Zoofari ZTS 10 B16 User manual

Animal Clippers ZTS 10 B1
6
Animal Clippers
Operating instructions
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
www.kompernass.com
ID-Nr.: ZTS 10 B1-01/11-V2
IAN:63807
CV_63807_ZTS10B1_LB6.indd 1-3CV_63807_ZTS10B1_LB6.indd 1-3 28.02.2011 10:17:01 Uhr28.02.2011 10:17:01 Uhr

A
B
ZTS 10 B1
 
 
 
12
3
4
CV_63807_ZTS10B1_LB6.indd 4-6CV_63807_ZTS10B1_LB6.indd 4-6 28.02.2011 10:17:07 Uhr28.02.2011 10:17:07 Uhr

Animal Clippers 2
Read these operating instructions carefully before using this appliance for the first time and preserve
this booklet for later reference. Pass this booklet on to whoever might acquire the appliance at a
later date.
- 1 -
IB_63807_ZTS10B1_LB6.indd Abs1:1IB_63807_ZTS10B1_LB6.indd Abs1:1 28.02.2011 16:27:56 Uhr28.02.2011 16:27:56 Uhr

- 2 -
Animal Clippers
Intended use
These animal clippers are intended exclusively for
the cutting and trimming of animal hair in domestic
households. This appliance is not intended for use
in commercial/industrial applications. Usage other
than as described here is not permitted and may
cause damage or injury. For damage resulting from
misuse or improper handling, the use of force
or unauthorized modification, no liability will be
assumed.
Safety instructions
To avoid the risk of accidents and
injuries:
• This appliance is not intended for use by
individuals (including children) with restricted
physical, physiological or intellectual abilities or
deficiences in experience and/or knowledge
unless they are supervised by a person respon-
sible for their safety or receive from this person
instruction in how the appliance is to be used.
• Children should be supervised to ensure that
they do not play with the appliance.
• Use only the original accessory parts for this
device.
• Check the cutting head for proper function
before using the appliance.
• Never use the appliance with a damaged or
broken trimming guide. The absence of teeth on
the trimming guide can lead to injury.
• Switch the appliance off before you put it down.
To avoid the risk of an electric shock:
• Connect the appliance only to correctly
installed and earthed mains sockets that are
easily accessible. Ensure that the rating of the
local power supply tallies completely with the
details given on the rating plate of the device.
• Ensure that the power cable does not become
damaged. Protect the power cable from sources
of heat and ensure that it cannot be damaged.
• To avoid risks, arrange for defective plugs and/
or cables to be replaced at once by qualified
technicians or our Customer Service Department.
• Do not use the appliance in the close vicinity
of a bath/shower or a sink filled with water.
The proximity of moisture presents a danger,
even when the appliance is switched off.
• NEVER submerse the appliance in water or
other liquids.
• Should the appliance be dropped into water,
ABSOLUTELY disconnect the plug from the
mains socket before extracting the appliance.
• After use or when cleaning it, ALWAYS remove
the plug from the mains power socket. Do not
pull on the power cable directly, pull the plug.
• The appliance is suitable for use only in dry
areas.
• Attention! Keep the appliance dry.
• Do not use the unit while the animal is being
bathed or when the fur is wet.
Items supplied
Animal clippers with blade guard
6 Trimming guides
Cleaning brush
Blade oil
This operating manual
Technical Data
Power supply: 230 V~/50 Hz
Power consumption: 10 W
Protection class: II /
Operating temperature: + 5 °C - + 40 °C
Storage temperature: 0 °C - + 40 °C
IB_63807_ZTS10B1_LB6.indd Abs1:2IB_63807_ZTS10B1_LB6.indd Abs1:2 28.02.2011 16:27:56 Uhr28.02.2011 16:27:56 Uhr

- 3 -
CE- Conformity
This device complies, in regards to conformance with
the basic requirements and other relevent regulations,
with the EMC Directive 2004/108/EC, as well as the
Directive for Low Voltage Devices 2006/95/EC.
Description of the appliance
Appliance (Fig. A)
1Cutting head
2Suspension loop
3On/Off switch
4Adjusting lever
Trimming guides and accessories (Fig. B)
1/8“ (3 mm Cutting length)
1/4“ (6 mm Cutting length)
3/8“ (9 mm Cutting length)
1/2“ (13 mm Cutting length)
Trimming guide for side step cut (right)
Trimming guide for side step cut (left)
Blade cover
Cleaning brush
Blade oil
Operation
The fur to be cut must be dry and clean. Brush the
fur through to remove any knots.
•
Remove the blade guard from the cutting
head 1.
•Place the required trimming guide ( - )
with the prongs facing upwards on the cutting
head 1and thereby press the flap of the trim-
ming guide down firmly onto the lower metal
edge of the cutting head (see illustration).
• Ensure that the trimming guide has properly
engaged and is secured before starting to cut/
trim the fur.
Note:
It is recommended that you begin by trimming a
small area to test the individual trimming guides.
Start with a trimming guide for long fur and, if neces-
sary, change to a shorter one. The trimming guides
allow an average cutting length from 3 -13 mm.
•
Switch the appliance on by sliding the On/Off
switch 3to the position „ON“.
• Slowly run the appliance through the fur against
the direction of hair growth. Hold the appliance
so that the trimming guide is as flat as possible
against the animal.
• Additionally, using the adjusting lever 4,
the cutting depth of the cutting head 1can
be adjusted stepwise (approx. 2 mm) without
changing the trimming guide.
To do this, press the adjusting lever 4back-
wards to increase the cutting length in steps.
Through this, the cutting length of the respective
attached trimming guide will also be increased
by up to 2 mm.
Press the adjusting lever 4forwards to reduce
the cutting length or to bring the trimming guide
back into its original position.
• Through removal of the individual trimming
guide, i.e. using only the cutting head 1itself,
you can cut clean contours.
• After use, switch the appliance off by sliding the
On/Off switch 3to the position „OFF“.
Cleaning and Care
Risk of electric shock
Before cleaning, remove the plug from the mains
power socket.
NEVER submerse the appliance in water or other
liquids.
• Take the respective trimming guide, if fitted, off.
•
Using exclusively the cleaning brush , remove
the hairs from the cutting head 1. The cutting
head 1may not be cleaned with water or
other liquids, except medical alcohol!
•
If in regular use, the cutting head 1should be
oiled occasionally. For this, use the supplied
blade oil .
• Remove excess oil with a dry cloth.
• Clean the housing with a soft, dry lint-free cloth.
• Store the appliance in a dry and dust free
location. When it is in storage, place the blade
guard on the cutting head 1.
IB_63807_ZTS10B1_LB6.indd Abs1:3IB_63807_ZTS10B1_LB6.indd Abs1:3 28.02.2011 16:27:56 Uhr28.02.2011 16:27:56 Uhr

- 4 -
Disposal
Do not dispose of the device in your
normal domestic waste. This product is
subject to the provisions of European
Directive 2002/96/EC.
Dispose of the appliance over a registered waste
disposal firm or at your local community waste
disposal facility. Observe the currently applicable
regulations. In case of doubt, please
contact your waste disposal centre.
Dispose of all packaging materials in an
environmentally friendly manner.
Warranty and Service
You receive a 3-year warranty for this device as
of the purchase date. This appliance has been
manufactured with care and meticulously examined
before delivery.
Please retain your receipt as proof of purchase.
In the case of a warranty claim, please make con-
tact by telephone with our service department.
Only in this way can a post-free despatch for your
goods be assured.
The warranty covers only claims for material and
manufacturing defects, not for transport damage,
worn parts or for damage to fragile components,
e.g. switches or batteries. This product is for private
use only and is not intended for commercial ap-
plications.
In the event of misuse and improper handling,
use of force and interference not carried out by
our authorized service branch, the warranty will
become void.
Your statutory rights are not restricted in any way
by this warranty.
The warranty period is not extended by repairs
effected under warranty. This applies also to
replaced and repaired parts. Damages or defects
discovered after purchase are to be reported
directly after unpacking, at the latest two days after
the purchase date. Repairs carried out after lapse
of the warranty period are subject to charge.
Service Great Britain
Tel.: [phone] (£ 0.10 / minute)
E-Mail: k[email protected]
Service Ireland
Tel: [phone]
(0,082 EUR/Min., (peak))
(0,064 EUR/Min., (off peak))
E-Mail: k[email protected]
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
44867 BOCHUM, GERMANY
www.kompernass.com
IB_63807_ZTS10B1_LB6.indd Abs1:4IB_63807_ZTS10B1_LB6.indd Abs1:4 28.02.2011 16:27:56 Uhr28.02.2011 16:27:56 Uhr