Zcom AS220V2 User manual

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
1
Package Contents
One indoor
access point
One mounting bracket
+ one screw
Two mounting bracket screws
+ screw anchors
One
allen wrench
One quick start guide
Installation Requirements
TERMS OF USE: All Ethernet cabling runs must use CAT5e, 24 AWG (or above) Shielded Twisted
Pair (STP) cabling. In addition, please cut the cable into a proper length, strip the cables on both
ends, and crimp the wires into RJ45 connectors. It is the professional installer’s responsibility to
follow local country regulations, including operation within legal frequency channels, output power,
indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
Mounting the Access Point
In-wall mount
Determine where you want to mount the device, position the socket into the slot.

Insert the mounting bracket into the socket using
the two screws (included in the packaging).

Slide the device onto the mounting
bracket to finish the installation.
Note: Before lock two screws into the socket, please reserve space up to 15 cm in length
above bracket for installation.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
2
Wall mount
Determine where you want to mount the device, position the mounting bracket onto the wall,
and use a marker to mark the two screw holes on the wall.
Note: Before drill two holes into the wall, please reserve space up to 15 cm in length
above bracket for installation.
Drill the two holes into the wall and insert the two screw anchors (included in the packaging)
into the holes.

Install the mounting bracket onto the wall
using the two screws (included in the
packaging) into the screw plugs in the wall.

Slide the device onto the mounting bracket
to finish the installation.
Ceiling Mount (Optional accessory_AS-CLM4)
Determine where you want to mount the device, position the mounting bracket onto the ceiling
board.
Use a marker to locate the two screw holes on the ceiling, and drill the two holes into the ceiling.
Note: The thickness of ceiling board should be less than 15mm.

Insert the ceiling screw through the mounting
bracket, ceiling board, and ceiling mount as the
following picture.

Slide the device onto the mounting bracket
to finish the installation.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
3
Installing the Anti-tamper Lock (Optional accessory_AS-LK18)
Slide all the cables through their respective holes on the anti-tamper lock.
Install the mounting bracket; plug all the
cables into their respective ports on the
device before installing the anti-tamper lock.
Position the anti-tamper lock onto the
device and fasten the lock screw clock-wise
with special anti-tamper lock key.
Safety Notice
1. Do not install the device close to any electrical grounding device or lightning protection system.
Place the device’s own grounding and lightning protection system apart from any electrical
grounding device and lightning protection system as far as possible.
2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the
power adapter by its edge and do not touch any component or printed circuit boards,
especially for module device.
3. Make sure to keep the temperature and humidity of the installation location at an optimal
level.
4. An excellent grounding system guarantees the stable operation of device, as well as to protect
device from lightning, interference and electrostatic discharges.
5. If installed outdoors, the device may be damaged by lightning. We recommend that you install
additional lightning protection devices if necessary, considering the conditions in your area.
6. Supply stable power to the device. Unstable power may cause the device to malfunction. The
device supports PoE power supply and is recommended if the device is installed near grid lines
within less than 100 meters radius.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
4
Powering the Access Point
By WAN/PoE
Connect the PoE cable into the WAN/PoE IN
port of the device.
By a power adapter
(Optional accessory_ AC-48052)
Connect the power adaptor into the DC port
of the device.
LED Indicator
Color
Behavior
Description
Red
Steady
Initializing
Flashing
Factory defaults, waiting to be integrated
Blue
Flashing
Device is busy updating its firmware; do not touch or unplug it
Green
Steady
Ethernet connection detected
Flashing
No Ethernet connection detected
In a default access point configuration, the access point default AP mode is TAP mode, and obtains
IP addresses from DHCP Option 43 protocol.
Note: In TAP mode, the AP must be able to go with Wireless LAN Controllers (WLCs) for
bulk configuration and performing other commands of access points. Please refer to WLC
QSG for settings first, then go back to finish the AP configuration.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=49
Step 1. Power on the access point. As the status of LED indicator from flashing change to steady
green, the connection is successful.
Note: Please make sure DHCP is enabled on the network once accomplished WLC
settings. The access point must receive its IP address through DHCP.
Note:
It's available to turn on the access point by either

or

.
Note: Please wait for 5-10 seconds while powering on.
Note: For PoE Out applications, the LAN port provides DC 48V, Max. 208mA, and up to
10W power supply. The positive side of the 48V is connected to pin 4 and 5, the negative
side is connected to pin 7 and 8.
Warning:Do NOT attempt to connect any non-PoE devices to LAN port and make sure
the input power should comply with PoE Out standard.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
5
Note: Switching from DHCP to assign a static IP address or DNS and L2 discovery mode
to the access point, please refer to the user manual for more information.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25
If the access point cannot connect to the WLC by DHCP broadcast, please refer to the following
optional settings.
Optional: Set up a static IP address
Note: The following procedure assumes that Windows 10 is the operating system.
Procedures for other operating systems are similar.
Step 1. On your computer, configure your network adapter from the “Local Area Connection
“settings as follows:
˙StartControl PanelNetwork & InternetChange Adapter OptionsEthernet
Step 2. Edit the TCP/IPv4 address setting as follows:
˙PropertiesInternet Protocol Version 4 (TCP/IPv4)
Step 3. Select “Use the following IP address”and make the following entries:
˙IP address: 192.168.1.168 (or any available address in the 192.168.1.x network, except
192.168.1.1)
˙Subnet mask: 255.255.255.0
Leave the “Default gateway” and “DNS server” fields empty.
Step 4. Click “OK” to save your changes.
Login into the access point
Step 5. Launch a Web browser; type default URL 192.168.1.1 to connect to the access point.
When a security alert dialog box appears, click OK/Yes to proceed.
Step 6. When login page appears, enter the following: Username: root/Password: password
Step 7. Click login.
Customizing the Wireless Settings
On the Web interface menu, Select StatusGeneral in the menu bar. Check your switchmod item
to select “Connect with via IP”, and setup your WLC IP address on “Wireless Switch Address 1”.
Note: IP address of WLC needs to be assigned (ex. 192.168.1.228) while on operation.
Note: If you need a standalone access point, please change to FAP mode.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
6
FAP Mode
The default AP mode is TAP mode, before FAP configurations please change AP mode.
Step 1. Currently in TAP Mode: On the Web interface menu, click SystemAP mode.
Step 2. Select Fat AP from the drop-down list.
Step 3. Click save & apply to take effect.
Note: For FAP mode, please refer to the user manual for more information.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25
Mobile APP
Z-COM offers the App for bridge mode settings. Please research and download it to provision.
If necessary: reset button
If the access point needs to be reset, please press and
hold the reset button for more than ten seconds to
restore to factory default settings.
Technical Specifications
Physical
Dimensions
(L x W x H)
96 x 29.9 x 192 mm
(3.78 x 1.18 x 7.56 in) WAN/PoE In Port One 10/100/1000 Mbps port
Weight
500 grams (1.1 lbs.)
LAN/PoE Out Port
One 10/100/1000 Mbps port
Antenna 2.4GHz: Embedded 2dBi omni antennas
5GHz: Embedded 2.5dBi omni antennas
Power Supply
DC 48V, 0.5A PoE, or DC Jack (optional accessory)
LAN/PoE Out 48V/10 Watts (Max.), Passive PoE (Pairs 4, 5+; 7, 8 Return)
Power Consumption
Max. 12 Watts
Environmental
Temperature
Humidity
Operating
-10°C to 60°C (14°F to 140°F)
10% to 90% (Non-condensing)
Storage
-20°C to 70°C (-4°F to 158°F)
10% to 90% (Non-condensing)

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
7
Compliance
RF Exposure Warning
The antennas used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be located or operating in conjunction with any other
antenna or transmitter.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
Note: This device meets Max. TX power limit per ETSI regulations.
Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz
frequency range within all member states.
WEEE Compliance Statement
European Directive 2012/19/EU requires that the equipment bearing this symbol on the product
and/ or its packaging must not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately from regular household waste streams.
It is your responsibility to dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or local authorities. Correct disposal
and recycling will help prevent potential negative consequences to the environment and human
health. For more detailed information about the disposal of your old equipment, please contact
your local authorities, waste disposal service, or the shop where you purchased the product.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG
8
Declaration of Conformity
Hereby, Z-COM, Inc. declares that the radio devices are in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=56
Optional Accessories
PN Item Picture
AS-CLM4 Ceiling mount + two screws
AS-LK18 Anti-tamper Lock
AC-48052 48 V 0.52A power adapter
Contact Information
All information may be changed by Z-COM at any time without prior notice or explanation to the
user. For further information please refer to our website: www.zcom.com.tw