3M PPS Series 2.0 User manual
Insert the 3M™ PPS™ Series 2.0 Spray Cup
System disposable liner into the 3M™ PPS™
Series 2.0 Spray Cup System mixing cup.
1
2Pour material to be sprayed into the 3M™
PPS™ Series 2.0 Spray Cup System mixing
cup. Stir as needed.
4Turn until tight. Insert 3M™ PPS™ Series
2.0 Spray Cup System sealing plug prior to
shaking or sealing.
5Attach spray gun to lled 3M™ PPS™ Series
2.0 Spray Cup System cup.
3Place the 3M™ PPS™ Series 2.0 Spray Cup
System lid with built-in lter on top of the
3M™ PPS™ mixing cup with liner and snap
into place.
Adding the 3M™PPS™Series 2.0 Spray Cup
System Components
2Attach the nozzle to the spray gun with
the locking collar fully connected. Note:
It is easier to install the nozzle while pulling
the trigger backward toward the spray gun
handle. To remove the nozzle from the spray
gun, reverse the process.
4Once the spray gun is properly assembled
you may attach the air line.
3Attach 3M™ PPS™ Series 2.0 spray cup
to nozzle.
2.0 1.8 1.6 1.4 1.3 1.2
Direct Gloss
Single Stage Top Coat
Wet on Wet Primer
High Viscosity Coatings
Sprayable Fillers
Primer Surfacer
Solvent Base Color
Primer Sealer
High Build Primer
Clearcoat
Waterborne Base Coat
WARNING! Do not immerse spray gun or nozzles in cleaning solvents or gun washers. The maximum operational air pressure of this HVLP spray gun is 20 psi/ 1.38 bar.
Nozzle Recommendation
*Starting points only, refer
to Paint Manufacture for
recommendation on fluid
tip size
Recommended Set Up Starting Points
Fan Control Knob: Open 2 rotations from closed position
Fluid Control Knob: Open 4 rotations from closed position
Air Flow control valve: 18-20 psi / 1.24 – 1.37 Bar
See manual for additional use and health and safety information.
bottom of the gun.
1
Attach the supplied air ow valve to the
Assembly
Maximum Operating Air Pressure: 20 psi | 1.38 bar
3M™ Performance Spray Gun HVLP – Gravity
Attach Fluid Hose Whip to base of spray gun.
2
1Attach the supplied air ow valve to the bottom of the gun.
4Connect hose whip to nozzle.
5Attach fluid and pressure lines from bulk feed system (or pressure pot) Note: Utilize the optional
manual fluid shut-off valve, if desired, between hose whip and fluid supply
3Attach the nozzle to the spray gun with the locking collar fully connected. Note: It is easier to
install the nozzle while pulling the trigger backward toward the spray gun handle.
Cleaning
1.1 1.4 1.8
Base Coat / Single Stage Materials
Release Agents
1K Top Coats
2K Top Coats
Clear Coats
Textured Paints
Epoxy / Urethanes Primers
Adhesives
Nozzle Recommendation
*Starting points only, refer to Paint Manufacture for recommendation on fluid tip size
Assembly
3M™ Performance Spray Gun HVLP – Pressure
Maximum Operating Air Pressure: 18 psi / 1.24 bar
Maximum Operating Fluid Pressure: 50 psi/ 3.44 bar.
Recommended Set Up Starting Points
Fan Control Knob: Open 2 rotations from closed position
Fluid Control Knob: Open 4 rotations from closed position
Air Flow Control Valve: 18 psi / 1.24 bar.
Once the system is adequately flushed (pot, lines), depressurize the system (or close the
optional fluid valve)
After pressure is relieved, remove the hose whip from the nozzle.
Remove nozzle from spray gun to clean residue from the nozzle. Rinse out and flush
cleaning solvent through the nozzle with fluid tip pointed straight down into receptacle
to collect waste solvent.
Wipe needle tip. Store spray gun with a nozzle attached to protect the needle.
1
2
4
3
Pressure
Gravity
1
2
4
3
Once coating application is complete, disconnect the air hose from the gun.
To drain back paint into cup - Invert cup, pull trigger, and tap the PPS™ cup on a table
3 times.
Rinse out nozzle spout and flush cleaning solvent through the nozzle by pulling trigger
with fluid tip pointed straight down into receptacle to collect waste solvent.
Store spray gun with a nozzle attached to protect the needle.
The maximum operational air pressure of this HVLP spray gun is 18 psi/1.24 bar.
The maximum operational fluid pressure is 50 psi/ 3.44 bar.
WARNING!
Do not immerse spray gun or nozzles in cleaning solvents or gun washers.
See manual for additional use and safety information.
For additional questions, contact your local 3M representative.
www.3Mbodyshop.co.uk
Phone: +353 12160301
The Iveagh Building, The Park Carrickmines, Dublin 18
3M Ireland Limited Automotive Aftermarket
www.3Mbodyshop.co.uk
Phone: +44 (0)161 237 6391
3M Centre, Cain Road, Bracknell, RG12 8HT
3M United Kingdom plc Automotive Aftermarket
Please recycle. Printed in the UK.
3M and PPS are trademarks of 3M Company © 3M2020. All rights reserved.
Other manuals for PPS Series 2.0
3
Other 3M Paint Sprayer manuals
