3One data IPS7110-2GC-4POE Series User manual

IPS7110
（
&IPS716
）
-2GC-4POE series
Managed Industrial PoE switches
CLI user manual
Version 2.0.0, Mar. 2017
www.3onedata.com

CLI user manual
1www.3onedata.com
IPS7110（&IPS716）-2GC-4POE series user manual
Statement
Copyright Notice
Information in this document is reserved by Shenzhen 3onedata Technology
Co., Ltd. Reproduction and extract without permission is prohibited.
Models covered by this manual:
IPS716-2GC-4POE
IPS7110-2GC-4POE series
Trademarks Notice
and is registered trademarks of Shenzhen
3onedata Technology Co.,Ltd. All other trademarks or registered marks in this
manual belong to their respective manufacturers.
Agreement
As the product version upgrades or other reasons, this document is subject to
change without notice. Unless other agreement, this document only as a
guide to use. All statement, information and suggestion in this document,
without warranty of any kind, either expressed or implied.
Revision History
Version No. Date Reason
V1.0.0 2016-01-28 Creating Documents
V2.0.0 2017-03-17 Update
Notes
In reading this manual, please pay attention to the following symbols,
Information necessary to explain

CLI user manual
2www.3onedata.com
Special attention

CLI user manual
3www.3onedata.com
Content
Chapter 1 Login Ethernet Switch ..................................................................................................................................... 1
1.1 Configuration through console port ...................................................................................................................... 1
1.2 Configuration through Telnet ................................................................................................................................. 4
1.3 Agreement................................................................................................................................................................ 5
1.4 Command line port.................................................................................................................................................. 6
1.4.1 View of Command Lines................................................................................................................................. 6
1.4.2 Command lines Online help ........................................................................................................................... 8
1.4.3 Frequent Incorrect Information of Command Lines .................................................................................... 9
1.4.4 History command ........................................................................................................................................... 10
1.4.5 General Command ........................................................................................................................................ 10
Chapter 2 Device system based information configuration ....................................................................................... 11
2.1 Enter into the view of device information ........................................................................................................... 11
2.2 Display device information ................................................................................................................................... 11
2.3 Configuration information ..................................................................................................................................... 12
2.4 Delete device information .................................................................................................................................... 12
Chapter 3 Port Configuration.......................................................................................................................................... 14
3.1 Port information ..................................................................................................................................................... 14
3.2 Display port configuration information................................................................................................................ 14
3.3 Port configuration .................................................................................................................................................. 14
3.4 To enable or disable the port ............................................................................................................................... 15
3.5 Configure the port speed and duplex mode ...................................................................................................... 15
3.6 Configure the port flow control ............................................................................................................................ 15
Chapter 4 Bandwidth Management............................................................................................................................... 16
4.1 Enter rate management view............................................................................................................................... 16
4.2 Egress bandwidth configuration.......................................................................................................................... 16
4.3 Ingress bandwidth configuration ......................................................................................................................... 17
4.4 Configuration of Type of ingress limited packets .............................................................................................. 17
4.5 Displays the bandwidth configuration information ............................................................................................ 17
Chapter 5 IGMP ............................................................................................................................................................... 19
5.1 The contents of IGMP configuration ................................................................................................................... 19
5.2 IGMP snooping mode enable .............................................................................................................................. 19
5.3 IGMP query mode enable .................................................................................................................................... 19
5.4 Set IGMP query time............................................................................................................................................. 19
5.5 Check the MAC address table............................................................................................................................. 20
Chapter 6 VLAN ............................................................................................................................................................... 21
6.1 Introduction to VLAN............................................................................................................................................. 21
6.2 The contents of VLAN configuration................................................................................................................... 21

CLI user manual
4www.3onedata.com
6.3 Vlan information view............................................................................................................................................ 21
6.4 Enter the port configuration view based on Vlan .............................................................................................. 22
6.5 Enter configuration view based on 802.1QVlan ............................................................................................... 23
Chapter 7 Static Multicast filtering view ........................................................................................................................ 24
7.1 Enter the multicast filtering view ......................................................................................................................... 24
7.2 Add /Delete static multicast address .................................................................................................................. 24
7.3 Configuration of showing static multicast address ........................................................................................... 24
Chapter 8 QoS.................................................................................................................................................................. 25
8.1 Enter the multicast filtering view ......................................................................................................................... 25
8.2 Enable Dscp / Cos ................................................................................................................................................ 25
8.3 QoS queue configuration ..................................................................................................................................... 25
8.4 The value of Dscp/Tos mapping ......................................................................................................................... 26
8.5 The default port priority allocation....................................................................................................................... 26
8.6 Qos configuration information ............................................................................................................................. 26
Chapter 9 Ring configuration.......................................................................................................................................... 28
9.1 Enter the ring network configuration view.......................................................................................................... 28
9.2 Ring network state information view................................................................................................................... 28
9.3 To enable or disable the ring ............................................................................................................................... 28
9.4 The Ring3 configuration ....................................................................................................................................... 28
9.5 The RSTP configuration....................................................................................................................................... 29
Chapter 10 Trunk configuration ..................................................................................................................................... 32
10.1 Enter the port Trunk view................................................................................................................................... 32
10.2 Port trunk configuration / delete........................................................................................................................ 32
10.3 Display port trunk configuration information.................................................................................................... 32
Chapter 11 The SNMP configuration ......................................................................................................................... 33
11.1 Configure the view into the SNMP.................................................................................................................... 33
11.2 Enable the SNMP information ........................................................................................................................... 33
11.3 The SNMP configuration view ........................................................................................................................... 33
Chapter 12 Alarm configuration ..................................................................................................................................... 35
12.1 Enter the alarm information view ...................................................................................................................... 35
12.2 Alarm configuration / delete............................................................................................................................... 35
12.3 Display the alarm information............................................................................................................................ 35
Chapter 13 Port Statistics ............................................................................................................................................... 37
13.1 Enter the port statistical configuration view..................................................................................................... 37
13.2 Port Statistics configuration view ...................................................................................................................... 37
Chapter 14 Port mirroring ............................................................................................................................................... 38
14.1 Enter the port mirroring view ............................................................................................................................. 38
14.2 Port mirroring configuration / delete ................................................................................................................. 38

CLI user manual
5www.3onedata.com
14.3 Display port mirroring information..................................................................................................................... 38
Chapter 15 System management.................................................................................................................................. 40
15.1 Enter the System management configuration view ....................................................................................... 40
15.2 System timeout.................................................................................................................................................... 40
15.3 IP address and default gateway setting........................................................................................................... 40
15.4 User name, password settings.......................................................................................................................... 41
15.5 Display device IP, subnet mask, default gateway .......................................................................................... 41
15.6 Restore factory settings ..................................................................................................................................... 42
15.7 The address of the DNS server settings.......................................................................................................... 42
15.8 Obtain an IP address automatically set ........................................................................................................... 42
Chapter 16 PoE Setting .................................................................................................................................................. 43
16.1 Enter PoE settings view ..................................................................................................................................... 43
16.2 Disable or enable port PoE function................................................................................................................. 43
16.3 Configure PoE port maximum power, priority and POE total power ........................................................... 43
16.4 View port POE status information..................................................................................................................... 44
Chapter 17 LLDP Setting ................................................................................................................................................ 44
17.1 Enter LLDP settings view................................................................................................................................... 44
17.2 LLDP configuration and display ........................................................................................................................ 45

CLI user manual
1www.3onedata.com
Chapter 1 Login Ethernet Switch
1.1 Configuration through console port
1. Connection switches to configure terminal
As shown in Figure 1.1.1, the establishment of the local configuration environment, only the
computer serial cable and connected to the Console port of the Ethernet switch.
(Figure 1.1.1)
This cable is used for connecting the switch Console port and the external monitoring
terminal equipment. One end is RJ45 eight core plug, the other end is the 9 hole plug (DB9).
Console RJ45 the switch socket head, the cable inner connecting line diagram as shown
below.
(Figure 1.1.2)
2. Configure terminal parameters
1) Turn the computer, on the Windows interface, click "Start/All
Programs/Accessories/communication", run a terminal emulation program to create a new
connection. The RS-232 port is connected to the computer. To take Hyper Terminal in
Windows XP for example, as shown in Figure 1.1.3, type in a new name of the connection in
a text box named "name", then click "OK" button.

CLI user manual
2www.3onedata.com
(Figure 1.1.3)
2) Choose connecting serial port. Choose connecting serial port under “Connect using”（pay
attention to the chosen serial port is consistent with the port connected with the configuration
cable）,Click “OK”. As shown in Figure 1.1.4.
(Figure 1.1.4)
3) Set serial port parameters. As shown in Figure 1.1.5, set the “Bits per second” in the
“Properties” of serial port is 115200bit/s, “Data bits” is 8, “parity” is None, “Stop Bits” is 1,
“Flow Control” is None. Click “OK” button to enter to “Hyper Terminal” Window.

CLI user manual
3www.3onedata.com
(Figure 1.1.5)
4) Hyper terminal attribute. In the Hyper Terminal window select [document / property /
setting] into the attributes settings window. Select the terminal simulation of type VT100 or
automatic detection, click < OK > button to return to the hyper terminal window.
(Figure 1.1.6)

CLI user manual
4www.3onedata.com
5) For the switch power, power after the hyper terminal display Ethernet switch self-test
information, after the prompt the user to type the carriage return, until the emergence of
<user name> command prompt, this time to enter the correct username and password, enter
the switch system mode can be configured, the specific configuration commands refer to the
later chapters of the contents of the book in.
As the network pipeline connection than COM1, in step two must choose the corresponding COM port. Step three
"bits per second" must choose 115200, otherwise cannot be displayed.
1.2 Configuration through Telnet
Terminal device use telnet connect to the switch through PC, the requirements are as
follows:
1. The IP address of the switch can get it by search or modify (Use IP command under the
system management view);
2. If PC and the switch in the same local area network, the IP address must in a same
network segment, otherwise, PC and the switch must cross-router.
If satisfied these two requirements, can use telnet access to the switch, and then configure
the switch.
1）Establish configuration environment, just connect PC’s Ethernet port connect to the
switch’s Ethernet port through Local area network.
(Figure 1.2.1)
2）Run the Telnet program on the PC, need to input“Telnet+ Space+ switch’s IP address”
for checking, Figure 1.2.2 as follows:
(Figure 1.2.2)

CLI user manual
5www.3onedata.com
3）Hit “Enter”, checkout successful and till PC show“Please input hostname and password”,
ask user to input user name and password, default is admin, figure 1.2.3 as follows:
(Figure 1.2.3)
4）Use command to configure the switch and check the running statues, if need help,
please input“?” at any time. Specific configuration command, please
reference“IPS7110-2GC-4POE series CLI user manual”.
1.3 Agreement
1. Command line format agreement table 1.3.1 as follow
Table 1.3.1
Format Description
Bold Key words of the command show by bold type.
italic Parameter of the command show italic type.
[ ] It shows part in “[]”is optical when command configuration is need.
{ x | y | ... } It shows to pick up one from two or more items.
[ x | y | ... ] It shows to pick up one or no one from two or more items.
2. Format agreement of figure interface Table 1.3.2 as follows:
Table 1.3.2
Format Description
< > “< >” shows press name, like ”click<OK>”
[ ]
“[ ]” shows windows name, menu name and data list. like “eject [create
user]window”
/ Multilevel is separated by “/”. Like [file/create/folder] means[create] a [folder] under
the menu of [file]

CLI user manual
6www.3onedata.com
1.4 Command line port
The switch provide command lines port and its configuration for user’s easy
configuration and management. Command lines port includes the following features:
1. Local configuration through Console port;
2. Supports history command saving which means it can save 10 pieces. History
commands can be selected by up and down key.
3. User can type in “help” or ”?” to get some help;
4. Supports intelligent complement with Tab when commands input;
5. Command interpreter take the method of partial matching. User can type in
conflict-free key words, such as config command, only need to type in conf.
1.4.1 View of Command Lines
The switch view of command lines aim at configuration of different functions. First of all, the
switch establish connection, then confirmation of user name and password finished, after
enter the correct user name and password, enter “help or ?” in “switch”, enter into system
view, Under the view of system, corresponding view appears after typing indifferent
command, figure 1.4.1 as follows:
(Figure 1.4.1)

CLI user manual
7www.3onedata.com
Table 1.4.1 system view command list
View
Function
Prompt
Enter
Quit
System -
Switch# Quit and
return to
user
login
Device
Information
Show or modify device
information, like
software version, IP
address, etc.
Device_information#
Information
Exit and
return to
the view
of
system
Port Setting
Show or modify port
information, like duplex
mode, port enable.
Port_config# Port
Bandwidth
Management
Show or modify
bandwidth information,
like ingress and egress
bandwidth
configuration.
Bandwidth# Bandwidth
IGMP
Igmp snooping
IGMP#
IGMP
LLDP
LLDP setting LLDP#
LLDP
VLAN
Show or modify
information of VLAN,
like add Vlan, pvid, port
type, etc.
Vlan_config# Vlan
Static Multicast
Filtering
Show or modify static
multicast address, like
add static multicast
address.
Multicast_filters#
Multicast
QoS
Show or modify value
of Qos, Tos, like Qos,
Tos etc.
QoS_config# QoS
Ring
Show or modify Ring
information, like Ring
id,Ring port, etc.
Ring# Ring
Trunking
setting
Show or modify port
trunking information,
like trunking
information.
Port_Trunk#
Trunk

CLI user manual
8www.3onedata.com
SNMP
Snmp setting SNMP#
SNMP
Alarm Setting
Show or modify alarm
informa
tion, like power
alarm, port alarm, etc.
Alarm_config#
Alarm
Port Mirror
Show or modify port
mirroring information
Port_mirror# Mirror
System
Management
Show or modify
configuration
information, like IP
address,
subnet mask,
default gate
way and
password, etc.
System_manage# Manage
Time Enter time zone setting
menu
Time# TIme
1.4.2 Command lines Online help
Command lines port provides the following online help:
Total help;
Partial help;
1. Total help
1）Type in <?> to get all commands and their description.
Example:
Switch# ?
List --List commands of current menu
Poe <dir> --Enter POE setting menu
Help --Help commands of current menu
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch
Port <dir> --Enter port setting menu
Bandwidth <dir> --Enter bandwidth management menu
Igmp <dir> --Enter igmp snooping menu
Lldp <dir> --Enter lldp setting menu
Vlan <dir> --Enter vlan menu
QoS <dir> --Enter QoS menu
Ring <dir> --Enter Ring menu
Trunk <dir> --Enter Trunking setting menu

CLI user manual
9www.3onedata.com
Snmp <dir> --Enter snmp setting menu
Alarm <dir> --Enter alarm setting menu
Statistics <dir> --Enter statistics menu
Mirror <dir> --Enter port mirror menu
Manage <dir> --Enter system manage menu
Multicast <dir> --Enter static multicast filters menu
Information <dir> --Enter device information menu
Time <dir> --Enter time zone setting menu
2）Type in a command and “?”, between there is a space, if key word is in this location,
then type in all keywords and descriptions.
Example:
Switch (information)# show?
Show mac --Show device MAC Address
Show version --Show device version
Show others --Show device type, name, etc
2. Partial help
1）Type in a character string with <?>. It can show all commands beginning with this
character string.
Example:
Switch# M?
Mirror <dir> --Enter port mirror menu
Manage <dir> --Enter system manage menu
Multicast <dir> --Enter static multicast filters menu
2）Type in former letters of some key word of the command, press<Tab> key. If the letters
are unique, it can show the completed key word.
Example:
Switch# inf+<Tab>
Switch# information
1.4.3 Frequent Incorrect Information of Command Lines
All commands typed by users, if it is certificated by grammar, it can run correctly, or
users will be sent incorrect information. Frequent incorrect information is in table 1.4.3 as
below:
Table 1.4.3 Frequent incorrect information
English incorrect information
Reason

CLI user manual
10 www.3onedata.com
English incorrect information
Reason
Invalid Command
Command cannot be found.
Key word cannot be found.
The type of parameter is wrong.
The parameter is beyond the border.
Incomplete Command Command is not completed.
Too many parameters Parameter is too much.
1.4.4 History command
Command lines port can provides the function similar to Dos key. It automatic save command lines
that users types in, and users can use these history commands. Detailed operating please check table
1.4.4 as follows:
Table 1.4.4 access history command
Operating
Key
Result
Visit previous history
command Up <↑> If it exists earlier command, it is taken out.
Visit next history command Down <↓> If it exists later command, it is taken out.
1.4.5 General Command
Regular command is the most frequently used commands, in order to facilitate the operation,
the list and help, quit, exit and reboot command arrangements in all modes.
Table 1.4.5 general command
Operating Key Result
List commands of current menu List
In any mode can be executed
Help commands of current
menu Help
Quit from CLI Quit
Exit from current menu Exit
Reboot switch Reboot

CLI user manual
11 www.3onedata.com
Chapter 2 Device system based information configuration
Device information includes Device Type, Hardware Version, Device Name, Software Version, Device
Description, Device SN and Contact Way. Among them, Hardware Version and Software Version can be
only read, not modified.
2.1 Enter into the view of device information
Please check the view as figure 2.1.1
Table 2.1.1
Operating Command Description
Enter into the view of device information Information Run in the view of system
2.2 Display device information
Please check the device information command as table 2.2.1
Table 2.2.1
Operating
Command
Description
Show system version show version Carry out under the view of device information
Show MAC address of device show mac Carry out under the view of device information
Show Device Type, Name, etc. show others Carry out under the view of device information
Configure device model, name
etc config Carry out under the view of device information
Delete device model, name etc
clean
Carry out under the view of device information
Example: Enter into device information view, enter the bold type command as follows and enter return
key
Switch# information
Switch(information)# show others
Device type MangedSwitch
Device name IndustrialSwitch
Description 10PORT
Serial number
Contact way

CLI user manual
12 www.3onedata.com
2.3 Configuration information
Please reference user configuration device information as table 2.3.1:
Table 2.3.1
Operating Command Description
Configure Device Type config –t type
Type: configurable type, the length is
between 1～16 characters
Configure Device Name config -n name
Name: configurable name, the length is
between1～16 characters
Configure Serial Number config -m number
Number: configurable number, the length is
between 1～28 characters
Configure Device Description config -p
description
Description: configurable description, the
length is between 1～16 characters
Configure Contact
information config -c contact Contact: Configure Contact way 1-28 bytes
Example: Configure device name as AB123, enter the bold type command as follows and enter return
key:
Switch(information)# config -n ABC123
[OK]
2.4 Delete device information
Please reference table 2.4.1
Table 2.4.1
Operating Command Description
Delete Device Type Clean –t Carry out
under the view of device
information
Delete Device Name Clean -n Carry out
under the view of device
information
Delete Serial Number Clean -m Carry out
under the view of device
information
Delete Device
Description Clean -p Carry out
under the view of device
information
Delete Contact
information Clean -c Carry out
under the view of device
information
Example: Delete device name, enter the bold type command as follows and enter return key:
Switch(information)# clean -n
[OK]
Example: Delete Serial Number, enter the bold type command as follows and enter return key:

CLI user manual
13 www.3onedata.com
Switch(information)# clean -m
[OK]
Example: Delete Contact information, enter the bold type command as follows and enter return key:
Switch(information)# clean -c
[OK]

CLI user manual
14 www.3onedata.com
Chapter 3 Port Configuration
Port information including link state (link or LOS), the port state (full or half), rate mode
(automatic negotiation, 10Mbps, 100Mbps), interface type (electric or optical), flow control,
port is enabled.
3.1 Port information
The Ethernet port characteristics of the switches support:
10/100Base-Tx Ethernet port can operate in half duplex, full duplex, auto negotiation mode.
Support MDI/MDIX adaptive, and able to negotiate with other network devices, automatic
selection of the most appropriate way of working and rate, which greatly simplifies the
configuration and management system; 100Base-FX port, rate of 100Mbps, working in full
duplex mode, flow control can be set.
Enter the port configuration view
Table 3.1.1 to enter the port configuration view:
Table 3.1.1
Operating Command Description
Enter the port configuration
view
port In view of the system under the
3.2 Display port configuration information
Table 3.2.1 shows the command port configuration information:
Table 3.2.1
Operating Command Description
Display port state information
Show state
<portlist> <portlist>:1,3,5-10 or all
Display port configuration
information Show config <portlist> <portlist>:1,3,5-10 or all
Example: display port state information 3, 4, 5
Switch(Port)# show state 3,4,5
Speed Port_status Link_status Interface_type
port 3 10M HALF LOS TX
port 4 10M HALF LOS TX
port 5 100M FULL Link TX
3.3 Port configuration
Port configuration including:
1 To enable or disable the port;
2 Configure the port speed and duplex mode;
3 The allocation of port flow control;
4 Remove the statistics information of port frame;