Zcom SP230 Series User manual

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
Page i

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
1
Package Contents
One outdoor access point
One clamp
Two waterproof cable glands
One quick setup guide
One ground wire
One mounting bracket
+ Four screws
Note: SP230 and SP230-S5 both provides two waterproof cable glands.
Installation Requirements
TERMS OF USE: All Ethernet cabling runs must use CAT5e, 24 AWG (or above) Shielded Twisted
Pair (STP) cabling. In addition, please cut the cable into a proper length, strip the cables on both
ends, and crimp the wires into RJ45 connectors. It is the professional installer’s responsibility to
follow local country regulations, including operation within legal frequency channels, output power,
indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
Mounting the Access Point on the Pole

Attach the mounting bracket to the device
using four screws (included in the packaging).
Securely tighten the screws.

Attach the clamp to encircle pole and the
mounting bracket. Securely tighten the clamp.
Note: Please avoid having obstacles or metal plates surround the access point.

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
2
Two-dimensional Mounting Kit (Optional accessory_SP-MKM5)
Pole-Mount

Attach the intermediate steel plate to the
device using four M5 screws (included in the
packaging). Securely tighten the screws.

Attach the two-dimensional mounting
bracket to the intermediate steel plate using
four M4 screws (included in the packaging).
Securely tighten the screws.

Attach the pole-supported bracket and align the area where the flat head screws will be
attached. Insert two flat head screws into two-dimensional mounting bracket, and tighten
them approximately.
Note: The pole-supported bracket can accommodate up to 6 cm (2.36”) in diameter.
Wall-Mount

Separate it into two parts: half-mounting
bracket and M-type bracket and unscrew
four hex head machine bolts on the two-
dimensional mounting bracket.

Attach the intermediate steel plate to the device
using four M5 screws (included in the
packaging). Securely tighten the screws.

Attach half-mounting bracket to the device
with intermediate steel plate using four M4

Attach M-type bracket to the device onto the
wall, using four M5 screws + screw anchors

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
3
screws (included in the packaging).
Securely tighten the screws.
(included in the packaging). Securely tighten the
screws.

Attach half-mounting bracket to the M-type bracket, then screw four hex head machine bolts.
Securely tighten the screws.
Anti-theft Steel Rope (Optional accessory_SP-CBM5)

Insert three anti-theft screws (included in
the packaging) to the device through the
mounting bracket. Securely tighten these
three screws. Attach the clamp to encircle
pole and the mounting bracket. Securely
tighten the clamp.

Firstly, encircle the Anti-theft steel rope as
following left diagram, then encircle on the pole.
Secondly, insert the last anti-theft screw (included
in the packaging) to the device with anti-theft steel
rope. Securely tighten the screw.

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
4
Grounding Connection & Protect from Lightning
1. Make your device GND port connect to ground wire.
2. The ground wire connects to the earth. In addition, the
grounding wire meets to 6-AWG copper grounding wire.
Safety Notice
1. Do not install the device close to any electrical grounding device or lightning protection system.
Place the device’s own grounding and lightning protection system apart from any electrical
grounding device and lightning protection system as far as possible.
2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the
power adapter by its edge and do not touch any component or printed circuit boards,
especially for module device.
3. Make sure to keep the temperature and humidity of the installation location at an optimal
level.
4. An excellent grounding system guarantees the stable operation of device, as well as to protect
device from lightning, interference and electrostatic discharges.
5. If installed outdoors, the device may be damaged by lightning. We recommend that you install
additional lightning protection devices if necessary, considering the conditions in your area.
6. Supply stable power to the device. Unstable power may cause the device to malfunction. The
device supports PoE power supply and is recommended if the device is installed near grid lines
within less than 100 meters radius.
Installing a Waterproof Cable Gland for Ethernet Port
(Optional accessory_ SP-WP-CM20)
Dismantle all the components of waterproof cable gland, and plug the cable
through it. Thread and assemble one by one: (1) sealing nut (2) plastic ring (3)
rubber (4) locking nut. Securely tighten all the components.
Note: Be sure that grounding is available and that it
must comply with local and national electrical codes.
For additional lightning protection, use lightning rods
and lightning arrestors.

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
5
Powering the Access Point
Connect the PoE cable into the WAN/PoE IN port of the device.
Warning: Do NOT attempt to connect any non-PoE devices to LAN port and make sure
the input power should comply with PoE Out standard.
LED Indicator
Color
Behavior
Description
Red
Steady
Initializing
Flashing
Power / system on
Green
Steady
Ethernet connection detected
Flashing
No Ethernet connection detected
Access Point Configuration
The SP230 default AP mode is TAP mode, which obtains IP addresses from DHCP Option 43
protocol. The SP230-S5 is FAP mode.
Note: In TAP mode, the AP must be able to go with wireless LAN controllers (WLCs) for
bulk configuration and performing other commands of access points. Please refer to WLC
QSG for settings first, then go back to finish the AP configuration.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=49
Step 1. Power on the AP. As the status of LED indicator from flashing change to steady green, the
connection is successful.
Note: Please make sure DHCP is enabled on the network once accomplished WLC
settings. The access point must receive its IP address through DHCP.
Note: Switching from DHCP to assign a static IP address or DNS and L2 discovery mode
to the access point, please refer to the user manual for more information.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25
If the access point cannot connect to WLC by DHCP broadcast, please refer to the following
optional settings.
Optional: Set up a static IP address
Note: Please wait for 5-10 seconds while powering on.
Note: For PoE Out applications, the LAN port provides DC 48V, Max. 208mA, and up to
10W power supply. The positive side of the 48V is connected to pin 4 and 5, the negative
side is connected to pin 7 and 8.

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
6
Note: The following procedure assumes that Windows 10 is the operating system.
Procedures for other operating systems are similar.
Step 1. On your computer, configure your network adapter from the “Local Area Connection
“settings as follows:
˙StartControl PanelNetwork & InternetChange Adapter OptionsEthernet
Step 2. Edit the TCP/IPv4 address setting as follows:
˙PropertiesInternet Protocol Version 4(TCP/IPv4)
Step 3. Select “Use the following IP address”and make the following entries:
˙IP address: 192.168.1.168 (or any available address in the 192.168.1.x network, except
192.168.1.1)
˙Subnet mask: 255.255.255.0
Leave the “Use the following DNS server address” field empty.
Step 4. Click “OK” to save your changes.
Login into the access point
Step 5. Launch a Web browser; type default URL 192.168.1.1 to connect to the access point.
When a security alert dialog box appears, click OK/Yes to proceed.
Step 6. When login page appears, enter the following: Username: root/Password: password
Step 7. Click login.
Customizing the Wireless Settings
On the Web interface menu, Select StatusGeneral in the menu bar. Check your switchmod item
to select “Connect with via IP”, and setup your WLC IP address on “Wireless Switch Address 1”.
Note: IP address of WLC needs to be assigned (ex. 192.168.1.228) while on operation.
Note: If you need a standalone access point, please change to FAP mode.
FAP Mode
The default AP mode is TAP mode, before FAP configurations please change AP mode.
Step 1. Currently in TAP Mode: On the Web interface menu, click SystemAP mode.
Step 2. Select Fat AP from the drop-down list.
Step 3. Click save & apply to take effect.
Note: For FAP mode, please refer to the user manual for more information.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25
Bridge Mode
Bridge mode allows two or more wireless access points to communicate with each for the purpose
of joining multiple LANs. The default AP mode is TAP mode, before bridge mode configurations
please change to FAP mode.

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
7
Note: For bridge mode settings, please refer to the user manual for more information.
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25
Note: Z-COM also offers the App for bridge mode settings. Please research and
download it to provision.
Technical Specifications
Physical
Dimensions
(L x W x H)
151 x 75.5 x 235 mm
(5.94 x 2.97 x 9.25 in) WAN/PoE In Port One 10/100/1000 Mbps port
Weight
1000 grams (2.2 lbs.)
LAN Port
One 10/100/1000 Mbps port
Antenna
SP230
2.4GHz: Embedded 5dBi omni antennas
5GHz: Embedded 5dBi omni antennas
SP230-S5
2.4GHz: Embedded 5dBi omni antenna
5GHz: Embedded 11dBi directional antennas
Power Supply DC 48V, 0.5A PoE
LAN/PoE Out
48V/10 Watts (Max.), Passive PoE (Pairs 4, 5+; 7, 8 Return)
Power Consumption
Max. 12 Watts
Environmental
Temperature Humidity
Operating
-40°C to 70°C (-40°F to 158°F)
10% to 90% (Non-condensing)
Storage
-40°C to 80°C (-40°F to 168°F)
10% to 90% (Non-condensing)
Compliance
RF Exposure Warning
The antennas used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be located or operating in conjunction with any other
antenna or transmitter.

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
8
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
Note: This device meets Max. TX power limit per ETSI regulations.
WEEE Compliance Statement
European Directive 2012/19/EU requires that the equipment bearing this symbol on the product
and/ or its packaging must not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately from regular household waste streams.
It is your responsibility to dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or local authorities. Correct disposal
and recycling will help prevent potential negative consequences to the environment and human
health. For more detailed information about the disposal of your old equipment, please contact
your local authorities, waste disposal service, or the shop where you purchased the product.
Declaration of Conformity
Hereby, Z-COM, Inc. declares that the radio devices are in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=56

SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Outdoor Access Point QSG
9
Optional Accessories
PN
Item
Picture
SP230
SP230-S5
SP-CBM5
Anti-theft steel rope
+ allen wrench + four screws
V V
SP-MKM5
Two-dimensional mounting kit
• Two-dimensional mounting bracket
• Pole-supported bracket
• Intermediate steel plate
• Two flat head screws
• Four self-tapping screws
• Four screw anchors
• Four machine screws (M4)
• Four machine screws (M5)
V V
SP-WP-CM20 Waterproof cable gland V V
Contact Information
All information may be changed by Z-COM at any time without prior notice or explanation to the
user. For further information please refer to our website: www.zcom.com.tw