ZOLL Propaq MD User manual

Quick Reference Guide
Controls & Indicators
Auxiliary Power Connection Battery Insertion
Quick
Access
Keys
Alarm Silence/
Reset
Display/Home
Up/Clockwise
Down/
Counterclockwise
Select
Snapshot
NIBP Start/Stop
Ready For Use
Indicator
3
Shock
2
Charge
1
Select
Energy
SyncPacerBattery
Charge
LED
Auxiliary
Power
LED
Data
Transfer
LED
Equipment Alert
LED
Patient Alarm
LED Power Button
Align arrow with dot and
push connector until it locks.
Align battery with battery well
and push battery into place.
9652-0370-01 Rev. B

Quick Reference Guide
1. Press & to highlight the patient mode field at the top of
the display. Press .
2. Press & to highlight correct patient mode. Press .
Neonate: Birth through 28 days, or 44 weeks gestational
Pediatric: 29 days through 12 years
Adult: 12 years or greater
Changing Patient Mode
Press to cycle through the different screens.
Changing Screen Views
Press to cycle through the different screen brightness options.
Changing Display Brightness
Taking a Monitor Snapshot
Press to take a monitor snapshot. The unit records all
waveforms for 12 seconds before and after pressing the button, and
stores the numeric data on display when the button is pressed.
Note: also acts as a Home key while a menu is displayed.
Normal Mode NVG Friendly ModeHigh Contrast Mode
Waveform Screen Trends Screen Large Numerics Screen

Quick Reference Guide
Apply ECG electrodes.
ECG Monitoring
Press to cycle through leads until the desired lead is displayed.
Changing the Lead Source in Waveform Trace 1
1. Press & to highlight the
Source Label above the waveform.
Press .
2. Press & to highlight the
desired lead source. Press .
Changing the Lead Source in Waveform Trace 1-4
1. Press & to highlight the
Gain Label above the waveform.
Press .
2. Press & to highlight the
desired waveform size.
Press .
Changing the Waveform Gain
5-Lead Electrode Placement3-Lead Electrode Placement
1. Press & to highlight the HR numeric. Press .
2. Press to highlight the ECG Sweep Speed. Press .
3. Press & to highlight the desired sweep speed. Press .
Changing the ECG Sweep Speed
I, II,
III...

Quick Reference Guide
Apply ECG electrodes.
12-Lead ECG Monitoring
1. Press to enter
12-lead mode.
2. Check for a good
quality signal and
ensure all leads
are displayed.
3. Press .
4. Keep the patient still
during the 10-second
acquisition period.
Acquiring a 12-Lead ECG Snapshot
1. Press to display the 12-Lead Review menu.
2. Press & to highlight the desired 12-lead snapshot.
Press .
Reviewing a Stored 12-Lead Snapshot
Changing Displayed Leads in a 12-Lead Snapshot
Press to print the displayed 12-lead snapshot.
Printing a 12-Lead Snapshot
V-Lead Electrode PlacementLimb Lead Electrode Placement
Jugular Notch
Angle of Louis
Press to change the displayed leads for a 12-lead snapshot.
12
I, II,
III...
12

Quick Reference Guide
1. Select the correct size cuff.
2. Attach the cuff to the NIBP hose.
3. Attach the hose to the Propaq MD unit.
4. Apply the cuff to the patient’s limb.
5. Place the limb at the same level as the patient’s heart.
6. Verify the correct patient mode on the Propaq MD unit.
Preparing for NIBP Monitoring
1. Press to initiate a manual NIBP reading.
Initiating an NIBP Reading
1. Press & to
highlight the NIBP
numeric. Press .
2. Press to highlight
NIBP Mode. Press .
3. Press & to
toggle to Auto Mode.
Press .
Setting Up Automatic NIBP Readings
Changing the NIBP Auto Interval
1. Press & to highlight the NIBP numeric. Press .
2. Press & to highlight NIBP Auto Mode Interval (mode
must be set to Auto). Press .
3. Press & to highlight desired interval. Press .
Single Lumen Hose Connection Dual Lumen Hose Connection

Quick Reference Guide
1. Connect the appropriate sensor cable to
the Propaq MD unit.
2. Apply probe to patient.
The pleth waveform and oxygen saturation
value will automatically appear on the
screen when a signal has been detected.
SpO2Monitoring
1. Press & to highlight
the Gain Label above the pleth
waveform. Press .
2. Press & to highlight
the desired waveform size.
Press .
Changing the Waveform Gain
1. Press & to highlight the
Source Label above the pleth
waveform. Press .
2. Press to highlight Remove.
Press .
Removing the Pleth Waveform
SpO2Probe Connection
Note: You can add the pleth waveform back to the display by
selecting Insert from the Source Label menu or by reconnecting the
sensor to the Propaq MD unit and the patient.

Quick Reference Guide
1. Slide open the CO2inlet port cover on the Propaq MD unit.
2. Insert the fitting at end of the sampling line into the inlet port.
3. Rotate the fitting clockwise to tighten.
4. Attach sampling line to patient or endotracheal tube.
Connecting the CO2Sampling Line
Press to initiate CO2monitoring.
Note: A green LED appears when CO2is on, and the unit
automatically displays the capnogram and the EtCO2value.
Starting CO2Monitoring
1. Press & to highlight the
Scale Label above the CO2
waveform. Press .
2. Press & to highlight the
desired waveform size.
Press .
Changing the Waveform Scale
1. Press & to highlight the CO2numeric. Press .
2. Press to highlight the CO2/Resp Sweep Speed. Press .
3. Press & to highlight the desired sweep speed. Press .
Changing the CO2Sweep Speed
Slide open door & insert fitting Rotate fitting to tighten
CO
2
CO
2

Quick Reference Guide
1. Press & to highlight the parameter label for the alarm you
want to set (e.g., HR/PR). Press .
2. Press & to highlight the desired parameter alarm (e.g.,
HR/PR Alarm). Press .
3. Press & to highlight the alarm setting you want to
modify (e.g., HR/PR Upper Limit Enable). Press .
4. Press & to adjust the setting to the desired value
(e.g., On). Press .
5. Press & to highlight the alarm limit you want to modify
(e.g., HR/PR Upper Limit). Press .
6. Press & to adjust the setting to the desired value
(e.g., 120). Press .
Note: An alarm must be enabled (turned on) before the alarm limit
can be adjusted.
Enabling Individual Alarms & Setting Alarm Limits
1. Press .
2. Press to bring up the Alarm Settings Control Panel.
3. Follow steps 2-6 above to enable alarms and set limits.
Note: When any parameter alarm limit is disabled (turned off), the
message SOME ALARM LIMITS DISABLED will appear on the display.
Enabling Multiple Alarms & Setting Alarm Limits
Press to silence an active alarm.
Silencing an Active Alarm
Limits

Quick Reference Guide
1. Connect therapy (MFC) cable to device.
2. Connect therapy cable to hands-free therapy electrodes.
3. Connect hands-free therapy electrodes to patient.
4. Press to select desired energy.
5. Press to charge the Propaq MD unit.
6. After the Propaq MD unit is charged, stand clear and press
to deliver energy.
Performing Defibrillation
While the Propaq MD unit is charging or charged, press to
safely disarm the energy. Changing the selected energy will also
disarm the Propaq MD unit.
Disarming the Defibrillator
1. Press to activate Sync mode. Verify sync marker is placed
over the R-wave.
2. Press to select desired energy.
3. Press to charge the Propaq MD unit.
4. After the Propaq MD unit is charged, stand clear then press and
hold to deliver energy.
Performing Synchronized Cardioversion
Disarm

Quick Reference Guide
1. Press to bring up the Pacer menu.
2. Confirm Pacer Mode and Pacer Rate.
3. Press & to highlight Start Pacer.
4. Press to begin pacing.
5. Press & to highlight the Pacer Output. Press .
6. Press & to adjust the pacer output until capture occurs,
then decrease the output to the lowest level that still maintains
capture.
7. Press to exit the Pacer menu.
Starting the Pacer & Changing Pacer Settings
1. Press to bring up the Pacer menu.
2. Press & to highlight Pause Pacer.
3. Press to pause the pacer.
Pausing the Pacer
1. Press to bring up the Pacer menu.
2. Press & to highlight Turn Pacer Off.
3. Press to turn the pacer off.
Turning Off the Pacer
Pacer
Pacer
Pacer