3One data IES2016-16T Series User manual

IES2016-16T Series
Unmanaged Industrial Ethernet
Switch Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Te l :
[phone]
Fax:
[phone]
【
Package checklist
】
Please check whether the package and accessories are intact
while using the switch for the first time.
1.
Industrial Ethernet switch
2.
Certification
3.
DIN-Rail mounting attachment
4.
Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview
】
This series of products are unmanaged DIN-Rail industrial
Ethernet switches. Models as follows:
Model I. IES2016-16T-2P48 (16 100M copper ports + 2
12~48VDC power supply)
Model II. IES2016-16T-P220 (16 100M copper ports + 1
100~240VAC power supply)
【
Panel design
】
Rear view, bottom view and top view
Model I
Model II
Front view
Model I Model II
1. Wall mounting hole
2. DIN-Rail mounting kit
3. Power supply input terminal block
4. DIP switch
5. Grounding screw
6. Running indicator RUN
7. Alarm indicator ALM(Reserved)
8. Power supply indicator P1/P2
9. Copper port connection indicator
10. 100M Ethernet copper port
【
Mounting Dimension
】
Unit: mm

Attention before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:
Check whether the DIN-Rail mounting kit thatStep 1
comes with the device is installed firmly.
Insert the bottom of DIN-Rail mounting kit (one sideStep 2
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed onStep 3
DIN-Rail, and then mounting ends.
【Disassembling DIN-Rail】
Power off the device.Step 1
After lift the device upward slightly, first shift out theStep 2
top of DIN-Rail mounting kit, and then shift out the
bottom of DIN-Rail, disassembling ends.
Attention before powering on:
Power ON operation: first connect power line to the
connection terminal of device power supply, and then
power on.
Power OFF operation: first unpin the power plug, and
then remove the power line, please note the operation
order above.
【Power Supply Connection】
DC power supply
This series of Model I provide 4-pin 5.08mm
pitch power input terminal blocks and two
independent DC power supply systems of
P1 and P2. The power supply supports
anti-reverse connection and 3A
over-current protection. Power supply range: 12~48VDC.
AC power supply
This series of model II support AC single
power supply scheme. They provide 4-pin
5.08mm pitch input terminal blocks with 2
power supply pins. It supports 2A
over-current protection. Input voltage of power supply:
220VAC (100~240VAC).
【DIP Switch Settings】
It provides 4-pin DIP switch for function settings,
among which “ON” is enable valid end.
The definitions of DIP switch are as follows:
DIP
Definition
Operation
1 Flow control Set the DIP switch to ON, then
the device will reboot and
enable the flow control
function.
2 Storm suppression Set the DIP switch to ON, then
the device will reboot and
enable the storm suppression
function.
3
Reserved
－
4
Reserved
－
【Checking LED Indicator】
The function of each LED is described in the table as below:
LED
Status
Description
P1/P2
(only for
DC
product)
ON Power supply is connected and
running normally
OFF Power supply is disconnected and
running abnormally.
RUN
ON
Device is running normally.
OFF Device is disconnected and running
abnormally.
Link/ACT
(1-16)
ON
Ethernet port connection is active.
Blinking
Data transmitted
OFF
Ethernet port connection is inactive.
【Specification】
Panel
100M copper port
10/100Base-T(X) self-adapting
RJ45 port, full/half duplex
self-adaption, support
MDI/MDI-X self-adaption
Indicator Power indicator, interface
indicator, running indicator
Exchange attributes

Backplane bandwidth
3.2G
MAC table size
8K
Power supply
Model I
Input voltage of power supply:
12~48VDC
Support dual power supply
redundant backup and
non-polarity connection
Model II Input voltage of power supply:
100~240VAC
Access terminal 4 pins 5.08mm pitch terminal
blocks
Consumption
Model II No-load: 0.7W@220VAC
Full-load: 2.6W@220VAC
Environmental Limits
Working temperature
-40~75
℃
Storage temperature
-40~85
℃
Working humidity
5%~95% (no condensation)
Protection grade
IP40 (metal shell)