3One data ES1026-2F User manual

ES1026-2F
Unmanaged Ethernet Switch
Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Song Bai Road, Nanshan
District, Shenzhen, 518108, China
Website:
www.3onedata.com
Tel:
[phone]
Fax:
[phone]
【Package Checklist】
Please check the integrity of package and accessories while
first using the switch.
1.
Industrial Ethernet switch X 1
2.
Terminal block
3.
Power line
4.
Certification
5.
Quick installation guide
6.
Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
This product is 26-port 100M rack-mounted unmanaged
Ethernet switches. Model is: ES1026 (24 100M copper ports +
2 100M fiber ports)
【Panel Design】
Front view
Rear view
Top view
Left view
Right view
1. Port indicator
2. Power supply input status indicator PWR
3. Device running status indicator RUN
4. Rack mounting lug
5. Power input terminal block
6. 100M fiber port
7. 100M copper port
【Mounting Dimension】
Unit: mm
Attention before mounting:
Don't place or install the device in moist area or near
water, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running,
please don't directly contact to avoid scalding.
【Installation of Rack-mounted Device】
Step 1 Select the device installation location to reserve

sufficient size.
Step 2 Adopt screws to install the mounting lugs in the
device position as figure below.
Step 3 Place the device in the rack, adopt 4 screws to
install the mounting lugs on the left and right side in
the rack.
Step 4 Check and confirm the product is firmly installed on
the rack, then mounting ends.
【Rack-mounting Device Disassembling】
Step 1 Power off the device.
Step 2 Unscrew the fixing screw of mounting lug on the
rack.
Step 3 Remove the device from the rack, disassembling
ends.
Attention before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
and then plug the power supply plug contact and power
on.
Power OFF operation: First unpin the power plug, and
then remove the wiring part of terminal block, please
pay attention to the operation order above.
【Power Supply Connection】
AC power supply
This series of devices provide 4-pin
7.62mm pitch terminal blocks. The pins of
terminal from the left to the right are L, FG,
FG, N. The power supply range: 100~240VAC/DC.
【Checking LED Indicator】
The device provides LED indicators to monitor the device
working status with a comprehensive and simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Status
Description
POWER
ON
Power supply is connected and
running normally
OFF
Power supply is disconnected or
running abnormally.
RUN
ON
The device is powering on or
abnormal
OFF
The device isn't powered on or is
abnormal
Blinking
Flash 1 time per second, the device
is running normally.
Link/Act
(1-26)
ON
Ethernet port connection is active.
Blinking
Ethernet port is in network active
status
OFF
Ethernet port connection is inactive
【Specification】
Panel
100M copper port
10/100Base-T(X), RJ45 port,
automatic flow control, half/full
duplex self-adaption,
MDI/MDI-X self-adaption
100M fiber port
100Base-FX, optional
SC/ST/FC interface
Indicator
Power supply indicator, run
indicator, interface indicator
Exchange Attributes
Backplane bandwidth
12.8G
Packet buffer size
2.5Mbit
MAC table size
8K
Power supply
Input power supply
100~240VAC/DC
Access terminal
4-pin 7.62mm pitch terminal
blocks
Consumption
No-load
4.2W@220VAC
Full-load
6.7W@220VAC
Environmental Limits
Working temperature
0~70℃
Storage temperature
-40~75℃
Working humidity
5%~95% (no condensation)
Protection grade
IP30 (metal shell)