3One data PS5010G-2GS-8PoE User manual

PS5010G-2GS-8PoE User Manual
PS5010G-2GS-8PoE
Managed Full Gigabit
Industrial Ethernet PoE Switch
User Manual
Version 1.0, 2017.8.29

PS5010G-2GS-8PoE User Manual
1
Table of Contents
Chapter 1 Product Introduction............................................................................ 4
1.1 Product Overview.......................................................................................... 4
1.2 Features.......................................................................................................... 4
1.3 External Component Description................................................................ 5
1.3.1 Front Panel..............................................................................................................5
1.3.2 Rear Panel.............................................................................................................. 6
1.4 Package Contents......................................................................................... 6
2.1 Installation.......................................................................................................8
2.1.1 Desktop Installation............................................................................................... 8
2.1.2 Rack-mountable Installation in 11-inch Cabinet............................................... 8
2.1.3 Power on the Switch..............................................................................................9
2.2 Connect Computer (NIC) to the Switch......................................................9
2.3 Switch connection to the PD........................................................................9
Chapter 3 How to Login the Switch....................................................................11
3.1 Switch to End Node.....................................................................................11
3.2 How to Login the Switch............................................................................. 11
Chapter 4 Switch Configuration..........................................................................14
4.1 Quickly setting..............................................................................................14
4.2 PORT.............................................................................................................17
4.2.1 Basic config...........................................................................................................17
4.2.2 Port aggregation.................................................................................................. 19
4.2.3 Port mirroring........................................................................................................20
4.2.4 Port rate-limit........................................................................................................ 21
4.2.5 Storm control........................................................................................................ 23
4.2.6 Port isolation.........................................................................................................24
4.3 VLAN............................................................................................................. 26
4.3.1 VLAN config..........................................................................................................26
4.3.2 Trunk-port setting.................................................................................................27
4.3.3 Hybrid-port setting............................................................................................... 29
4.4 Fault/Safety.................................................................................................. 31
4.4.1 Anti attack..............................................................................................................31
4.4.1.1 DHCP...............................................................................................................................31
4.4.1.2 DOS................................................................................................................................. 33
4.4.1.3 IP source guard.............................................................................................................. 34
4.4.1.4 IP/Mac/Port..................................................................................................................... 35
4.4.2 Channel detection................................................................................................36
4.4.2.1 Ping.................................................................................................................................. 36

PS5010G-2GS-8PoE User Manual
2
4.4.2.2 Tracert..............................................................................................................................37
4.4.2.3 Cable test........................................................................................................................ 38
4.4.3 ACL.........................................................................................................................38
4.5 POE............................................................................................................... 40
4.5.1 POE Config........................................................................................................... 41
4.5.1.1 Management...................................................................................................................41
4.5.1.2 Temperature distribution............................................................................................... 41
4.5.2 POE Port Config.................................................................................................. 42
4.5.3 POE Delay Config................................................................................................43
4.6 STP................................................................................................................44
4.6.1 MSTP region.........................................................................................................44
4.6.2 STP bridge............................................................................................................ 45
4.7 DHCP relay...................................................................................................48
4.7.1 DHCP relay........................................................................................................... 48
4.7.2 0ption82.................................................................................................................49
4.8 QoS................................................................................................................50
4.8.1 Remark.................................................................................................................. 50
4.8.2 Queue config........................................................................................................ 52
4.8.3 Mapping the queue..............................................................................................53
4.8.3.1 Service class queue mapping........................................................................ 53
4.8.3.2 Differential service class mapping...............................................................................54
4.8.3.3 Port to service class mapping......................................................................................55
4.9 Address table............................................................................................... 56
4.9.1 Mac add and delete.............................................................................................57
4.9.2 Mac study and laging.......................................................................................... 58
4.9.3 Mac address filtering........................................................................................... 60
4. 10 SNMP.........................................................................................................60
4.10.1 Snmp config........................................................................................................61
4.10.1.1 Snmp config..................................................................................................................61
4.10.1.2 Community config........................................................................................................61
4.10.1.3 View config................................................................................................................... 62
4.10.1.4 Group config................................................................................................................. 63
4.10.1.5 User config....................................................................................................................64
4.10.1.6 Trap................................................................................................................................66
4.10.2 Rmon config....................................................................................................... 67
4.10.2.1 Statistics group.............................................................................................................67
4.10.2.2 History group................................................................................................................ 68
4.10.2.3 Event group.................................................................................................................. 69
4.10.2.4 Alarm group.................................................................................................................. 70
4.11 SYSTEM..................................................................................................... 71
4.11.1 System config..................................................................................................... 72
4.11.1.1 System settings............................................................................................................72
4.11.1.2 System restart.............................................................................................................. 74
4.11.1.3 Password change........................................................................................................ 75

PS5010G-2GS-8PoE User Manual
3
4.11.1.4 SSH login...................................................................................................................... 76
4.10.1.5 Telnet login....................................................................................................................77
4.11.1.6 System log.................................................................................................................... 77
4.11.2 System upgrade.................................................................................................79
4.11.3 Config management..........................................................................................80
4.11.3.1 Current configuration...................................................................................................80
4.11.3.2 Configuration backup.................................................................................................. 82
4.10.3.3 Restore factory configuration.....................................................................................83
4.11.4 Config save......................................................................................................... 84
4.11.5 Administrator privileges.....................................................................................84
4.11.6 Info collect........................................................................................................... 85
Appendix: Technical Specifications.................................................................. 87

PS5010G-2GS-8PoE User Manual
4
Chapter 1 Product Introduction
Congratulations on your purchasing of the PoE Web Smart Ethernet Switch. Before you
install and use this product, please read this manual carefully for full exploiting the
functions of this product.
1.1 Product Overview
This is a new generation designed for high security and high performance network
the second layer switch. Provides eight 10/100/1000Mbps self-adaption RJ45 port, and
two 100/1000Mbps SFP optical ports, all ports support wire-speed forwarding, can provide
you with larger network flexibility. Support VLAN ACL based on port, easily implement
network monitoring, traffic regulation, priority tag and traffic control. Support traditional
STP/RSTP/MSTP 2 link protection technology; greatly improve the ability of fault
tolerance, redundancy backup to ensure the stable operation of the network. Support ACL
control based on the time, easy control the access time accurately. Support 802.1x
authentication based on the port and MAC, easily set user access. Perfect QOS strategy
and plenty of VLAN function, easy to maintenance and management, meet the networking
and access requirements of small and medium-sized enterprises, intelligent village, hotel,
office network and campus network.
The is 8 ports have POE power supply function, support IEEE802.3at standard,
802.3af downward compatibility, power supply equipment for Ethernet, can automatically
detect identification standard of electrical equipment, and through the cable for the power
supply.
1.2 Features
Comply with IEEE 802.3i, IEEE 802.3u, IEEE802.3x , IEEE802.3ab , IEEE802.1q ,
IEEE802.1p standards.
Supports IEEE802.3af、IEEE802.3at standards.
Supports PoE power up to 30W for each PoE port, all power up to 140W.
Supports manage the POE port, support POE power off open the port, and port
output power restriction.
Support Web interface management.
8 x 10/100/1000Mbps Auto MDI/MDI-X Ethernet port, Support ports Auto MDI/MDIX.
8K entry MAC address table of the switch with auto-learning and auto-aging.
Supports IEEE802.3x flow control for Full-duplex Mode and backpressure for
Half-duplex Mode.
supports QoS (quality of service), port mirror, Link aggregation protocol.
Support packet length 9216Bytes jumbo frame packet forwarding at wire speed.
Supports 4KV Surge Immunity for all UTP ports.
LED indicators for monitoring PSE, Link / Activity/Speed.

PS5010G-2GS-8PoE User Manual
5
1.3 External Component Description
1.3.1 Front Panel
The front panel of the Switch consists of 8 x 10/100/1000Mbps RJ-45 ports, 1x
CONSOLE port, 2 x SFP ports, 1 x RESET button and a series of LED indicators as
shown as below.
Figure 1 - Front Panel
10/100/1000Mbps RJ-45 ports (1~8):
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Each has a corresponding 10/100/1000Mbps LED.
CONSOLE port (CONSOLE):
Designed to connect with the serial port of a computer or terminal for monitoring and
configuring the Switch.
SFP ports (SFP1, SFP2):
Designed to install the SFP module and connect to the device with a bandwidth of
1000Mbps. Each has a corresponding 1000Mbps LED.
RESET button (RESET):
Keep the device powered on and push a paper clip into the hole.
Press down the button for 2 seconds to reboot the Switch, Press down the button for 5
seconds to restore the Switch to its original factory default settings.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential
problem with the Switch, connection or attached devices.
Figure 2 - LED Indicators
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.

PS5010G-2GS-8PoE User Manual
6
LED
COLOR
STATUS
STATUS DESCRIPTION
PWR
Green
On
Power On
Off
Power Off
LINK/ACT/
(1-8)
10/100M:
Orange
On
A device is connected to the port
Off
A device is disconnected to the port
1000M:
Green
Flashing
Sending or receiving data
PoE
Yellow
On
A Powered Device is connected to the port,
which supply power successfully
Off
No PD is connected to the corresponding
port, or no power is supplied according to
the power limits of the port
Flashing
The PoE power circuit may be in short or
the power current may be overloaded
LINK/ACT/
(9S-10S)
Green
On
A device is connected to the port
Off
A device is disconnected to the port
Flashing
Sending or receiving data
1.3.2 Rear Panel
The rear panel of the Switch contains AC power connector and one marker shown as
below.
Figure 3 - Rear Panel
AC Power Connector:
Power is supplied through an external AC power adapter. It s
upports AC 100~240V,
50/60Hz.
1.4 Package Contents
Before installing the Switch, make sure that the following the "packing list" listed OK. If any
part is lost and damaged, please contact your local agent immediately. In addition, make
sure that you have the tools install switches and cables by your hands.

PS5010G-2GS-8PoE User Manual
7
One PoE Web Smart Ethernet Switch.
Four rubber feet, two mounting ears and eights screws.
One AC power cord.

One User Manual.

PS5010G-2GS-8PoE User Manual
8
Chapter 2 Installing and Connecting the Switch
This part describes how to install your PoE Ethernet Switch and make connections to it.
Please read the following topics and perform the procedures in the order being presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.
Put the Switch on stable place or desktop in case of falling damage.
Make sure the Switch works in the proper AC input range and matches the voltage
labeled on the Switch.
To keep the Switch free from lightning, do not open the Switch’s shell even in power
failure.
Make sure that there is proper heat dissipation from and adequate ventilation around
the Switch.
Make sure the cabinet to enough back up the weight of the Switch and its
accessories.
2.1.1 Desktop Installation
Sometimes users are not equipped with the 11-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.
2.1.2 Rack-mountable Installation in 11-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 11-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
a. attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
Figure 4 - Bracket Installation

PS5010G-2GS-8PoE User Manual
9
b. use the screws provided with the equipment rack to mount the Switch on the rack and
tighten it.
Figure 5 - Rack Installation
2.1.3 Power on the Switch
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or
multifunctional computer professional receptacle. Please make sure to connect the metal
ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector in the back panel of the Switch to external receptacle
with the included power cord, and check the power indicator is ON or not. When it is ON, it
indicates the power connection is OK.
2.2 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please
connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be
connected to any RJ-45 port of the Switch, the distance between Switch and computer is
around 100 meters.Once the connection is OK and the devices are power on normally, the
LINK/ACT/Speed status indicator lights corresponding ports of the Switch.
2.3 Switch connection to the PD
1-8 ports of the Switch have PoE power supply function, the maximum output power up to

PS5010G-2GS-8PoE User Manual
10
30W each port, it can make PD devices, such as internet phone, network camera,
wireless access point work.You only need to connect the Switch PoE port directly
connected to the PD port by network cable.

PS5010G-2GS-8PoE User Manual
11
Chapter 3 How to Login the Switch
3.1 Switch to End Node
Use standard Cat.5/5e Ethernet cable (UTP/STP) to connect the Switch to end nodes as
described below. Switch ports will automatically adjust to the characteristics (MDI/MDI-X,
speed, duplex) of the device to which is connected.
Figure 6 - PC Connect
Please refer to the LED Indicators. The LINK/ACT/Speed LEDs for each port lights on
when the link is available.
3.2 How to Login the Switch
As the Switch provides Web-based management login, you can configure your computer’s
IP address manually to log on to the Switch. The default settings of the Switch are shown
below.
Parameter
Default Value
Default IP address
192.168.2.1
Default user name
admin
Default password
admin
You can log on to the configuration window of the Switch through following steps:
1. Connect the Switch with the computer NIC interface.
2. Power on the Switch.
3. Check whether the IP address of the computer is within this network segment:
192.168.2.xxx (“xxx” ranges 2~254), for example, 192.168.2.100.
4. Open the browser, and enter http://192.168.2.1 and then press “Enter”. The Switch
login window appears, as shown below.

PS5010G-2GS-8PoE User Manual
12
Figure 7- Login Windows
5. Switching language to english .Enter the Username and Password (The factory default
Username is admin and Password is admin), and then click “LOGIN” to log in to the
Switch configuration window as below.

PS5010G-2GS-8PoE User Manual
13

PS5010G-2GS-8PoE User Manual
14
Chapter 4 Switch Configuration
The Web Smart Ethernet Switch Managed switch software provides rich layer 2
functionality for switches in your networks. This chapter describes how to use Web-based
management interface(Web UI) to this switch configure managed switch software
features.
In the Web UI, the left column shows the configuration menu. Above you can see the
information for switch system, such as memory, software version.The middle shows the
switch’s current link status. Green squares indicate the port link is up, while black squares
indicate the port link is down. Below the switch panel, you can find a common toolbar to
provide useful functions for users. The rest of the screen area displays the configuration
settings.
4.1 Quickly setting
In the navigation bar to select “quickly setting”, can create a VLAN in this module, add
the port in the VLAN , set the basic information and modify the switch login password. the
following picture:

PS5010G-2GS-8PoE User Manual
15
【parameter description】
parameter
description
VLAN ID
VLAN number, 8GE default VLAN 1
VLAN name
VLAN mark
Manage IP
Manage the IP address of the VLAN
device name
Switch name
Manage VLAN
Switches management in use of the VLAN
【instructions】
Native VLAN: as a Trunk, the mouth will belong to a Native VLAN. The so-called Native
VLAN, is refers to UNTAG send or receive a message on the interface, is considered
belongs to the VLAN. Obviously, the interface of the default VLAN ID (PVID) in the IEEE
802.1 Q VLAN ID is the Native VLAN. At the same time, send belong to Native VLAN
frame on the Trunk, must adopt UNTAG way.
Allowed VLAN list: a Trunk can transport the equipment support by default all the VLAN
traffic (1-4094). But, also can by setting the permission VLAN Trunk at the mouth of the
list to limit the flow of some VLAN can't through the Trunk.
【Configuration example】
1）VLAN setting:such as create VLAN 2 , Sets the port 8 to Trunk , Native VLAN 2.

PS5010G-2GS-8PoE User Manual
16
2) click“next step” button, into other settings, such as:manage ip address set as
192.168.2.11, device name set as switch-123, default gateway with the dns server set as
172.16.1.241.

PS5010G-2GS-8PoE User Manual
17
Use 192.168.2.11 to log in, set a new password for 1234 .
4.2 PORT
In the navigation bar to select “PORT”, You may conduct basic config, port aggregation,
port mirroring , port limit and port isolation.
4.2.1 Basic config
In the navigation bar to select “PORT>basic config”, For panel port to port described ,
port speed, port status, working mode, flow control, cross line order configuration, the
following picture:

PS5010G-2GS-8PoE User Manual
18
【parameter description】
parameter
description
port
Select the current configuration port number
port status
Choose whether to close link port
flow control
Whether open flow control
port speed
Can choose the following kinds:
Aggregation
10 M
100 M
1000 M
working mode
Can choose the following kinds:
Self negotiated
10 M
100 M
1000 M
port described
The port is described
Cross line sequence
Whether open intersection line sequence
【instructions】
Open flow control should be negotiated will close, negotiated close is to set port speed
rate and working mode. Set the port rate more than actual rate of port, the port will be up.
【Configuration example】
Such as:The port is set to 10 M, half duplex, open flow control and cross line sequence

PS5010G-2GS-8PoE User Manual
19
and port state.
4.2.2 Port aggregation
In the navigation bar to select “PORT>port aggregation”, In order to expand the port
bandwidth or achieve the bandwidth of the redundancy backup, the following picture:
【parameter description】
parameter
description
Aggregation port
8 GE switch can be set up eight link trunk group, group_1 to
group_8
Member port
For each of the members of the group and add your own port,
and with members of other groups
【instructions】
Open the port of the ARP check function, the port of the important device ARP, the port of
the VLAN MAC function, and the monitor port in the port image can not be added!