Abus Secvest IP User manual

FUAA10011
Secvest IP
wireless alarm centre
Installation and operating instructions (UK)
02032012

1 Contents
1
1. Contents
1.Contents 1
2.Preface 2
3.Conformity 2
4.Meaning of the symbols 3
5.Important safety information 3
6.Scope of delivery 7
7.Compatibility with ABUS products 8
8.Installation 9
9.Installation of the backup battery (backup power supply) 10
10.Display and setting elements 11
11.Labelling the Secvest IP 16
12.Putting into operation 16
13.Enclosed software 17
14.Configuration of the web server 18
15.Teaching the wireless components 66
16.Alarm types and notification 74
17.Resetting an alarm 75
18.Maximum system extension 75
19.Firmware display of wireless PCB 77
20.Information on additional ABUS products 77
21.Notes on maintenance 77
22.Technical data 78
23.Customer service and support 79
24.Explanation of terms 80

2 Preface
2
2. Preface
Dear customer,
Many thanks for your purchase of this Secvest IP wireless alarm centre. This product
is built according to state-of-the-art technology. It complies with current domestic and
European regulations. Conformity has been proven, and all related certifications are
available from the manufacturer on request (www.abus-sc.com). To ensure safe
operation, it is your obligation to observe these instructions! If you have any
questions, please contact your local specialist dealer. No part of the product may be
changed or modified in any way.
These instructions contain important installation and operation information. Store
these instructions in a safe place for future reference. These instructions are part of
the product. Bear this in mind if you pass the product on to others.
Disclaimer:
These operating instructions have been produced with the greatest care. Should you
discover any missing information or inaccuracies, please contact us under the
address shown.
ABUS Security-Center GmbH does not accept any liability for technical and
typographical errors, and reserves the right to make changes to the product and
operating instructions at any time and without prior warning.
We reserve the right to make changes to these instructions without prior notice. No
forms of guarantee are accepted for the contents of this document.
© ABUS Security-Center GmbH & Co. KG, 03 / 2012
3. Conformity
The declaration of conformity can be ordered from:
ABUS Security-Center GmbH & Co. KG
Linker Kreuthweg 5
86444 Affing
GERMANY
www.abus-sc.com
[email protected]

4 Meaning of the symbols
3
4. Meaning of the symbols
Disposal as per directive WEEE 2002/96 EC
At the end of its useful life, dispose of the product according to the
applicable legal requirements. Within the EU, the product and its
accessories must be collected and disposed of separately.
Devices displaying this symbol may not be disposed of as
domestic waste. Please contact your dealer or dispose of the
products at the local collection point for electronic waste.
This symbol indicates important notes in these operating
instructions, which must be observed.
This symbol indicates special tips and notes on the operation of
the unit.
5. Important safety information
5.1 Intended use
Only use the device for the purpose which it was designed and built for. Any other
use is considered inappropriate.
This device may only be used for the following purpose(s):
•This three-zone IP wireless alarm centre is used in combination with connected
wireless detectors, signallers, actuators and operating units for object
surveillance.
5.2 General
Before using the device for the first time, read the following instructions carefully and
pay attention to all warnings, even if you are already familiar with electronic devices.

5 Important safety information
4
Warning
All guarantee claims become invalid for damage caused by non-
compliance with these operating instructions.
We cannot be held liable for resulting damages.
Warning
We cannot be held liable in the event of material or personal damage
caused by improper operation or non-compliance with the safety
information.
All guarantee claims are invalid in such cases.
Keep this manual in a safe place for future reference.
If you pass on or sell the device, you must also include this user manual. This device
has been manufactured in accordance with international safety standards. Inspect
the device before putting it into operation. If the device shows signs of damage, do
not put it into operation.
5.3 Power supply
•Only operate this device through a power source which supplies the mains power
specified on the type plate of the power supply unit.
•If you are unsure of the power supply at the installation location, contact your
power supply company.
•Only operate this device with the device-specific power supply unit.
•This device uses Safety Extra Low Voltage (SELV). The circuits of the switch
outputs and the 13.8 V power supply also fall into this voltage range. SELV is a
low electrical current that offers special protection against electric shocks based
on its low level and insulation compared to higher voltage circuits.
Warning
The installation of additional equipment or modification of the device
invalidates your guarantee if not carried out by trained personnel.
Your guarantee is invalidated in the event of improper installation o
f
additional equipment or modifications.
5.4 Overloading/overvoltage
•Avoid overloading of mains sockets, extension cables and adapters as this can
result in fires or electric shocks.
•Use overvoltage protection to prevent damage caused by overvoltage (e.g.
electrical storms).

5 Important safety information
5
5.5 Cables
•Always hold cables by the connector, and do not pull the cable itself.
•Never touch the mains cable with wet hands, as this can lead to a short circuit or
electric shock.
•Never position the device, furniture or other heavy items on the cable. Ensure
that the cable does not become kinked, especially on the connector and sockets.
•Never knot the cable, and do not tie it to other cables.
•All cables should be laid so that they cannot be stepped on or cause an
obstruction.
•A damaged mains cable or power supply unit can cause a fire or electric shock.
Check the mains cable from time to time.
•Do not modify or manipulate the mains cable or plug.
•Do not use plug adapters or extension cables that do not conform to the
applicable safety standards, and do not make alterations to power supply cables
or mains cables.
5.6 Installation location/operating environment
•Install the device on the wall and do not place any objects in front of it.
•The device is not designed for operation in rooms subject to high temperatures
or moisture (e.g. bathrooms), or in excessively dusty rooms.
•Operating temperature and ambient humidity:
-10°C to +55°C, maximum 75% relative humidity. The device may only be
operated in moderate climate conditions.
Ensure the following:
•Sufficient ventilation must always be guaranteed – leave a gap of at least 10 cm
from all sides.
•The device must not be exposed to direct heat sources (e.g. heaters).
•The device must not be exposed to direct sunlight or strong artificial light.
•The device must not be placed in close proximity to magnetic fields
(e.g. loudspeakers).
•Naked flames (e.g. candles) must not be placed on or near the device.
•Contact with spraying or dripping water and aggressive liquids must be avoided.
•The device must not be operated in close proximity to water, and must not be
submerged under any circumstances (do not place objects containing water on
or near the device, such as vases or drinks).
•Foreign objects must not penetrate the device.

5 Important safety information
6
•The device must not be exposed to strong variations in temperature, as this can
lead to condensation and electrical short circuits.
•The device must not be exposed to excessive jolts or vibrations.
5.7 Care and maintenance
Maintenance is necessary if the device has been damaged. This includes damage to
the plug, mains cable and housing, penetration of the interior by liquids or foreign
objects, exposure to rain or moisture or when the device does not work properly or
has fallen.
•Disconnect the device from the mains power supply before maintenance (e.g.
cleaning).
•If smoke develops or unusual noises or odours are detected, then pull the mains
plug from the socket immediately and remove the backup battery. In such cases,
the device should not be used until it has been inspected by a qualified
technician.
•Clean the device housing with a damp cloth.
•Do not use solvents, white spirit or thinners as these can damage the surface of
the device.
•Do not use any of the following substances:
Salt water, insecticides, solvents containing chlorine or acids (ammonium
chloride) or scouring powder.
•Gently rub the surface with a cotton cloth until it is completely dry.
5.8 Accessories
•Only connect devices that are suitable for the intended purpose. Otherwise,
hazardous situations or damage to the device can occur.
5.9 Putting into operation
•Observe all safety and operating instructions before putting the device into
operation for the first time.
•Only open the housing during installation and when training the wireless
components.
Warning
If in doubt, have a specialist technician carry out assembly, installation
and connection of the device.
Improper or unprofessional work on the mains power supply puts both
you and other persons at risk.

6 Scope of delivery
7
5.10 Children and the device
•Do not allow children access to electrical devices. Never allow children to use
electrical devices without supervision. Children may not be able to accurately
detect possible risks. Small parts can be life-threatening if swallowed.
•Keep batteries away from small children. Call for medical assistance immediately
if a battery is swallowed.
•Keep packaging materials away from children (danger of suffocation).
•This device should not be used by children.
6. Scope of delivery
Individual alarm centre:
1 x Secvest IP wireless alarm centre
1 x power supply unit
1 x backup battery
1 x 1 metre network cable
1 x Quick guide
1 x CD-ROM (installation and operating instructions, Secvest IP Finder, labelling
templates)
1 x installation material (4 x wall plugs, 4 x screws)
1 x battery cable
2 x cable clips

7 Compatibility with ABUS products
8
7. Compatibility with ABUS products
Compatible
CASA10010 IP alarm module
FU59xx Secvest Key 2WAY wireless cylinder
FU8100 Secvest 2WAY wireless remote control
(integrated panic function not usable)
FU8130 Secvest 2WAY wireless additional lock (7010E)
FU8140 Secvest 2WAY wireless additional lock (7025E)
FU8150 Secvest wireless remote control
(integrated panic function not usable)
FU8200 Secvest 2WAY wireless info module
(No display of: status ready / internally active / entry-
and exit delay time)
FU8210 / FU8211 Secvest 2WAY wireless universal module
(only repeater function)
FU8220 / FU8222 Secvest 2WAY wireless outdoor siren
(Beep acknowledgement as of FU8222)
FU8230 Secvest 2WAY wireless indoor siren
FU8240 Secvest wireless socket
FU8300 Secvest 2WAY wireless panic alarm
FU8305 Secvest 2WAY wireless panic transmitter
FU8310 Secvest 2WAY wireless fire alarm
FU8320W/B Secvest 2WAY wireless magnetic contact
FU8321W/B Secvest 2WAY wireless magnetic contact
FU8325W/B/S Secvest 2WAY mini wireless magnetic contact
FU8330 Secvest 2WAY wireless flood detector
FU8340 / FU8341 Secvest 2WAY wireless smoke detector
FU8350 Secvest 2WAY wireless motion detector
FU8360 Secvest 2WAY animal-immune wireless motion
detector
FU8370 Secvest 2WAY wireless glass breakage detector
FU8380 Secvest 2WAY wireless vibration detector
FU8390 Secvest 2WAY wireless emergency transmitter
FU841xW/B FTS 96 E wireless window lock
FU842x Secvest 2WAY wireless window bar lock (FOS550E)
FU8430W/B/S Secvest 2WAY wireless window handle (FG350E)
FU8435W/B/S Secvest 2WAY wireless window handle plus
TVIP41550 PIR network camera
Not compatible
FU8110 Secvest 2WAY wireless control unit
FU8165 Secvest 2WAY wireless key switch

8 Installation
9
8. Installation
Key:
A) Wall tamper switch
B) Housing screw
C) Fixing holes on base plate
D) Cable opening
E) Tension relief (bar for fastening cable to cable clip)
Installation procedure:
1. Loosen the housing screw on the bottom narrow side and open the housing.
2. Using the back of the housing as a template, mark the drill holes (C).
Drill the holes for the fixing screws.
3. Guide the connection cable through the appropriate opening (D).
4. Connect the power supply to the terminal block with the correct polarity
(grey dashed wire is positive).
5. Connect the LAN cable (see following diagram).
A
B
C
C
E
D
13.8 V DC
(power supply unit)
Power supply for
optional BT2020
backup battery
IP