Zeiss Axiocam 208 color User manual

Instruction Manual
ZEISS Axiocam 208 color / 202 mono
Microscope Camera

ZEISS Axiocam 208 color / 202 mono
Original Manual
Carl Zeiss Microscopy GmbH
Carl-Zeiss-Promenade 10
07745 Jena
Germany
[email protected]
www.zeiss.com/microscopy
Carl Zeiss Suzhou Co., Ltd.
Modern Industrial Square 3-B, No.333 XingPu Road SIP
215126 Suzhou
China
Document Name: Instruction Manual ZEISS Axiocam 208 color / 202 mono
Order Number: 426570-7011-001
Revision: 4
Language: en-US
Effective from: 07/2021
© 2021 Without the prior written consent of ZEISS, this document or any part of it must neither be translated nor reproduced or
transmitted in any form or by any means - including electronic or mechanic methods, by photocopying, recording or by any in-
formation or filing system. The right to make backup-copies for archiving purposes shall remain unaffected thereby. Any viola-
tions may be prosecuted as copyright infringements.
The use of general descriptive names, registered names, trademarks, etc. in this document does not imply that such names are
exempt from the relevant intellectual property laws and regulations and therefore free for general use. This shall also apply if
this is not specifically referred to. Software programs shall entirely remain the property of ZEISS. No program or subsequent up-
grade thereof may be disclosed to any third party, copied or reproduced in any other form without the prior written consent of
ZEISS, even if these copies or reproductions are destined for internal use at the customer's only, the only exception being one
single back-up copy for archiving purposes.
ZEISS reserves the right to make modifications to this document without notice.

ZEISS Content
Content
1 General Information........................................................................ 5
1.1 Introduction........................................................................................................ 5
1.2 Text Conventions and Link Types ........................................................................ 5
1.3 Explanation warning messages and additional information ................................. 6
2 Safety ............................................................................................. 7
2.1 Intended use....................................................................................................... 7
2.2 Prevention of hazards ......................................................................................... 7
2.3 Limitation of liability............................................................................................ 8
2.4 Warranty............................................................................................................. 8
2.5 Warning labels.................................................................................................... 8
2.5.1 Position of the warning labels ............................................................... 9
2.5.2 Meaning of the warning labels.............................................................. 9
3 Technical Data and Conformity....................................................... 10
3.1 Axiocam 208 color.............................................................................................. 10
3.1.1 Specifications ........................................................................................ 10
3.1.2 Spectral Sensitivity................................................................................. 12
3.2 Axiocam 202 mono............................................................................................. 12
3.2.1 Specifications ........................................................................................ 12
3.2.2 Spectral Sensitivity................................................................................. 14
3.3 Applicable Standards and Regulations................................................................. 14
3.3.1 Symbols on the camera......................................................................... 14
3.3.2 Symbols on the adapter ........................................................................ 15
4 Shipment ........................................................................................ 18
4.1 Axiocam 208 color.............................................................................................. 18
4.2 Axiocam 202 mono............................................................................................. 18
5 Connecting the Camera................................................................... 19
5.1 Camera layout and accessories............................................................................ 19
5.1.1 Camera connections.............................................................................. 19
5.1.2 Camera controls.................................................................................... 19
5.1.3 Accessories ........................................................................................... 20
5.2 Mounting the camera to the microscope ............................................................ 22
5.3 Connecting the camera to the power supply....................................................... 22
5.3.1 Powering the camera via microscope .................................................... 23
5.3.2 Powering the camera via mains supply.................................................. 23
5.4 Connecting the camera to a display (without PC) ................................................ 24
5.5 Connecting the camera to a network .................................................................. 24
5.5.1 Connecting camera via Ethernet............................................................ 24
5.5.2 Connecting camera via Wi-Fi adapter .................................................... 25
5.6 Connecting the camera to a certified PC ............................................................. 26
5.7 Function indicator signals.................................................................................... 26
6 On Screen Display (OSD) Menu ....................................................... 27
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 3

 Content ZEISS
6.1 Opening the OSD menu ...................................................................................... 27
6.1.1 Opening menu via camera's operator panel .......................................... 27
6.1.2 Opening menu via microscope stand buttons........................................ 27
6.1.3 Opening menu via network browser ..................................................... 27
6.2 Home menu........................................................................................................ 28
6.3 Settings menu..................................................................................................... 30
6.3.1 Image Settings menu ............................................................................ 31
6.3.2 Microscope System menu ..................................................................... 33
6.3.3 Operating System menu........................................................................ 35
7 Installing Software and Drivers....................................................... 38
7.1 Installing software on PC .................................................................................... 38
7.2 Installing software on iPad .................................................................................. 38
8 Acquiring Images and Videos.......................................................... 39
8.1 Introduction........................................................................................................ 39
8.2 Basic procedure using operator panel ................................................................. 39
8.3 Basic procedure using OSD menu........................................................................ 39
8.4 Image acquisition with Labscope......................................................................... 39
9 Care and Maintenance .................................................................... 40
9.1 Optical system .................................................................................................... 40
9.2 Cleaning the infrared filter or protective glass ..................................................... 40
9.3 Updating the firmware........................................................................................ 40
10 Troubleshooting ............................................................................. 42
10.1 ZEN software ...................................................................................................... 42
10.2 Camera ............................................................................................................... 43
10.3 Labscope ............................................................................................................ 44
11 Disposal and Recycling.................................................................... 45
4 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 1 General Information | 1.1 Introduction
1 General Information
1.1 Introduction
Welcome to the Axiocam 208 color / Axiocam 202 mono user guide.
These cameras are multi-functional digital CMOS cameras for use in light microscopy applications.
To make it easier for you to set up the camera, please follow the instructions in these chapters
step by step.
Content Chapter Content
About this guide Introduction and overview of this manual.
Safety Important information on the safe handling of the camera.
Read this chapter before unpacking and operating the
camera.
Technical data Here you will find your camera's technical data.
Shipment The contents of delivery and optional attachments will be
described here.
Connecting the camera In this chapter, you will find detailed instructions on con-
necting and using the camera.
OSD menu This chapter lists the functions of the On Screen Display
(OSD) menu.
Installing software and drivers Here you will learn how to install the software and camera
drivers.
Acquiring images This chapter provides the basics of image acquisition.
Troubleshooting In this chapter, we have listed some solutions to various
problems. If you are still unable to solve your problem, con-
tact ZEISS support.
Maintenance This chapter describes some measures for the maintenance
and care of your camera. In case of greater damage, always
contact ZEISS support.
Disposal and Recycling Important instructions for disposal and recycling.
1.2 Text Conventions and Link Types
The following text conventions and link types are used:
Text convention Meaning
Click Start.
Press the STANDBY button.
Press [Enter] on the keyboard.
The names of controls and important infor-
mation are shown in bold letters.
Press <Ctrl+Alt+Del> Press several keys on the keyboard simultane-
ously.
Select Tools > Goto Control Panel > Air-
lock.
Follow a path in the software.
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 5

1 General Information | 1.3 Explanation warning messages and additional information ZEISS
Text convention Meaning
Text input Text to be entered by the user
Programming and Macros Anything typed in literally during program-
ming, including, for example, macro codes,
keywords, data types, method names, vari-
ables, class names, and interface names.
Tab.1: Text convention
Link type Meaning
See: Text Conventions and Link Types [ } 5].Link to further information for this topic.
https://www.zeiss.com/corporate/int/
home.html
Link to a website on the internet.
Tab.2: Link types
1.3 Explanation warning messages and additional information
The safety notes in this document follow a system of risk levels, defined in the following manner:
CAUTION
Risk of personal injury
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate personal injury.
NOTICE
Risk of property damage
NOTICE indicates a property damage message. In addition, NOTICE is used for data loss or cor-
rupt data.
Info
Indicates useful additional information. It helps you to make your daily work easier, but it is
optional. There is no risk for personal injury or property damage involved.
6 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 2 Safety | 2.1 Intended use
2 Safety
2.1 Intended use
The Axiocam 208 color and the Axiocam 202 mono are high definition cameras for color and
monochromatic imaging, respectively. They are suitable for use as accessories for educational and
routine microscopy in laboratory environments and for use by trained laboratory personnel. The
cameras have been designed to be used in the field of light microscopy for general observation,
routine work, and simple applications in which a sufficient amount of light is available.
These cameras should only be used for training and research. The images / videos from these
cameras must not be used for the direct generation of diagnostic results.
2.2 Prevention of hazards
The cameras have been manufactured and tested by ZEISS according to the regulations specified
in CE and has left the manufacturer’s premises in perfect working order. In order to ensure that
this condition is maintained and to avoid any risks when operating the system, the user must
comply with any notes and warnings contained in this manual. The manufacturer shall be exempt
from statutory liability for accidents should the operator fail to observe the safety regulations.
CAUTION
Personal Injury
To avoid personal injury, read and adhere to the safety notes below.
4To avoid the risk of fire or explosion, do not use the camera near inflammable liquids or
gases.
4Setup, expansions, re-adjustments, alterations, and repairs must be carried out only by
persons who have been authorized by ZEISS.
4Do not allow any cables, particularly power cords, to trail across the floor, where they can
be snagged by people walking past.
4Protect the cables from excessive heat (e.g. halogen lamps, microscope fluorescence illu-
mination).
4To avoid injuries due to potentially high surface temperatures, do not touch the camera's
surface for a prolonged time.
4Do not position the equipment in a way that makes it difficult to operate or disconnect the
device.
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 7

2 Safety | 2.3 Limitation of liability ZEISS
NOTICE
To avoid equipment damage, data loss, or corrupted data, read and adhere to the safety notes
below.
4Protect the camera against mechanical impact. External damage may affect the operation
of inner components.
4Keep chemicals and fluids away from the camera.
4Make sure there is sufficient ventilation of the camera head. Avoid direct exposure to sun-
light and locations near heat sources (radiators, stoves). Overheating can cause noisy im-
ages.
4Use the camera in a clean and dry location.
4Attach all connectors firmly and securely.
4Use only the accessories supplied by ZEISS, when applicable.
4Use only normal microscope cleaning material to clean the camera housing.
4Contact your local ZEISS service organization if a repair is necessary. Do not disassemble
the camera by yourself, otherwise the warranty will be lost.
4Save all your data, such as images, measurement data, archives, reports, forms and docu-
ments, at regular intervals on an external storage medium. Otherwise it cannot be avoided
that access to this data may be lost as a result of operational errors or hardware defects.
ZEISS accepts no liability for consequential damage resulting from insufficient data protec-
tion.
2.3 Limitation of liability
No warranty shall be assumed by ZEISS during the warranty period if the equipment is operated
without observing the safety regulations. In any such case, ZEISS shall be exempt from statutory li-
ability for accidents resulting from such operation.
2.4 Warranty
ZEISS shall be exempt from any warranty obligations should the user fail to observe the safety reg-
ulations. ZEISS only guarantees the safety, reliability, and performance of the system if the safety
notes are closely observed.
2.5 Warning labels
All points that may pose special risks are additionally marked by warning labels (pictograms) on
the camera. These warning labels indicate possible dangers. They are part of this instruction man-
ual. They are to be kept in a clean and legible state. Warning labels that are damaged or no
longer clearly legible must be replaced immediately. Always observe all warning labels on the
camera.
8 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 2 Safety | 2.5 Warning labels
2.5.1 Position of the warning labels
1
Fig.1: Warning labels on the camera
2.5.2 Meaning of the warning labels
The meaning of each warning label is explained below.
No. Symbol Description
1
Follow the notes in the instruction manual
and the supplied documents. For more infor-
mation, see Prevention of hazards [ } 7].
Tab.3: List of attached Warning Labels
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 9

3 Technical Data and Conformity | 3.1 Axiocam 208 color ZEISS
3 Technical Data and Conformity
3.1 Axiocam 208 color
3.1.1 Specifications
Features Values
Sensor type CMOS sensor with rolling shutter
Sensor Size Diagonal 8.1 mm (1/2.1")
Effective Sensor Pixel Count 8.3 Megapixels: 3840 (H) x 2160 (V)
Pixel size 1.85 μm
Spectral Sensitivity Approx. 400 nm – 700 nm, IR filter RGB
Bayer color mask
Selectable Resolution 3840 x 2160 (Ultra HD, 4K)
1920 x 1080 (Full HD, 1080p)
Gain (Signal Amplification) 1x – 22x adjustable
Digitization 3 x 8 bit / pixel
Exposure Time Range (Integration time) 0.06 ms - 1 s
Image enhancement functions Active denoising, active sharpening, auto
white balance, HDR
Automatic features Automatic exposure and gain regulation at
Ultra HD resolution (4K), fast live image un-
der low light conditions
Status-LED for camera Color coded operation status
Interfaces HDMI for monitor
USB 3.0 Type-C for USB hub, flash drive, Wi-
Fi adapter or PC connection
Ethernet (RJ45) for LAN connection
Micro-D for power and communication with
dedicated stands
Wi-Fi compatibility Via USB Wi-Fi adapter and router
Optical Interface C-mount
Camera control buttons for stand-alone 1x Image capture
1x OSD (On Screen Display menu)
1x Camera factory reset
Stand-alone operation:
§Image storage format
§Video stream format
§Live frame rate via HDMI
§tiff or jpg
§mp4
§30 fps @ Ultra HD (4K)
Maximum live frame rate at configuration: @ 4K (3840 x 2160)
10 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 3 Technical Data and Conformity | 3.1 Axiocam 208 color
Features Values
§HDMI
§Ethernet
§USB 3.0
§30fps
§-
§15 fps
Maximum live frame rate at configuration:
§HDMI
§Ethernet
§USB 3.0
@ 1080p (1920 x 1080)
§30 fps
§30 fps
§27 fps
Max. file size per image .tiff up to: 24 MB (not content dependent)
.jpg up to: approx. 0.5 MB – 3.3 MB (content
dependent)
Size/ Weight Approx. 135 x 97 x 54mm / 590 g
Housing Blue painted aluminum and cooling fins on
the top plate
Registration CE, RoHS, CSA
Power supply via Micro-D interface
Power consumption Max. 9 W (24 V DC, 0.375 A)
Environmental conditions for storage and op-
eration
+10°C to +40°C, max. 75% relative air hu-
midity at 35°C, no condensation, free air cir-
culation required, indoor use
Environmental conditions for transport in
packaging
-40 °C to +70 °C, max. 75 % relative air hu-
midity at 35 °C
Operating systems:
§for ZEN
§for Labscope
§Windows 10 x64 Prof./Ultimate and
higher
§Windows 7/10 x64 Prof./Ultimate and
iOS v12 and higher
Supported Application Software ZEN blue v3.0 and higher (includes ZEN lite/
pro/system)
Labscope v2.9 (win) and v2.8.3 (iOS) and
higher
Order number 426570-9000-000
Info
Computer hardware, operating system, and software may decrease the frame rates. All specifi-
cations are subject to change without notice.
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 11

3 Technical Data and Conformity | 3.2 Axiocam 202 mono ZEISS
3.1.2 Spectral Sensitivity
Relative Spectral Sensitivity
Wavelenght (nm)
Fig.2: Spectral Sensitivity of Axiocam 208 color (incl. IR Filter)
3.2 Axiocam 202 mono
3.2.1 Specifications
Features Values
Sensor Type CMOS sensor with global shutter
Sensor Size Diagonal 13 mm (1/1.23")
Effective Sensor Pixel Count 2.1 Megapixels: 1920 (H) x 1080 (V)
Pixel size 5.86 μm
Spectral Sensitivity Approx. 350 nm – 850 nm, protection glass
(coated)
Selectable Resolution 1920 x 1080 (Full HD, 1080p)
Gain (Signal Amplification) 1x – 16x adjustable
Digitization 12 or 8 bit / pixel
Cooling Passive cooling
Exposure Time Range (Integration time) 0.3 ms - 2 s
Image enhancement functions Active denoising, active sharpening
Automatic features Automatic exposure and gain regulation at
Full HD resolution (1080p), fast live image
under low light conditions
Status-LED for camera color coded operation status
Interfaces HDMI for monitor
12 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 3 Technical Data and Conformity | 3.2 Axiocam 202 mono
Features Values
USB 3.0 Type-C for USB hub, flash drive, Wi-
Fi adapter or PC connection
Ethernet (RJ45) for LAN connection
Micro-D for power and communication with
dedicated stands
Wi-Fi compatibility Via USB Wi-Fi adapter and router
Optical Interface C-mount
Camera control buttons for stand-alone 1x Image capture
1x OSD (On Screen Display menu)
1x Camera factory reset
Stand-alone operation:
§Image storage format
§Video stream format
§Live frame rate via HDMI
§tiff or jpg
§mp4
§30 fps @ Full HD (1080p)
Maximum live frame rate at configuration:
§HDMI
§Ethernet
§USB 3.0
@ 1080p (1920 x 1080)
§30 fps
§30 fps
§27 fps
Max. file size per image 12bit .tiff: 4 MB (one channel, not content
dependent)
8bit .tiff: 2 MB (one channel, not content de-
pendent)
8 bit .jpg: approx. 0.1 MB – 1.3 MB (content
dependent)
Size/Weight Approx. 135 x 97 x 54mm / 590 g
Housing Blue painted aluminum and cooling fins on
the top plate
Registration CE, RoHS, CSA
Power supply via Micro-D interface
Power consumption Max. 9 W (24 V DC, 0.375 A)
Environmental conditions for storage and op-
eration
+10°C to +40°C, max. 75% relative air hu-
midity at 35°C, no condensation, free air cir-
culation required, indoor use
Environmental conditions for transport in
packaging
-40 °C to +70 °C, max. 75 % relative air hu-
midity at 35 °C
Operating systems:
§for ZEN
§for Labscope
§Windows 10 x64 Prof./Ultimate and
higher
§Windows 7/10 x64 Prof./Ultimate and
iOS v12 and higher
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 13

3 Technical Data and Conformity | 3.3 Applicable Standards and Regulations ZEISS
Features Values
Supported Application Software ZEN blue v3.0 and higher (includes ZEN lite/
pro/system)
Labscope v2.9 (win) and v2.8.3 (iOS) and
higher
Order number 426570-9010-000
Info
Computer hardware, operating system, and software may decrease the frame rates. All specifi-
cations are subject to change without notice.
3.2.2 Spectral Sensitivity
Relative Spectral Sensitivity
Wavelength (nm)
Fig.3: Relative Spectral Sensitivity of Axiocam 202 mono
3.3 Applicable Standards and Regulations
Observe the generally applicable local and national safety and accident prevention regulations, as
well as the applicable laws and regulations in your country. The camera and its accessories have
been designed, manufactured and tested to comply with the guidelines and specifications as
named in the following. The accordance to the relevant specification is indicated by a respective
symbol on the unit.
3.3.1 Symbols on the camera
Symbol Description
Conforms to:
§EU Directive 2014/35/EU (LVD)
§2014/30/EU (EMC)
§2015/863/EU (RoHS)
14 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 3 Technical Data and Conformity | 3.3 Applicable Standards and Regulations
Symbol Description
Complies with EU Directive 2012/19/EU
(WEEE)
CSA certificate mark, conforms to:
§CAN/CSA-C22.2 No. 61010-1-12
§UL Std. No. 61010-1 (3rd edition)
Tab.4: List of attached labels concerning standards and regulations
3.3.2 Symbols on the adapter
Symbol Description
Compliance of this power supply with FCC
Part 15, Class B has been demonstrated with
a standard output load. (The FCC law stipu-
lates that system-level testing with the actual
system load is required to demonstrate com-
pliance with the FCC emission limits.)
Japan: Voluntary Control Council for Interfer-
ence (VCCI)
Australia and New Zealand: complies with
AN/NZS 60950.1:2011 Inc A1 EN
55032:2012
Book 60335 up to 36volts
Conforms to:
§UL STD. 60950-1
§UL STD. 1310
Certified to:
§CSA STD C22.2 NO.60950-1
§CSA STD.C22.2 NO.223
Conforms to AAMI STD. ES60601-1, IEC
60601-1-11
Certified to CAN/CSA STD.C22.2 NO.60601-1
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 15

3 Technical Data and Conformity | 3.3 Applicable Standards and Regulations ZEISS
Symbol Description
Limited Power Source
Protected against:
§access to hazardous parts with a wire
§solid foreign objects of a diameter of
1.0mm and greater
§vertically falling water drops when enclo-
sure tilted up to 15°
Complies to the specifications of directive
2011/65/EU Annex VI (ROHS-2) with amend-
ment 2015/863-EU (ROHS-3)
Fuse inside: T 1.6A 250VAC
Semko S-Mark, certified to:
§IEC 60601-1:2005+A1
§EN 60601-1:2006+A1:2013+A12:2014
§IEC 60601-1-11:2015IEC
60601-1-11:2015
§EN 60601-1-11:2015
§EN
60950-1:2006+A11:2009+A1:2010+A12:
2011+A2:2013
JAPAN TUV R-PSE, certified to:
§J60950-1(H26)
§J55022(H22)
Certified to:
§GB4943.1-2011
§GB9254-2008
§GB17265.1-2012
Complies with:
§Section 301 of Energy Independence and
Security Act (EISA)
§Energy Star tier 2 (North America)
§ECP tier 2 (China)
§MEPS tier 2 (Australia)
§Code of Conduct (Europe)
16 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 3 Technical Data and Conformity | 3.3 Applicable Standards and Regulations
Symbol Description
Complies with CHINA SJ/T 11364-2014 (with
a 30 years’ environmental protection use pe-
riod)
Ukraine: UKRSepro
Complies with:
§ТР ТС 004/2011
§ТР ТС 020/2011
Construction of output connector
CE Mark, tested to comply with:
§EN 55032.2012+AC.2013
§EN 61000-3-2.2014
§EN 61000-3-3.2013
§EN 60601-1-2.2015
§EN 55024.2010
Indoor use only
Equipment protected throughout by double
insulation or reinforced insulation
Complies with EU Directive 2012/19/EU
(WEEE)
Tab.5: List of attached labels concerning standards and regulations
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 17

4 Shipment | 4.1 Axiocam 208 color ZEISS
4 Shipment
4.1 Axiocam 208 color
§1x Axiocam 208 color
§1x Power & signal cable, camera to microscope stand (compatible with Aixolab 5 and Axio-
scope 5/7/Vario)
§1x Power adapter with country-specific plug
§1x USB 3.0 cable, Type-C to Type-A
§1x USB 3.0 flash drive, Type-C and Type-A
§1x USB hub, Type-C
Accessories for Stand-Alone and for Usage with Labscope
Order Number Accessory
000000-0626-248 High-Speed-HDMI-Cable, Premium, Resolu-
tion 4K, 2m
000000-0626-246 Optical USB-Scroll Mouse
000000-0626-245 Keyboard, USB, Language DE
000000-0626-267 Keyboard, USB, Language US
426570-9110-000 Wi-Fi dongle package containing Wi-Fi Don-
gle and USB adaptor Type-C to Type-A
4.2 Axiocam 202 mono
§1x Axiocam 202 mono
§1x Power & signal cable, camera to microscope stand (compatible with Aixolab 5 and Axio-
scope 5/7/Vario)
§1x Power adapter with country-specific plug
§1x USB 3.0 cable, Type-C to Type-A
§1x USB 3.0 flash drive, Type-C and Type-A
§1x USB hub, Type-C
Accessories for Stand-Alone and for Usage with Labscope
Order Number Accessory
000000-0626-248 High-Speed-HDMI-Cable, Premium, Resolu-
tion 4K, 2m
000000-0626-246 Optical USB-Scroll Mouse
000000-0626-245 Keyboard, USB, Language DE
000000-0626-267 Keyboard, USB, Language US
426570-9110-000 Wi-Fi dongle package containing Wi-Fi Don-
gle and USB adaptor Type-C to Type-A
18 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001

ZEISS 5 Connecting the Camera | 5.1 Camera layout and accessories
5 Connecting the Camera
5.1 Camera layout and accessories
5.1.1 Camera connections
1 2 3 4
Fig.4: Camera connector panel
No. Name Function
1
Micro-D port Power supply and communication
2
USB 3.0 Type-C Camera control and image data transfer
3
Ethernet port (RJ45) Communication and image data transfer
4
HDMI port Image data transfer to a certified monitor, TV or pro-
jector
5.1.2 Camera controls
1
234
Fig.5: Camera operator panel
Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001 19

5 Connecting the Camera | 5.1 Camera layout and accessories ZEISS
No. Name Function
1
LED function indicator Please see section Function indicator signals [
} 26] for
detail.
2
Camera factory reset
button
Press to reset all parameters to default.
3
Image / video capture
button
Press shortly for capturing an image.
Press for five seconds to start recording a video. Press
again shortly to stop the video recording.
4
OSD menu button Press to open the OSD menu. Press again to close the
OSD menu.
See also
2Acquiring Images and Videos [}39]
5.1.3 Accessories
The following items are required for power supply and use of the ports:
Name Figure Remarks
Power & signal cable, cam-
era to microscope stand
Connection between camera and
compatible microscopes (e.g.: Axio-
scope 5/7 or Axiolab 5, power is sup-
plied via microscope)
Power adapter with coun-
try-specific plug
Power supply from external power
socket if the camera is used with mi-
croscopes other than Axioscope 5/7
or Axiolab 5.
USB 3.0 cable, Type-C to
Type-A
Connection between camera and PC
USB flash drive, Type C and
Type A
Connection to camera (Type-C) or to
USB hub (Type-A) for immediate im-
age and video storage
20 Instruction Manual ZEISS Axiocam 208 color / 202 mono | en-US | Rev. 4 | 426570-7011-001