranty ............................................................................................................................................................................... 696.1.1.
Warranty Conditions......................................................................................................................................................................... 696.1.2.
Warranty service will be excluded if following conditions occurred:........................................................................................ 69
Disclaimer.............................................................................................................................................................................................. 696.1.3.
Compliance..................................................................................................................................................................................................... 706.2.
RF Exposure Warning ....................................................................................................................................................................... 706.2.1.
CE Marking ........................................................................................................................................................................................... 706.2.2.
WEEE Compliance Statement........................................................................................................................................................ 706.2.3.
Declaration of Conformity........................................................................................................................................................................ 706.3.
Optional Accessories................................................................................................................................................................................... 716.4.
Contact Information.................................................................................................................................................................................... 716.5.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 3
INTRODUCTIONChapter 1.
This manual is intended for installing and managing the AS220V2 using the HTTP interface. The
AS220V2 will simply be referred to as the AP (Access Point) within this guide. The installer should
be familiar with network structures, terms, and concepts.
Product Description1.1.
The AS220V2 is a 2x2 dual-band indoor AP (Access Point) that supports the IEEE 802.11ac Wave 2
standard and can provided wireless data rates up to 1.1 Gbps and optimizing the 2.4 GHz and 5
GHz frequency bands. Products details are available on Z-COM website at
https://www.zcom.com.tw/index/product/details?id=7
Designed in compact appearance and provides flexible installations, which blends into any interior
areas. The AS220V2 is equipped with a PoE out capability that enables cost-effective deployment
to smart surveillance applications. The added benefit of the Wi-Fi SON (Self-Organizing Network)
and Bluetooth location services greatly improves management efficiency.
The AS220V2 is the ideal choice for small and medium-sized businesses (SMBs), deployments, such
as offices, hotels, hospitals, and shopping malls.
Standards
IEEE 802.11a/b/g/n/ac
Radio Chains
2.4GHz: 2x2:2
5GHz: 2x2:2
Antenna
Peak Gain
2.4GHz: 3dBi (Embedded)
5GHz: 3.3dBi (Embedded)
Antenna Type
2.4/5GHz: Omni antenna
Interface
2 x 1GbE RJ45 port

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 4
HARDWARE COMPONENTSChapter 2.
Package Contents2.1.
One indoor
access point
One mounting bracket
+ one screw
Two mounting bracket screws
+ screw anchors
One
allen wrench
Installation Requirements2.2.
TERMS OF USE: All Ethernet cabling runs must use CAT5e, 24 AWG (or above) Shielded Twisted
Pair (STP) cabling. In addition, please cut the cable into a proper length, strip the cables on both
ends, and crimp the wires into RJ45 connectors. It is the professional installer’s responsibility to
follow local country regulations, including operation within legal frequency channels, output power,
indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
Physical Ports2.3.
The following physical ports are available on the device).
The following table describes the physical ports that are available on the device from left to right.
Port
Description
WAN/PoE port
The WAN/PoE port operates at 10/100/1000 Mbps at supports an
RJ45 connection.
Supporting PoE In, the AP can receive power through the WAN port
from PSE (Power Sourcing Equipment), rendering the need for a
power supply into the power port unnecessary.
Power Port (DC48V)
A 48V/0.52A power supply can be connected to this port to provide
power to the AP. We provide power adaptor as an optional accessory
for your reference.
Reset Button
If needed, the AP can be factory reset. With a paperclip, press and
hold this button for 10 seconds to reset the AP to the factory default
settings.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 5
Port Description
LAN Port
The LAN port operates at 10/100/1000 Mbps at supports an RJ45
connector.
Supporting PoE Out, the LAN port can supply PoE power to PDs
(Powered Devices) plugged into the LAN port. Up to 10 Watts output
power can be supplied.
If necessary: reset button2.4.
If the access point needs to be reset, please press and
hold the reset button for more than ten seconds to
restore to factory default settings
LED Indicator2.5.
The following table describes the AP status referring to different LED behavior.
Color
Behavior
Description
Red
Steady
Initializing
Flashing
Factory defaults, waiting to be integrated
Blue
Flashing
Device is busy updating its firmware; do not touch or unplug it
Green
Steady
Internet connection detected
Flashing
No internet connection detected

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 6
HARDWARE INSTALLATIONChapter 3.
Mounting the Access Point3.1.
In-wall mount3.1.1.
Determine where you want to mount the device, position the socket into the slot.
Insert the mounting bracket into the socket using
the two screws (included in the packaging).
Slide the device onto the mounting
bracket to finish the installation.
Note: Before lock two screws into the socket, please reserve space up to 15 cm in length
above bracket for installation.
Wall mount3.1.2.
Determine where you want to mount the device, position the mounting bracket onto the wall,
and use a marker to mark the two screw holes on the wall.
Note: Before drill two holes into the wall, please reserve space up to 15 cm in length
above bracket for installation.
Drill the two holes into the wall and insert the two screw anchors (included in the packaging)
into the holes.
Install the mounting bracket onto the wall
using the two screws (included in the
packaging) into the screw plugs in the wall.
Slide the device onto the mounting bracket
to finish the installation.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 7
Ceiling Mount (Optional accessory_AS-CLM4)3.2.
Determine where you want to mount the device, position the mounting bracket onto the ceiling,
and use a marker to mark the two screw holes on the ceiling.
Drill the two holes into the ceiling and insert the two screw anchors (included with ceiling
mount) into the holes.
Note: The thickness of ceiling board should be less than 15mm.
Install the mounting bracket onto the ceiling
using two screws (included in the packaging)
into the screw plugs in the ceiling.
Slide the device onto the mounting bracket
to finish the installation.
Installing the Anti-tamper Lock (Optional accessory_AS-3.3.
LK18)
Slide all the cables through their respective holes on the anti-tamper lock.
Install the mounting bracket; plug all the
cables into their respective ports on the
device before installing the anti-tamper lock.
Position the anti-tamper lock onto the
device and fasten the lock screw clock-wise
with special anti-tamper lock key.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 8
Safety Notice3.4.
1. Do not install the device close to any electrical grounding device or lightning protection
system. Place the device’s own grounding and lightning protection system apart from any
electrical grounding device and lightning protection system as far as possible.
2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the
power adapter by its edge and do not touch any component or printed circuit boards,
especially for module device.
3. Make sure to keep the temperature and humidity of the installation location at an optimal
level.
4. An excellent grounding system guarantees the stable operation of device, as well as to protect
device from lightning, interference and electrostatic discharges.
5. If installed outdoors, the device may be damaged by lightning. We recommend that you install
additional lightning protection devices if necessary, considering the conditions in your area.
6. Supply stable power to the device. Unstable power may cause the device to malfunction. The
device supports PoE power supply and is recommended if the device is installed near grid lines
within less than 100 meters radius.
Powering the Access Point3.5.

By WAN/PoE
Connect the PoE cable into the WAN/PoE IN
port of the device.

By a power adapter
(Optional accessory_ AC-48052)
Connect the power adaptor into the DC port of
the device.
Note: It's available to turn on the access point by either or .
Note: Please wait for 5-10 seconds while powering on.
Note: LAN port provides DC 48V, Max. 208mA, and up to 10W power supply. The positive
side of the 48V is connected to pin 4 and 5, the negative side is connected to pin 7 and 8
for PoE-out.
Note: Do NOT attempt to connect any non-PoE devices to LAN port and make sure the
input power of devices should comply with PoE-out standard.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 9
THE HTTP INTERFACEChapter 4.
The AP can be configured through its supported software interface HTTP. The HTTP interface can
be accessed using any standard web browsing software through any network. This chapter
explains all the elements that are available on the HTTP interface of the AP.
Note: The default Username is root and Password is password.
Note: Click the icon to add a new entry. Click the icon to remove an entry.
Note: Click Reset button to return the parameters on the page to their previously
saved state.
Note: Click Save button to accept and save the modifications made on the page.
Note: Click Save & Apply button to save and apply the modifications made
on the page.
Login to the HTTP Interface4.1.
To access the HTTP interface on the AP, enter the IP address of the AP into the web browser’s
address bar and press the Enter key.
Enter the Username and Password in the respective textboxes and click the Login button. To
return the information, displayed in the textboxes to the defaults, click the Reset button.
In a default access point configuration, the AS420 default AP mode is TAP mode.
Thin AP (TAP) Mode4.2.
The procedure for completing the access point’s essential configuration depends on whether you
want it to be managed by wireless LAN controllers (WLC).
To configure the access point to be managed by the WLC, you must ensure that the APs will be
able to locate and connect to the WLC when powered on. When connected to the network, each
AP is assigned a valid IP address.
Access Point Configuration4.2.1.
In a default access point configuration, the access point default AP mode is TAP mode, and obtains
IP addresses from DHCP Option 43 protocol.
Note: In TAP mode, the AP must be able to go with Wireless LAN Controllers (WLCs) for
bulk configuration and performing other commands of access points. Please refer to WLC
QSG for settings first, then go back to finish the AP configuration.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=49
Step 1. Power on the access point. As the status of LED indicator from flashing change to steady
green, the connection is successful.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 10
Note: Please make sure DHCP server is enabled on the network once accomplished WLC
settings. The access point must receive its IP address through DHCP server.
If the access point cannot connect to the WLC by DHCP broadcast, please refer to the following
optional settings.
Optional: Set up a static IP address
Note: The following procedure assumes that Windows 10 is the operating system.
Procedures for other operating systems are similar.
Step 1. On your computer, configure your network adapter from the “Local Area Connection
“settings as follows:
˙StartControl PanelNetwork & InternetChange Adapter OptionsEthernet
Step 2. Edit the TCP/IPv4 address setting as follows:
˙PropertiesInternet Protocol Version 4 (TCP/IPv4)
Step 3. Select “Use the following IP address”and make the following entries:
˙IP address: 192.168.1.168 (or any available address in the 192.168.1.x network, except
192.168.1.1)
˙Subnet mask: 255.255.255.0
Leave the “Default gateway” and “DNS server” fields empty.
Step 4. Click “OK” to save your changes.
Login into the access point
Step 5. Launch a Web browser; type default URL 192.168.1.1 to connect to the access point.
When a security alert dialog box appears, click OK/Yes to proceed.
Step 6. When login page appears, enter the following: Username: root/Password: password
Step 7. Click login.
Customizing the Wireless Settings
On the Web interface menu, Select StatusGeneral in the menu bar. Check your switchmod item
to select “Connect with via IP”, and setup your WLC IP address on “Wireless Switch Address 1”.
Note: IP address of WLC needs to be assigned (ex. 192.168.1.228) while on operation.
Status4.2.2.
4.2.2.1. Overview
This page is used to provide an overview of the software settings and status of the AP. The
following parameters are available in this section:
Parameter
Description
Kernel Version
Displays the Linux kernel version.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 11
Parameter
Description
Load Average
Displays the average system load calculated over a given period of time of 1,
5 and 15 minutes.
The following parameters are available in this section:
Parameter
Description
Total Available
Displays the total memory supported by the AP in kilobytes and percentage.
Free
Displays the free memory on the AP in kilobytes and percentage.
Cached
Displays the cached memory on the AP in kilobytes and percentage.
Buffered
Displays the buffered memory on the AP in kilobytes and percentage.
The following parameters are available in this section:
Parameter
Description
IPv4 WAN Status
Displays the IPv4 WAN (Wide Area Network) connection status.
Active Connections
Displays the number of active network connections in integers and
percentage.
4.2.2.2. General
Next click the General Button. Once login, first assign a fixed IP address or a DHCP IP to the AP
under Current IP Setting. Under Wireless Switch Setting, select Connect with Wireless Switch via IP
and input the IP address of the AP access controller, then click save & apply to take effect.
Parameter
Description
ipMod
Displays basic mode information of the ipMod.
IPv4 – Select IPv4 mode.
IPv6 - Select IPv6 mode.
Auto – Auto detected if it is IPv4 or IPv6.
DHCP Client
Choose the DHCP Client, which is Close, or Open by default
it will be Open.
Default Gateway
Enter the IPv4 address of the gateway for the interface.
Primary/Secondary DNS Server
Enter primary/secondary DNS server. (if require the second
one)
IPv6 Address
Enter the IPv6 address.
IPv6 Prefix
Enter the IPv6 prefix IP address.
Default Gateway
Enter the IPv6 address of the gateway for the interface.
IPv6 Primary/Secondary DNS Server
Enter primary/secondary DNS server. (if require the second
one)
Switch mod
Displays basic information of the switch mod:
Connect with via DHCP –
connect the AP via DHCP of the
network or provided by the Access controller DHCP IP
address.
IP – Connect the AP via Access controller IP address.
DNS - Displays the MAC address of the interface.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 12
Parameter
Description
Wireless Switch Address 1/2/3/4
Enter wireless access controller IPv4 IP address.
Wireless Switch IPv6 Address1/2/3/4
Enter wireless access controller IPv6 IP address.
Wireless Switch Name1/2/3/4
Enter access controller DNS value.
Management VLAN ID
Enter specific management VLAN ID which is providing
from the Network.
4.2.2.3. System Log
This page is used to display the system log on the AP. Information on this page is useful for
troubleshooting.
System4.2.3.
4.2.3.1. AP Mode
This page is used to displayed and changed AP modes.
•Thin AP - Specifies to use and configure this AP with a wireless controller in the network. The
wireless controller will be responsible for the configuration of this AP. Only a few functions
are available to be configured on this AP in this mode.
•Fat AP - Specifies to use and configure this AP without a wireless controller in the network.
More functions are available to be configured on this AP in this mode.
4.2.3.2. Reboot
Click the Perform reboot link to reboot the device any unsaved configuration.
Fat AP Mode4.3.
A FAT AP is suitable for family and small-scaled networks and provides full features. This Fat AP
is wireless equipment used to control and manage wireless clients. A FAT AP may support both
2.4GHz and 5GHz band in a single logic management domain. This Fat AP is used for wireless
terminals to access a wired network; also it can communicate the bridge between the wireless
clients and wired network. Before configuring the fat AP make sure that AP is in fat AP mode. If the
AP is in Thin AP mode, please change into Fat AP mode and precede the following essential
configuration.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 13
Status4.3.1.
4.3.1.1. Overview
This page is used to provide an overview of the software settings and status of the AP. Please refer
to page 10. The following parameters are available in the DHCP Leases:
Parameter
Description
Hostname
Displays the hostnames of active DHCP clients connected to the AP. DHCP
stands for Dynamic Host Configuration Protocol.
IPv4 Address
Displays the IP addresses of active DHCP clients connected to the AP. IP
stands for Internet Protocol.
MAC Address
Displays the MAC addresses of active DHCP clients connected to the AP.
MAC stands for Medium Access Control.
Lease Time Remaining
Displays the DHCP lease time remaining for the DHCP clients connected
to the AP.
The following parameters are available in the DHCPv6 Leases:
Parameter
Description
Hostname
Displays the hostnames of active DHCPv6 clients connected to the AP.
IPv6 Address
Displays the IPv6 addresses of active DHCPv6 clients connected to the AP.
DUID
Displays the DUID (DHCP Unique Identifier) of active DHCPv6 clients
connected to the AP.
The following parameters are available in the Wireless section:
Parameter
Description
Generic 802.11bgn Wireless
Controller (wifi0)/(wifi1)
Displays information about the generic 802.11bgn wireless controller
(wifi0)/(wifi1).
SSID - Displays the SSID (Ser
vice Set Identifiers) for this wireless
interface. Click on the hyperlink to configure this wireless interface.
For more information, refer to Wireless Overview on page 45.
Mode - Displays the mode of the wireless interface.
Channel -
Displays the wireless channel (frequency) hosted by this
wireless interface.
TX Power - Display the Wi-
Fi transmit power from this wireless
interface.
Bitrate - Display the bitrate provided through this wireless interface.
The following parameters are available in the Associated Stations section:
Parameter
Description
Network
Click on the hyperlink to configure this wireless interface. For more
information, refer to Wireless Overview on page 45.
RX Rate
Displays the RX (receiving) data rate provided to/from the associated
wireless station.
TX Rate
Displays the TX (transmitting) data rate provided to/from the associated
wireless station.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 14
4.3.1.2. Firewall
4.3.1.2.1. IPv4/IPv6 Firewall
This page is used to display the detailed status of the IPv4 and IPv6 firewall features provided on
the AP.
4.3.1.3. Routes
This page is used to display the IPv4/IPv6 routing information. The following parameters are
available in this section:
Parameter
Description
IPv4 Address
Displays the IPv4 address of the ARP (Address Resolution Protocol) entry.
MAC Address
Displays the MAC address of the ARP entry.
Interface
Displays the physical interface that the ARP entry resides on.
The following parameters are available in the Active IPv4/IPv6 Routes section:
Parameter
Description
Network
Displays the physical or logical interface the active IPv4/IPv6 route resides
on.
Target
Displays the target IPv4 network range of the active IPv4/IPv6 route.
IPv4/IPv6 Gateway
Displays the IPv4 gateway address used by the active IPv4/IPv6 route.
Metric
Displays the metric used by the active IPv4/IPv6 route.
4.3.1.4. System Log
This page is used to display the system log on the AP. Information on this page is useful for
troubleshooting.
4.3.1.5. Kernel Log
This page is used to display the kernel log on the AP. Information on this page is useful for
troubleshooting.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 15
4.3.1.6. Realtime Graphs
4.3.1.6.1. Load
This page is used to display the load graph in real time. The following parameters are available in
the Realtime Load section:
Parameter
Description
1/5/15
Minute Load
Displays the 1/5/15-minute load in real time.
•Average - Displays the average measurement for the 1/5/15-minute load.
•Peak - Displays the peak measurement for the 1-minute load.
4.3.1.6.2. Traffic
This page is used to display the inbound and outbound data traffic graph for each physical and
logical interface in real time.
The following parameters are available in bond0/br-lan/eth0/eth0.1/eth0.2/milreg section:
Parameter
Description
Inbound
Displays the inbound data traffic measurement (kilobits and kilobytes per
second) in real time.
•Average - Displays the average measurement for inbound data traffic.
•
Peak - Displays the peak measurement for inbound data traffic.
Outbound
Displays the outbound data traffic measurement (kilobits and kilobytes per
second) in real time.
•Average - Displays the average measurement for outbound data traffic.
•
Peak - Displays the peak measurement for outbound data traffic.
4.3.1.6.3. Wireless
This page is used to display the wireless signal strength and noise graph in real time. The following
parameters are available in signal strength and noise measurement section:
Parameter
Description
Signal/Noise
Displays the wireless signal strength and noise measurement (decibel-
milliwatts) on the wireless interface in real time.
•Average - Displays the average value on the wireless interface.
•
Peak - Displays the peak value on the wireless interface.
The following parameters are available in this section:
Parameter
Description
Phy Rate
Displays the physical wireless data rate (megabytes per second) through the
wireless interface in real time.
•Average - Displays the average physical wireless data rate through the
wireless interface.
•Peak - Displays the peak physical wireless data rate through the wireless
interface.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 16
4.3.1.6.4. Connections
This page is used to display a graphical overview of active network connections in real time. The
following parameters are available in UDP/TCP/Other section:
Parameter
Description
UDP/TCP/Other
Displays the number of UDP (User Datagram Protocol)/TCP (Transmission
Control Protocol) and other (other than TCP/UDP) network connections in real
time.
•Average - Displays the average number of UDP network connections.
•Peak - Displays the peak number of UDP network connections.
The following parameters are available in this section:
Parameter
Description
Network/Protocol
Display the network/Protocol used by the active network connection.
Source/Destination
Displays the source/destination IP address and TCP/UDP port number of the
active network connection.
Transfer
Displays the transfer data rate (bytes and packets) of the active network
connection.
System4.3.2.
4.3.2.1. System
This page is used to display and configure basic system settings like the logging and the date/time
settings.
4.3.2.2. Administration
4.3.2.2.1. Router Password
This page is used to change the password for accessing on the AP.
4.3.2.2.2. SSH Access
The following parameters are available in this section:
Parameter
Description
Port
Enter the TCP/UDP port number for the SSH connection. The default
port number is 22.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 17
4.3.2.3. Scheduled Tasks
4.3.2.3.1. Task Specification
Each line is a separate task written in the specification:
4.3.2.3.2. Crontab Examples
A line in crontab file like below removes the tmp files from /home/someuser/tmp each day at 6:30
PM.
30 18 * * * rm /home/someuser/tmp/*
4.3.2.4. Backup / Flash Firmware
This page is used to backup/restore the configuration or to update the firmware on the AP. A
factory reset of the software configuration can also be performed on this page.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 18
Network4.3.3.
4.3.3.1. Interfaces
After clicking the Add new interface button, the following page will appear:
To configure the WAN/LAN interfaces, click the Edit button.
Note: The following web page take WAN interfaces for example, LAN interfaces are
similar.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 19
4.3.3.1.1. Static Address
This page is used to display and configure the WAN interface settings.
The following parameters are available in this section:
Parameter
Description
Status
Displays basic status information of the interface.
•Port - Displays the interface name. For example, "eth0.2".
•Uptime - Displays the how long the interface is active.
•MAC Address - Displays the MAC address of the interface.
•RX - Displays the RX (receiving) data rate through the interface.
•TX - Displays the TX (transmitting) data rate through the interface.
After clicking the Switch protocol button, the following will appear:

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point User Manual
Page 20
4.3.3.1.1.1. General Setup
The following parameters are available in this section:
Parameter
Description
Status
Please refer to page 19.
Use custom DNS servers
Enter the IPv4 address or domain name of the DNS (Domain Name
System) server for the WAN connection here. More than one entry can
be created.
Accept router
advertisements
Select this option to accept router advertisement on this interface.
Send router solicitations
Select this option to send router solicitations from this interface.
Note: This option is only available if Accept router advertisements are
enabled.
IPv6 address/gateway
Note: This option is only available if Accept router advertisements are
enabled.