3One data PS5026G-2GS-24PoE User manual

PS5026G-2GS-24PoE User Manual
PS5026G-2GS-24PoE
Managed Full Gigabit
Industrial Ethernet PoE Switch
User Manual
Version 1.0, 2017.8.29

PS5026G-2GS-24PoE User Manual
1
Table of Contents
Chapter 1 Product Introduction............................................................................ 4
1.1 Product Overview.......................................................................................... 4
1.2 Features.......................................................................................................... 4
1.3 External Component Description................................................................ 5
1.3.1 Front Panel..............................................................................................................5
1.3.2 Rear Panel.............................................................................................................. 6
1.4 Environment................................................................................................... 6
1.5 Package Contents......................................................................................... 7
Chapter 2 Installing and Connecting the Switch.............................................. 8
2.1 Installation.......................................................................................................8
2.1.1 Desktop Installation............................................................................................... 8
2.1.2 Rack-mountable Installation in 19-inch Cabinet............................................... 9
2.1.3 Power on the Switch..............................................................................................9
2.2 Connect Computer (NIC) to the Switch................................................... 10
Chapter 3 How to Login the Switch....................................................................11
3.1 How to Login the Switch............................................................................. 11
Chapter 4 Switch Configuration..........................................................................13
4.1 Quickly Set................................................................................................... 13
4.2 PORT.............................................................................................................16
4.2.1 Basic Config..........................................................................................................16
4.2.2 Port Aggregation.................................................................................................. 17
4.2.3 Port Mirroring........................................................................................................18
4.2.4 Port Limit............................................................................................................... 20
4.2.5 Storm Control....................................................................................................... 21
4.2.6 Port Isolation.........................................................................................................21
4.3 VLAN............................................................................................................. 22
4.3.1 VLAN setting.........................................................................................................23
4.3.2 Trunk-port setting.................................................................................................24
4.3.3 Hybrid-port setting............................................................................................... 25
4.4 Fault/Safety.................................................................................................. 26
4.4.1 Anti Attack............................................................................................................. 27
4.4.1.1 DHCP...........................................................................................................27
4.4.1.2 DOS.............................................................................................................29
4.4.1.3 IP Source Guard.................................................................................... 30
4.4.1.4 IP/Mac/Port............................................................................................ 31
4.4.2 Channel Detection............................................................................................... 32
4.4.2.1 Ping...........................................................................................................32
4.4.2.2 Tracert.................................................................................................... 33
4.4.2.3 Cable test.............................................................................................. 34
4.4.3 ACL.........................................................................................................................35
4.5 PoE................................................................................................................ 36
4.5.1 PoE config.............................................................................................................37

PS5026G-2GS-24PoE User Manual
2
4.5.1.1 management.............................................................................................. 37
4.5.1.2 Temperature config.............................................................................. 38
4.5.2 PoE port Config....................................................................................................39
4.6 MSTP.............................................................................................................40
4.6.1 MSTP Region....................................................................................................... 40
4.6.2 MSTP Bridge........................................................................................................ 41
4.7 DHCP Relay................................................................................................. 44
4.7.1 DHCP Relay......................................................................................................... 44
4.7.2 Option82................................................................................................................45
4.8 QOS...............................................................................................................46
4.8.1 Remark.................................................................................................................. 46
4.8.2 Queue Config....................................................................................................... 48
4.8.3 Mapping the Queue.............................................................................................49
4.8.3.1 Service class queue mapping............................................................ 49
4.8.3.2 Differential service class mapping.............................................. 50
4.8.3.3 Port to service class mapping........................................................ 51
4.9 Address Table...............................................................................................52
4.9.1 Mac add and delete.............................................................................................53
4.9.2 Mac study and Aging...........................................................................................54
4.9.3 Mac address filtering........................................................................................... 55
4.10 SNMP..........................................................................................................56
4.10.1 SNMP Config......................................................................................................56
4.10.1.1 SNMP Config.......................................................................................... 56
4.10.1.2 Community Config................................................................................ 57
4.10.1.3 Group Config........................................................................................ 57
4.10.1.4 User config.......................................................................................... 58
4.10.1.5 Trap.........................................................................................................60
4.10.1.6 View config.......................................................................................... 61
4.10.2 Rmon Config...................................................................................................... 62
4.10.2.1 Statistics Group................................................................................ 62
4.10.2.2 History Group...................................................................................... 63
4.10.2.3 Alarm Group.......................................................................................... 64
4.10.2.4 Event Group.......................................................................................... 65
4.11 System........................................................................................................ 66
4.11.1 System Config.................................................................................................... 67
4.11.1.1 System settings.................................................................................. 67
4.11.1.2 System restart.................................................................................... 69
4.11.1.3 Password................................................................................................ 70
4.11.1.4 SSH login.............................................................................................. 71
4.11.1.5 Telnet login........................................................................................ 71
4.11.1.6 System log............................................................................................ 72
4.11.2 System Upgrade................................................................................................ 73
4.11.3 Config Management..........................................................................................74

PS5026G-2GS-24PoE User Manual
3
4.11.3.1 Current configuration...................................................................... 74
4.11.3.2 Configuration backup........................................................................ 76
4.11.3.3 Restore factory configuration...................................................... 76
4.11.4 Config Save........................................................................................................ 77
4.11.5 Administrator Privileges.................................................................................... 78
4.11.6 Info Collect.......................................................................................................... 79
Appendix: Technical Specifications.................................................................. 80

PS5026G-2GS-24PoE User Manual
4
Chapter 1 Product Introduction
Congratulations on your purchasing of the Web Smart Ethernet Switch. Before you install
and use this product, please read this manual carefully for full exploiting the functions of
this product.
1.1 Product Overview
This is a new generation designed for high security and high performance network the
second layer Switch. Provides twenty-four 10/100/1000Mbps self-adaption RJ-45 port,
and two 100/1000Mbps SFP optical ports, all ports support wire-speed forwarding, can
provide you with larger network flexibility. Support VLAN ACL based on port, easily
implement network monitoring, traffic regulation, priority tag and traffic control. Support
traditional STP/RSTP/MSTP 2 link protection technology; greatly improve the ability of
fault tolerance, redundancy backup to ensure the stable operation of the network. Support
ACL control based on the time, easy control the access time accurately. Support 802.1x
authentication based on the port and MAC, easily set user access. Perfect QOS strategy
and plenty of VLAN function, easy to maintenance and management, meet the networking
and access requirements of small and medium-sized enterprises, intelligent village, hotel,
office network and campus network.
This Switch 24 ports support POE power supply function, support IEEE802.3at standard,
802.3af downward compatibility, power supply equipment for Ethernet, can automatically
detect identification standard of electrical equipment, and through the cable for the power
supply.
1.2 Features
Comply with IEEE 802.3i, IEEE 802.3u, IEEE802.3x, IEEE802.3ab, IEEE802.1q,
IEEE802.1p standards
Supports IEEE802.3af, IEEE802.3at standards
Supports PoE power up to 30W for each PoE port, all power up to 380W
Supports manage the POE port, support POE port power on/off and port output
power restriction
Support Web interface management
24 x 10/100/1000Mbps Auto MDI/MDI-X Ethernet port,Support ports Auto MDI/MDIX
8K entry MAC address table of the Switch with auto-learning and auto-aging
Supports IEEE802.3x flow control for Full-duplex Mode and backpressure for
Half-duplex Mode
supports QoS (quality of service), port mirror, Link aggregation protocol
Support packet length 9216Bytes jumbo frame packet forwarding at wire speed
LED indicators for monitoring PSE, Link / Activity/Speed

PS5026G-2GS-24PoE User Manual
5
1.3 External Component Description
1.3.1 Front Panel
The front panel of the Switch consists of 24 x 10/100/1000Mbps RJ-45 ports, 2 x
1000Mbps SFP ports, 1 x CONSOLE port, 1 x RESET button and a series of LED
indicators as shown as below.
10/100/1000Mbps RJ-45 ports (1~24):
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Each has a corresponding 10/100/1000Mbps LED.
SFP ports (SFP1, SFP2):
Designed to install the SFP module and connect to the device with a bandwidth of
1000Mbps. Each has a corresponding 1000Mbps LED.
CONSOLE port (CONSOLE):
Designed to connect with the serial port of a computer or terminal for monitoring and
configuring the Switch.
RESET button (RESET):
Keep the device powered on and press down the button for about 5 seconds. The system
restores the factory default settings.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential
problem with the Switch, connection or attached devices.
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.
LED
COLOR
STATUS
STATUS DESCRIPTION
PWR
Red
On
Power On
Off
Power Off
LINK/ACT
Orange
On
A device is connected to the port

PS5026G-2GS-24PoE User Manual
6
/SPEED
(1~24)
(10/100Mbps)
Off
A device is disconnected to the port
Green
(1000Mbps)
Flashing
Sending or receiving data
LINK/ACT
/SPEED
(SFP1,2)
Green
On
A device is connected to the port
Off
A device is disconnected to the port
Flashing
Sending or receiving data
PoE
(1~24)
Yellow
On
A Powered Device is connected to the
port, which supply power successfully.
Off
No Powered Device connected to the
port, or no power is supplied according to
the power limits of the port.
Flashing
The PoE power circuit may be in short or
the power current may be overloaded.
1.3.2 Rear Panel
The rear panel of the Switch contains AC power connector and one marker shown as
below.
AC Power Connector:
Power is supplied through an external AC power adapter. It
supports AC 100~240V,
50/60Hz.
Grounding Terminal:
The Switch already comes with Lightning Protection Mechanism. You can also ground
the Switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.
1.4 Environment
Operating Temperature: 0℃~45℃
Storage Temperature: -40℃~70℃
Operating Humidity: 10%~90% non-condensing
Storage humidity: 5%~90% non-condensing

PS5026G-2GS-24PoE User Manual
7
1.5 Package Contents
Before installing the Switch, make sure that the following the "packing list" listed OK. If any
part is lost and damaged, please contact your local agent immediately. In addition, make
sure that you have the tools install switches and cables by your hands.
One PoE Managed Ethernet Switch
Four rubber feet, two mounting ears and eights screws
One AC power cord
One User Manual

PS5026G-2GS-24PoE User Manual
8
Chapter 2 Installing and Connecting the Switch
This part describes how to install your Web Smart Ethernet Switch and make connections
to it. Please read the following topics and perform the procedures in the order being
presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.
Put the Switch on stable place or desktop in case of falling damage.
Make sure the Switch works in the proper AC input range and matches the voltage
labeled on the Switch.
To keep the Switch free from lightning, do not open the Switch’s shell even in power
failure.
Make sure that there is proper heat dissipation from and adequate ventilation around
the Switch.
Make sure the cabinet to enough back up the weight of the Switch and its
accessories.
2.1.1 Desktop Installation
Sometimes users are not equipped with the 19-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.
Figure 4 - Desktop Installation

PS5026G-2GS-24PoE User Manual
9
2.1.2 Rack-mountable Installation in 19-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
a. attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
Figure 5 - Bracket Installation
b. use the screws provided with the equipment rack to mount the Switch on the rack and
tighten it.
Figure 6 - Rack Installation
2.1.3 Power on the Switch
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or
multifunctional computer professional receptacle. Please make sure to connect the metal
ground connector to the grounding source on the outlet.
AC Power Cord Connection:

PS5026G-2GS-24PoE User Manual
10
Connect the AC power connector in the back panel of the Switch to external receptacle
with the included power cord, and check the power indicator is ON or not. When it is ON, it
indicates the power connection is OK.
2.2 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please
connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be
connected to any RJ-45 port of the Switch, the distance between Switch and computer is
around 100 meters. Once the connection is OK and the devices are power on normally,
the LINK/ACT/Speed status indicator lights corresponding ports of the Switch.

PS5026G-2GS-24PoE User Manual
11
Chapter 3 How to Login the Switch
3.1 How to Login the Switch
As the Switch provides Web-based management login, you can configure your computer’s
IP address manually to log on to the Switch. The default settings of the Switch are shown
below.
Parameter
Default Value
Default IP address
192.168.2.1
Default Username
admin
Default Password
admin
You can log on to the configuration window of the Switch through following steps:
1. Connect the Switch with the computer NIC interface.
2. Power on the Switch.
3. Check whether the IP address of the computer is within this network segment:
192.168.2.xxx (“xxx” ranges 2~254), for example, 192.168.2.100.
4. Open the browser, and enter http://192.168.2.1 and then press “Enter”. The Switch
login window appears, the following picture:
5. Enter the user name and password (factory default user name admin, password for
admin) and can choose the English interface, and then click "login", you can log in to
the following switch configuration window.

PS5026G-2GS-24PoE User Manual
12

PS5026G-2GS-24PoE User Manual
13
Chapter 4 Switch Configuration
This Switch Managed switch software provides rich layer 2 functionality for switches in
your networks. This chapter describes how to use Web-based management
interface(Web UI) to this switch configure managed switch software features.
In the Web UI, the left column shows the configuration menu. Above you can see the
information for switch system, such as memory. The middle shows the switch’s current
link status. Green squares indicate the port link is up, while gray squares indicate the port
link is down. The rest of the screen area displays the configuration settings.
4.1 Quickly Set
In the navigation bar to select "Quickly Set", can create a VLAN in this module, add the
port in the VLAN, set the basic information and modify the switch login password as
shown.

PS5026G-2GS-24PoE User Manual
14
【Parameter Description】
Parameter
Description
VLAN ID
VLAN number, 26GE default VLAN 1
VLAN name
VLAN mark
Manage IP
Manage the IP address of the VLAN
【Instructions】
Native VLAN: As a Trunk, the port will belong to a Native VLAN. The so-called Native
VLAN, is refers to UNTAG send or receive a message on the interface, is considered
belongs to the VLAN. Obviously, the interface of the default VLAN ID (PVID) in the IEEE
802.1 Q VLAN ID is the Native VLAN. At the same time, send belong to Native VLAN
frame on the Trunk, must adopt UNTAG way.
Allowed VLAN list: A Trunk can transport the equipment support by default all the VLAN
traffic (1-4094). But, also can by setting the permission VLAN Trunk at the port of the list to
limit the flow of some VLAN can't through the Trunk.
【Configuration Example】
VLAN setting: Such as create VLAN 2, Sets the port 8 to Trunk, Native VLAN 2.

PS5026G-2GS-24PoE User Manual
15
Click "next step" button, into other settings, such as: Manage IP address set as
192.168.2.11, device name set as Switch-123, Default gateway set as 192.168.2.22, DNS
server set as 172.16.1.241.
Use 192.168.2.11 to log in, set a new password for 1234.

PS5026G-2GS-24PoE User Manual
16
4.2 PORT
In the navigation bar to select "PORT", You may conduct Basic Config,Port
Aggregation,Port Mirroring,Port Limit,Storm Control and Port Isolation.
4.2.1 Basic Config
In the navigation bar to select "Port>Basic Config", for panel port to port described, port
speed, port status, working mode, flow control, cross line order configuration as shown.
【Parameter Descriptionion】
Parameter
Description
Port
Select the current configuration port number
Port status
Open or close ports
Flow control
Open or close the port flow control function

PS5026G-2GS-24PoE User Manual
17
Port speed
Can choose the following kinds:
Self negotiated
10M
100M
1000M
Working mode
Can choose the following kinds:
Self negotiated
Half duplex
Duplex
Port described
The port is described
Cross line sequence
Whether open intersection line sequence
【Instructions】
Open flow control should be negotiated will close, negotiated close is to set port speed
rate and working mode; Set the port rate more than actual rate of port, the port will be up.
【Configuration Example】
Such as: The port is set to 10M, Duplex,cross line sequence set to Auto, open flow control
and port state.
4.2.2 Port Aggregation
In the navigation bar to select "Port>Port Aggregation", in order to expand the port
bandwidth or achieve the bandwidth of the redundancy backup as shown.

PS5026G-2GS-24PoE User Manual
18
【Instructions】
The monitor port in the port image can not be added!
【Configuration Example】
Such as: Set the port 9, 10, for aggregation port 1, lets this aggregation port 1 connected
to other switch aggregation port 1 to build switch links.
4.2.3 Port Mirroring
In the navigation bar to select "Port>Port Mirroring", open port mirror feature, all packets
on the source port are copied and forwarded to the destination port, destination port is
usually connected to a packet analyzer to analyze the source port, multiple ports can be
mirrored to a destination port as shown.

PS5026G-2GS-24PoE User Manual
19
【Parameter Description】
Parameter
Description
Mirror group
Range: 1-4
Source port
To monitor the port in and out of flow
Destination port
Set destination port, All packets on the source port are copied
and forwarded to the destination port
【Instructions】
The port of the aggregate port can not be used as a destination port and the source port,
destination port and source port can not be the same.
【Configuration Example】
Such as: Set a mirror group for port 10 regulatory port 4, 6, 8 on and out flow
conditions.