ZKTeco SpeedFace V5L QR Series User manual

Quick Start Guide
Version: 1.0
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.
SpeedFace - V5L[QR] Series

Overview
1
Magnetic Tamper
Switch
Reset
Speaker
RS232
RS485
485B
485A
GND
TXD
RXD
GND
TXD2
RXD2
RS232
GND
12V
+12V
GND
IWD0
IWD1
WD0
WD1
TX+
RX+
TX-
RX-
AUX
AL+
AL-
NC1
COM
NO1
BUT
GND
SEN
GND
Lock
Alarm
Exit Button
Sensor
Auxiliary
Input
Ethernet
Power In
Wiegand
In
Wiegand
Out
Note: Not all products have the function with , the real product shall prevail.
SpeedFace-V5L[QR]
Flash
Camera & Palm Collector
5" Touchscreen
Microphone
QR Code Scanner

Overview
2
SpeedFace-V5L[QR][TD]
Thermal Infrared Temperature
Measurement Module
Thermal Imaging Temperature
Detection Module
SpeedFace-V5L[QR][TI]
Installation Environment
Please refer to the following recommendations for installation.
INSTALL INDOORS
ONLY
AVOID INSTALLATION
NEAR
GLASS WINDOWS
AVOID DIRECT
SUNLIGHT
AND EXPOSURE
AVOID USE OF ANY
HEAT SOURCE
NEAR THE DEVICE

KEEP EFFECTIVE
DISTANCE OF
0.3 to 2m
3
Recommended Palm Gestures
Note:
1. Place your palm within 30 to 50 cm of the device.
2. Place your palm in the palm collection area, such that the palm is placed parallel
to the device.
3. Make sure to keep space between your ngers.
KEEP EFFECTIVE
DISTANCE OF
30 to 50 cm
DO NOT KEEP
YOUR FINGERS
CLOSE
Recommended Standing Position
KEEP SPACES
BETWEEN
YOUR FINGERS
DO NOT KEEP
PALM OUTSIDE
COLLECTION AREA
DO NOT KEEP
YOUR FINGERS
FOLD/CURLED
30 to 50cm

orehead emperatur etection
Installation height: 1.55m
(ield iew) othe thermal
imaging de ice: 5
emperature detection distance:
.3m to 1.2m
eight o h ace adapte or
detection: 1.2m to 2m
155C
Specification Standard value Remark
Operating
Environment
Distance
(between face
and device)
Measurement
Accuracy
Indoor, Avoid wind, Avoid
direct sunlight,
16°C to 35°C (60.8°F to 95°F)
30 to 120cm (0.98ft to 3.94ft)
±0.3°C (±0.54°F)
The recommended operating
temperature is 25°C (77°F)
The recommended distance
is 80cm (2.62ft)
This value is tested at a distance
of 80cm or 2.63ft under 25°C
(77°F) environment.
Note: The temperature measurement data is only for reference, and not for any
medical purposes.
Installation Re uirements
The installation requirements and indications associated with the device are given
below:
Indoor constant emperature
n ironment
4

Standalone Installation
Device Installation
TCP/IP
Alarm Smoke
Detector
Lock
Exit Button
Door Sensor
Card
Reader
1 2 3
1.5m
Attach the mounting template sticker to the wall, and drill holes according to the
mounting paper. Fix the back plate on the wall using wall mounting screws.
①
②Attach the device to the back plate.
③Fasten the device to the back plate with a security screw.
Take SpeedFace-V5L[QR][TI] as an example:
①
②
5

ower Connection
12 C
N
N
12
Recommended power supply
thernet Connection
COMM. Ethernet IP Address , input the address and OK
8
7
6RJ 45
5
4
3
2
1
R
R
6
1) 12V ± 10%, at least 00mA.
2) To share the power with other devices, use a power supply with higher current
ratings.
Note: n A , addresses o the server ) and the device must e in the
same networ egment when connecting t io ecurity so tware.

The system supports both Normally Opened Lock and Normally Closed Lock.
The NO Lock (normally opened when powered) is connected with 'NO1' and
'COM' terminals, and the NC Lock (normally closed when powered) is connected
with 'NC1' and 'COM' terminals. The power can be shared with the lock or can be
used separately for the lock, as shown in the example with NC Lock below:
7
Lock Relay Connection
1 e ice not sharing power with the lock 2 e ice sharing power with the lock
Normally Closed Lock
R1 7
N
N
N
N 1
NC1
L
L
+12
N
DC12V
+12
N
R1 7
N
N
N
N 1
NC1
L
L
DC12V
Normally Closed Lock
DC12V
oor ensor it utton larm Connection
N
N
N
N 1
NC1
L
L
ow witch
tor
N

8
TXD
RXD
GND
RS232
Reader
485+
485-
GND
RXD
GND
TXD
RS232
Reader
RS485
Reader
RXD2
TXD2
GND
RXD
TXD
GND
485A
485B
RS485 and RS232 Connection
Wiegand Reader Connection
Wiegand Reader
Access Controller
+12V
IWD1
IWD0
GND
WD1
WD0
Wiegand card reader connects to the top 4 pins of the wiegand terminal and the last
two pins are used by the Access controller, as shown in the followinggure. It sends the
credentials to the device via wiegand communication.
The RS485 and the RS232 lets user connect to multiple readers to the device.Two RS232
and one RS485 can be connected to the terminal, as shown in the gure below.

User Registration
Method 1: Register on the device
When there is no super administrator set in the device, click on to enter the menu.
Add a new user and set User Role to Super Admin, then the system will request for the
administrator’s verication before entering the menu. It is recommended to register a
super administrator initially for security purposes.
Click on > [ ] > [ ] to register a new user. The options includeUser Mgt. New User
entering the user ID and Name, setting User Role, registering Palm, Face, Card
Number, Password and adding Profile Photo.
Main Menu
User Mgt. User Role COMM. System
Data Mgt.Personalize Attendance
Search
Autotest System Info
Access
Control

User Mgt.
New User
All Users
Display Style
Welcome
2021-04-25 14:31
Sundayday
2021-04-25

Enroll Face
Enrolled Successfully
Palm Registration
Enrolled Successfully
1
1
1
1
*****
1
New User
User ID
Name
User Role
Palm
Face
Card Number
Password
Profile Photo
Access Control Role
Normal User
Mike
9