3One data IES215-1GX-4G User manual

IES215-1GX-4G
Unmanaged Industrial Ethernet
Switch
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website: www.3onedata.com
Te l : [phone]
Fax: [phone]
【
Package Checklist
】
Please check the integrity of package and accessories while
first using the switch.
1.
Industrial Ethernet switch
2.
Lugs
3.
RJ45 network cable
4.
Warranty card
5.
Certification
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview
】
This product is 10Gigabit unmanaged wall-mounting industrial
Ethernet switch. Models as follows: IES215-1GX-4G (1
10Gigabit copper port + 4 Gigabit copper ports)
【
Panel Design
】
Front View
Rear View
Top view
Left view, right view
1. 10Gigabit copper port
2. Gigabit copper port
3. Terminal block for power input
4. Grounding screw
5. Power indicator
6. Running indicator
7. Gigabit Ethernet indicator (G1-G4)
8. 10Gigabit Ethernet indicator (X1)
9. Lugs
【
Mounting Dimension
】
Unit: mm
Notice Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【
Wall-mounted Device Mounting
】
Step 1 Adopt M3 screw to install the left/right lugs on the
left/right side of the device backboard.

Step 2 On the wall of device mounting, place the device on
the wall for reference or refer to the mounting
dimension to mark two screw positions.
Step 3 Nail M3 screws on the wall and keep 2mm
interspace reserved.
Step 4 Hang the device on two screws and slide
downward, then tighten the screw to enhance
stability, mounting ends.
【
Wall-mounted Device Disassembling
】
Step 1 Power off the device.
Step 2 Unscrew the screw on the wall about 2mm.
Step 3 Lift the device upward slightly; take out the device,
disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【
Power Supply Connection
】
The device provides 3-pin power supply input terminal blocks
and supports 1 DC power supply input which
supports anti-reverse connection and
overload protection. Voltage range: 24VDC
(12~36VDC)
【
Checking LED Indicator
】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Indicate
Description
PWR
ON
PWR is connected and
running normally
OFF PWR is disconnected or
running abnormally
RUN
Blinking
The system is running
normally
OFF The system is not running or
running abnormally
ON
System is running abnormally
Link/Act
(X1, G1-G4)
ON Ethernet port has established
a valid network connection
Blinking Ethernet port is in an active
network status
OFF
Ethernet port has not
established valid network
connection
【
Specification
】
Panel
10Gigabit copper port 100/1000/10000BASE-T
(10Gigabit port)
(10Gigabit/Gigabit/100M
self-adaption)
Gigabit copper port 10/100/1000Base-T(X)
self-adapting RJ45 port, half/full
duplex self-
adaption or forced
working mode, support MDI/
MDI-X self-adaption
Indicator
Power indicator, running
indicator, interface indicator
Switch Property
Backplane bandwidth
28G
Packet buffer size
2Mbit
MAC Address Table
16K
Power Supply
Power range
24VDC
（
12~36VDC
）
Access terminal block 3-
pin 5.08mm pitch terminal
block
Power Consumption
No-load
3.6W@24VDC
Full-load
7.7W@24VDC
Working Environment
Working temperature
-40~75
℃
Storage temperature
-40~85
℃
Working humidity
5%
～
95% (no condensation)
Protection grade
IP30(metal shell)