ZKTeco SF101 User manual

SF series user manual V1.0
SF100 User Manual
Version 1.0

SF series user manual V1.0
Contents
1 Profile .................................................................................................................... 1
1.1 Basic function parameters............................................................................... 1
1.2 Panel introduction ........................................................................................... 2
2. System Installation .............................................................................................. 4
2.1 Installation Notices ......................................................................................... 4
2.2 Device Installation .......................................................................................... 5
2.3 Sketch Map of System Installation.................................................................. 7
3. Connection with the peripheral devices............................................................. 8
3.1 Connection with access controller （only SF101）...................................... 8
3.2 Connection with door lock.............................................................................. 9
3.3 Connections with exit button, alarm, doorbell, and door sensor ....................11
3.4 Power supply..................................................................................................13
4. Basic operations..................................................................................................14
4.1 Enroll a administrator ....................................................................................16
4.2 Enroll a user...................................................................................................17
4.3 User authentication ........................................................................................18
4.4 Delete a user...................................................................................................19
4.5 Delete all users...............................................................................................20
4.6 Fingerprint enrollment sub-flow and overtime judgement sub-flow..............21
5. Communications.................................................................................................23

SF series user manual V1.0
1 Profile
1.1 Basic function parameters
Features
Easy installation, high reliability
Simple and clear operation flow, voice prompts in the operations.
Support the ID / MF card, a wider use range.
Support the backup authentication, stronger function (also with the
extension function).
Basic function parameters are shown as follows:
Power DC12V
Access control device, has the
detection functions such as door
sensor, device dismantled etc.
Function
One Wiegand output (only SF101)
User number 200 (fingerprint, ID card and MF
card)
Record memory 30000 records
USBcommunication
RS232/485 (device monitors the
running)
Fingerprint head Optical fingerprint head
Door bell Support the wired doorbell
Speaker The voice prompts
Buzzer Alarm when the device is dismantled
LED Three-color indicate (Red, green,
All copyrights are reserved -1-

SF series user manual V1.0
blue)
Language Support multi-national voices
Sleep Support the sleep function
Explanation:
1. Access control function: support the access control output, door
sensor alarm, exit button, but not support time segment, duress alarm etc.
It is a comparatively simple access control.
2. Sleep function: during sleeping, the backlight of fingerprint head is
turned off and Led displays, if any key is pressed (except the Bell key),
it will be waked up automatically to work normally.
1.2 Panel introduction
Front panel
Enroll key: it is
also used as
exit key during
the enrollment.
Delete key: it is
also used as
exit key during
the deletion.
Fingerprint
reader
LED:
the indicator light with three colors of red,
finger
buckle
cover
doorbell key
All copyrights are reserved -2-

SF series user manual V1.0
Back panel:
Anti-dismantle button: Send
out the alarm signal through
the terminal when the device
Speaker (mainly used in voice prompt)
Bottom Panel
Reset key
Press this key to restart device if
device can not run normally due to
the error operations or other
accidents.
USB interface
All copyrights are reserved -3-

SF series user manual V1.0
2. System Installation
2.1 Installation Notices
Our products are mass-produced and in accordance with the strict
production and testing standards in China, the United States and the
European Union, but we hope you read the installation notices carefully
before the installation. The company to remind you the proper use, will
greatly improve your use effect and speed. If you don’t read the notes
carefully before the installation, probably because of improper
installation will cause a very serious accident damage, even though
we make every effort to provide you with good service, and you will
have to pay an unnecessary price.
1. Please connect the power supply later after all other wires are
connected well. If the machine cannot run normally, please cut off the
power and then start examination. Please remember: All connection
wires with power will damage the machine accidentally. We won’t
provide maintenance for such damage.
2. Recommend the use of 3A/12V DC power supply to the equipment.
For details, consult the relevant technical staff.
3. Please firstly read explanations of connection terminals carefully
and then connect the wires in strict accordance with the rules, due
to abnormal operations may result in equipment damages, do not
belong to the scope of warranty
4. All external connection wires are forbidden to be bared, both
connections and useless ends of wires must be bandaged with insulating
tape to prevent the accident contact of bared wires, which cause the
machine damage.
All copyrights are reserved -4-

SF series user manual V1.0
5. To prevent excessive instantaneous electrostatic damage to the
machine in winter or the place with a comparatively serious static,
please connect the ground wire firstly, then connect the other wires.
6. If the distance between power supply and machine is long, please
don't use the net cable or other types of lines to take place of power cord.
While selecting power cord, voltage attenuation caused by overlong
transmission distance should be taken into account.
7. When use 485 to organize a network, please use the professional
485 bus and RS232/485 transformer with power, and adopt the bus-type
wiring. If RS485 communication distance is over 300 meters, add a
terminal matched resistor about 120Ωto the RS485 bus.
8. Please use the access control software to connect the machine and
enroll users.
2.2 Device Installation
1）Post the moulding board on the
wall. Drill holes according to marks
on the moulding. (There should be
screw holes and lead wire hole)
2) Take the waterproof glue
away from the rear cover
All copyrights are reserved -5-

SF series user manual V1.0
3) Take the finger buckle
cover away from the device
4) Use screws to fix the device and
waterproof glue on the wall.
5）At last, install the finger buckle
cover well to complete the device
installation.
All copyrights are reserved -6-

SF series user manual V1.0
2.3 Sketch Map of System Installation
1．When a person has passed the status authentication on the access
control device, the device will output the lock control signal to unlock.
2. Door sensor will automatically detect the switch state, when the door
is accidentally opened or the door is not closed well, it will trigger the
alarm signal (switch volume signal)
3. If the access control device is in unusual circumstances such as illegal
demolition etc., it will output the alarm signal (switch volume signal).
4. External wired doorbell can be connected.
5. External exit button can be connected, so it is convenient to open the
door from the indoors.
6. Through RS485/RS232/USB to connect with PC and transfer data to
PC, you can easily manage multiple terminal devices through access
control management software.
Note: The alarm and the wired doorbell are required to connect an
external power supply
All copyrights are reserved -7-

SF series user manual V1.0
3. Connection with the peripheral devices
3.1 Connection with access controller （only SF101）
SF100 as a fingerprint reader, can support various Wiegand format outputs,
and can connect with access controllers of majority manufacturers on the
market. Wiegand output has two modes as follows:
The mode to output user number: Wiegand outputs the fingerprint or
the user number after a successful card authentication, or the instruction
code after a failed authentication.
The mode to output card: Wiegand outputs the got card data, that is,
to output the card data as the original.
Note: 1) The recommended distance between device and access controller
should not be more than 90 meters (If a longer distance or an environment
with interference, please use the Wiegand signal extender).
2) Regardless of whether the device shares power supply with the access
controller, the device must share the ground with the access controller to
guarantee the stability of Wiegand signal.
3) Since SF100 and SF101 can not be used as readers, RLED, GLED, BEEP
are the idle terminals. In addition, SF100 has no Wiegand output, so 12V,
GND, WD0 and WD1 are also the idle terminals.
All copyrights are reserved -8-