ADLINK Technology aTCA-80302PA User manual

aTCA-80302PA/PD
3U 2-slot Full-Mesh 40G AdvancedTCA® Shelf
User’s Manual
Manual Rev.: 1.0
Revision Date: September 19, 2018
Part No.: 50-1G046-1000

2
aTCA-80302PA/PD
Preface
Copyright 2018 ADLINK Technology, Inc.
This document contains proprietary information protected by copyright. All rights are reserved. No part
of this manual may be reproduced by any mechanical, electronic, or other means in any form without
prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order to improve reliability,
design, and function and does not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use or inability to use the product or documentation, even if advised of the
possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global environmental
preservation through compliance with the European Union's Restriction of
Hazardous Substances (RoHS) directive and Waste Electrical and Electronic
Equipment (WEEE) directive. Environmental protection is a top priority for
ADLINK. We have enforced measures to ensure that our products,
manufacturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their end of life,
our customers are encouraged to dispose of them in accordance with the
product disposal and/or recovery programs prescribed by their nation or
company.
Battery Labels (for products with battery)
廢電池請回收
California Proposition 65 Warning
WARNING: This product can expose you to chemicals including acrylamide, arsenic,
benzene, cadmium, Tris(1,3-dichloro-2-propyl)phosphate (TDCPP), 1,4-Dioxane,
formaldehyde, lead, DEHP, styrene, DINP, BBP, PVC, and vinyl materials, which are
known to the State of California to cause cancer, and acrylamide, benzene, cadmium, lead, mercury,
phthalates, toluene, DEHP, DIDP, DnHP, DBP, BBP, PVC, and vinyl materials, which are known to the
State of California to cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.

3
aTCA-80302PA/PD
Table of Contents
Preface................................................................................................................................2
1Safety..........................................................................................................................5
1.1 Safety Symbols used in this document.......................................................................... 5
1.2 General Safety Precautions........................................................................................... 5
1.3 References and Architecture Specifications.................................................................. 6
1.4 Terms and Acronyms .................................................................................................... 6
1.5 Hardware Platform.........................................................................................................7
2Shelf Front and Rear View........................................................................................8
3ATCA Backplane .......................................................................................................9
3.1 Logical to Physical Slot Mapping................................................................................... 9
3.2 Interfaces....................................................................................................................... 9
3.2.1 Fabric Interface................................................................................................9
3.2.2 Synchronization Clock Interface...................................................................... 9
3.2.3 Update Channel Interface................................................................................ 9
3.2.4 Intelligent Platform Management Interface...................................................... 9
3.2.5 Base Interface ............................................................................................... 10
3.3 Shelf FRU SEEPROM................................................................................................. 11
3.4 Logic Ground............................................................................................................... 11
4Air Filter....................................................................................................................12
4.1 Introduction...................................................................................................................... 12
5Shelf Ground Connection.......................................................................................13
5.1 Specification for the Shelf Ground connection cable....................................................... 13
6Fan Trays .................................................................................................................14
6.1 IPM Controller and Fan Control................................................................................... 15
6.2 Fan Tray Indicators...................................................................................................... 16
6.3 Fan Tray Signals ......................................................................................................... 17
6.4 Fan Tray Connector Pin Assignment........................................................................... 17
6.5 Fan Tray IPMB Addresses .......................................................................................... 18
6.6 Front Board Air Distribution......................................................................................... 18
6.7 Rear Board Air Distribution.......................................................................................... 19
7Power........................................................................................................................20
7.1 AC PEM.......................................................................................................................20
7.1.1 AC PEM Power Distribution........................................................................... 21
7.1.2 AC PEM Signals............................................................................................ 22
7.1.3 AC PEM Indicators ........................................................................................ 22
7.1.4 AC PEM Connector PIN Assignment............................................................. 23
7.2 DC PEM....................................................................................................................... 23
7.2.1 DC PEM Power Distribution........................................................................... 25

4
aTCA-80302PA/PD
7.2.2 DC PEM Signals............................................................................................ 25
7.2.3 DC PEM Indicators........................................................................................ 26
7.2.4 DC PEM Connector PIN Assignment ............................................................ 26
8Shelf Management...................................................................................................23
8.1 Shelf Managers ...........................................................................................................24
8.2 Introduction.................................................................................................................. 24
8.3 Front Panel Components............................................................................................. 26
8.4 Hardware Address.......................................................................................................26
9Technical Data.........................................................................................................27
9.1 Shelf Dimensions.........................................................................................................30
Getting Service ................................................................................................................32

5
aTCA-80302PA/PD
Hazardous voltage!
Thisistheelectricalhazardsymbol.Itindicatesthattherearedangerousvoltages
insidethe Shelf.
Caution!
Thisistheusercautionsymbol.Itindicatesaconditionwheredamageoftheequipment
or injuryof theservice personnel could occur. To reducethe risk ofdamageor injury,
followall stepsorproceduresasinstructed.
Danger of electrostatic discharge!
TheShelfcontainsstaticsensitivedevices.Topreventstaticdamageyoumustwearan
ESD wriststrap.
Warning!
Voltagesover60VDCcanbepresentinthisequipment.AsdefinedinthePICMG3.0
Speci- fication,thisequipmentisintendedtobeaccessed,tobe installedand
maintainedby qualifiedandtrainedservicepersonnelonly.
1 Safety
The intended audience of this User’s Manual is system integrators and
hardware/software engineers.
1.1 Safety Symbols used in this document
1.2 General Safety Precautions
• Service personnel must know the necessary electrical safety, wiring and
connection prac- tices for installing this equipment.
• Install this equipment only in compliance with local and national electrical codes.
• For additional information about this equipment, see the
PICMG 3.0 Specification (www.picmg.com).

6
aTCA-80302PA/PD
1.3 References and Architecture Specifications
• Pigeon Point Systems IPM Sentry Shelf-External Interface
Reference (www.pigeonpoint.com)
• PICMG®3.0 Revision 3.0 AdvancedTCA® Base
Specification (www.picmg.com)
1.4 Terms and Acronyms
Table 1: Terms and Acronyms
Term Definition
ATCA
Advanced Telecom Computing Architecture
Backplane Passive circuit board providing the connectors for the front boards. Power
distribution, management and auxiliary signal connections are supported
CDM Shelf FRU Data Module
ECN Engineering Change Notice
ESD Electrostatic Discharge
ETSI European Telecommunications Standards Institute
FRU Field Replaceable Unit
IPMB Intelligent Platform Management Bus
IPMC Intelligent Platform Management Controller
IPMI Intelligent Platform Management Interface
PCB Printed Circuit Board
PEM Power Entry Module
RTC
Real Time Clock
RTM
Rear Transition Module
Shelf Enclosure containing subrack, Backplane, boards, cooling devices, PEMs and
Fan Trays
VRTN Voltage Return

7
aTCA-80302PA/PD
1.5 Hardware Platform
The Shelf is 3 U high and 19“ rack mountable. The chassis is designed for easy
access of any Field Replaceable Units (FRU).
• 2 slot ATCA Backplane with 15 x interconnected Fabric Interface, Base
Interface in HUB/HUB or NODE/NODE configuration, bused IPMB interface,
supporting two 8U ATCA hub boards or node boards (depending on
chassis/backplane type)
• Mounting brackets for 19“ racks
• ESD Wrist Strap Terminals at front and rear
• Two dedicated slots for a Shelf Manager based on Pigeon Point ShMM-700
• One dedicated slot for a Schroff Shelf Alarm Panel (SAP) that provides Telco
Alarm inter- face, Alarm Status LEDs and serial interface for the Shelf Manager
• Two Front pluggable Fan Trays with 5 high speed fans per tray
• Removable air filter that meets the requirements of the Telcordia GR-78-CORE
specifica- tion.
• Two rear pluggable AC- or DC-Power Entry Modules, the same interface in the
subrack for AC PEM and DC PEM.
• Front pluggable air inlet filter

8
aTCA-80302PA/PD
2 Shelf Front and Rear View
Figure 1: Shelf Front View
1
Shelf Manager 1
8
DC PEM B
2
Fan Tray 1
9
Shelf Ground Terminal
3
Shelf Alarm Panel (SAP)
10
DC PEM A
4
ESD Wrist Strap Terminal
11
ESD Wrist Strap Terminal
5
Shelf Manager 2
12
AC PEM B
6
Fan Tray 2
13
AC PEM A
7
Air Filter

9
aTCA-80302PA/PD
3 ATCA Backplane
The 2-slot ATCA monolithic Backplane is completely passive and is not a field
replaceable unit. The backplane provides 40Gb/s connectivity (4 lanes with 10Gb/s)
and 2 ATCA slots in a:
• Hub/Hub configuration or
• Node/Node configuration
3.1 Logical to Physical Slot Mapping
The physical and logical slots are sequentially numbered from the lower to the upper slot.
Table 2: 2-Slot ATCA Backplane physical to logical slot mapping
Physical
Slot # Logical Slot
#
HW-Address
(Hex) IPMB-
Address (Hex)
Update
Channel
2 2 42 84
1 1 41 82
3.2 Interfaces
3.2.1 Fabric Interface
All 15 Fabric Channels of slot 1 are routed to the respective Fabric Channels of slot 2.
3.2.2 Synchronization Clock Interface
6 pairs of synchronization clocks are bused between both ATCA slots and
terminated at both ends.
3.2.3 Update Channel Interface
The Update Channels are wired between both ATCA slots. The Update Channel
can be used to pass data or routing information between two redundant ATCA
Boards.
3.2.4 Intelligent Platform Management Interface
The Shelf uses an Intelligent Platform Management Bus (IPMB) for
management communications among all ATCA Boards. The reliability of the
IPMB is improved by the addition of a second IPMB, with the two IPMBs
referenced as IPMB-A and IPMB-B.
The IPMB-A and IPMB-B are routed between the ATCA slots.

10
aTCA-80302PA/PD
3.2.5 Base Interface
Node/Node configuration
All 16 Base Channels of slot 1 are routed to the respective Base Channels of
slot 2.
Hub/Hub configuration
All Base Channels 2 - 16 of slot 1 are routed to the respective Base Channels of
slot 2. Base Channel 1 (ShMC) of slot 1 and 2 is cross connected to both dedicated
Shelf Manager slots.
Figure 2: Backplane Topology

11
aTCA-80302PA/PD
3.3 Shelf FRU SEEPROM
2 Shelf FRU SEEPROMS are located on the Backplane. The hardware address for
these SEEPROMs is 0xA4.
The SEEPROMs are the repository of the shelf specific information capabilities of
the system and other user configurable options. The SEEPROMs contain the list of
which slots are connected together, how the update channels are routed, how many
slots are in the system, what the maximum power is to each slot, serial number of
the shelf, backplane topology, etc. The Shelf Manager uses this information to
provide functions such as electronic keying, controlling the power state of the
system, etc.
The Shelf allows for 2 methods to access the chassis FRU data:
• An I2C connection from each Shelf Manager directly to the SEEPROMs on the
backplane.
• SEEPROMs on the backplane exposed as a FRU of the Fan Tray.
3.4 Logic Ground
Figure 3: Logic Ground
The ATCA backplane provides a mechanism to connect Logic Ground and Shelf
Ground. The backplane fixing screw (arrow) is isolated by a plastic washer. To
connect Logic Ground and Shelf Ground remove the screw, remove the plastic
washer and re-install the screw.
The default factory assembly isolates Logic Ground from Shelf Ground.

12
aTCA-80302PA/PD
4 Air Filter
Figure 4: Air Filter
4.1 Introduction
The ATCA Shelf provides a front replaceable air filter. The filter element is an open
cell polyurethane foam specially coated to provide improved fire retardation and
fungi resistance. It features deep loading, large dust holding capacity, low air
resistance, and complies with NEBS-GR-63-CORE.
There is a switch to detect whether an air filter is installed. This switch is exposed to
the Shelf manager as a presence sensor on the Fan Tray.
1
Air Filter
2
Filter Element

13
aTCA-80302PA/PD
5 Shelf Ground Connection
The ATCA Shelf provides a Shelf ground terminal at the left rear side. The Shelf
ground terminal provides two threads (M5) with a 16 mm spacing between thread
centers to connect a double-lug Shelf ground terminal cable.
Figure 5: Shelf Ground Terminal
12713815
Please note, that in a typical telecom environment, the VRTN path of
the -48V supply is grounded to Protective Earth (PE) of the building.
5.1 Specification for the Shelf Ground connection cable
Required wire size: AWG8
Required terminals: Use only double lug terminals (Terminal Used: PANDUIT part
no. LCD8- 14A-L).
Hazardous voltage!
Beforepowering-uptheShelf,makesurethattheShelfGroundterminalsare
connectedtoProtectiveEarth(PE)ofthebuilding.

14
aTCA-80302PA/PD
6 Fan Trays
The 2 Slot ATCA Shelf contains two interchangeable Fan Trays arranged in a side
to side configuration for maximum air flow. The Fan Trays are intelligent FRUs and
plugged-in at the left and right front of the Shelf.
Each Fan Tray contains five 60 mm fans (110 m³/h (64 CFM) each). The Fan Tray
is controlled via an on-board IPM controller.
Figure 6: Fan Tray
1
Green Fan Tray OK LED
4
Hot Swap push button
2
Red Fan Tray Alarm LED
5
DIP Switch
3
Blue Hot Swap LED
5

15
aTCA-80302PA/PD
6.1 IPM Controller and Fan Control
The on-board IPM controller is located on the Fan Tray and has 2 operation modes:
1. Shelf Manager Mode
As soon as a Shelf Manager is plugged-in and becomes active, the IPM controller
switches automatically into the Shelf Manager mode. The Shelf Manager performs
management of the Fan Tray through the two independent bussed IPMB
connections.
When the Fan Tray is first inserted into the system, the fans start at full speed and
then decrease to specified speed by Shelf Manager. The circuitry on-board the Fan
Tray uses a PWM signal to control the speed of all the fans. Lower speeds reduce
acoustic noise and power consumption and increase the lifetime of the fans.
The speed of each individual fan is monitored. If any of the fan speeds drops below
the desired fan speed, a System Event Log (SEL) entry is logged by the Shelf
Manager. The Shelf Manager then generates alerts and sets alarm conditions as
necessary.
The system is designed to run indefinitely with any single fan failure. When one fan
fails, all other fans are increased to full speed. The Fan Tray has sufficient cooling
capacity to keep the Shelf cooled with a single fan failure.
2. Autonomous Mode
When no Shelf Manager is present, the Fans are controlled by the IPM controller. The fan
speed depends on the setting of DIP switch on the controller board. With a Micro DIP switch
you can select either the exhaust temperature from the left Fan Tray as reference to control
the fan speed or fixed fan speed.
Table 3: Micro DIP switch settings
Bit 1
Bit 2
Bit 3
Description
0
0
0
Fixed
Speed, 50% of Full Speed
0
0
1
Fixed Speed, 70% of Full Speed
0
1
0
Fixed Speed, 90% of Full Speed
0
1
1
Fixed Speed, 100% of Full Speed
1
0
0
Exhaust Temperature 35 ~ 45 °C
1
0
1
Exhaust Temperature 40 ~ 50 °C
1
1
0
Exhaust Temperature 45 ~ 55 °C
1
1
1
Exhaust Temperature 50 ~60 °C
The default setting is 50% of full speed.

16
aTCA-80302PA/PD
Figure 7: Fan Control curves
6.2 Fan Tray Indicators
The front panel includes a green and red status LED and a blue hot-swap LED.
The Hot-Swap push button indicates to the Shelf Managers that the Fan Tray is
about to be removed. Its use is optional, but it is provided so that service personnel
can be trained to look for a blue LED to be illuminated on any active component
before removing it from the system. Once the operator pushes the Hot-Swap button,
the Shelf Manager is informed of the pending extraction. When the Shelf Manager
feels it is “safe“ to remove the Fan Tray, the blue Hot-Swap LED illuminates solid.
Table 4: LEDs on Fan Tray front panel
Color
Description
Status
Condition
Green
OK LED
Off
No Power to the Fan Tray
Solid green
Normal Operation
Red
Solid red
Attention Status (error condition)
Blue
Hot Swap LED
Off
No Power to the Fan Tray or not
OK to extract Fan Tray
Short blink
Preparing for extraction
Solid blue
Ready to remove

17
aTCA-80302PA/PD
6.3 Fan Tray Signals
The Fan Tray provides signals for:
• Voltage monitoring
• Status of the Hot Swap Controller
• Fan Speed
• Temperature
These signals are controlled by the IPM Controller on the PCB. The Shelf Manager
has access to these signals via IPMB.
6.4 Fan Tray Connector Pin Assignment
Description

18
aTCA-80302PA/PD
6.5 Fan Tray IPMB Addresses
Geographic address pins H2 at the Fan Tray Backplane connector determine the hardware
addresses of the devices.
Table 5: Fan Tray IPMB Addresses
HW-Addr.
IPMB Addr.
Fan Tray 1 (left)
0x2E
0x5C
Fan Tray 2 (right)
0x2D
0x5A
6.6 Front Board Air Distribution
The airflow is measured with impedance boards acc. to the PICMG 3.0 R3.0
specification. Front board pressure drop: 37 Pa at 0,85 m³/min
Figure 8: Front Board Air Distribution
Table 6: Front Air Flow
Zone 1 [CFM]
Zone 2 [CFM]
Zone 3 [CFM]
Zone 4 [CFM]
∑[CFM]
Slot 1
17,9 (30,5
m³/h)
17,7 (30,1
m³/h)
16,8 (28,5
m³/h)
17,1 (29,0
m³/h)
69,4 (30,5
m³/h)
Slot 2
17,0 (28,9
m³/h)
16,8 (28,5
m³/h)
16,1 (27,4
m³/h)
16,1 (27,4
m³/h)
66,1 (28,9
m³/h)
∑
34,9 (59,3
m³/h)
34,5 (58,6
m³/h)
32,9 (59,9
m³/h)
33,2 (58,4
m³/h)
135,5 (230
m³/h)

19
aTCA-80302PA/PD
6.7 Rear Board Air Distribution
The airflow is measured with impedance boards acc. to the PICMG 3.0 R3.0
specification. Rear board pressure drop: 24 Pa at 0,14 m³/min
Figure 9: Rear Board Air Distribution
Table 7: Rear Air Flow
[CFM]
Slot 1
16,7 (28,4 m³/h)
Slot 2
16,0 (27,2 m³/h)
∑
32,7 (55,6 m³/h)

20
aTCA-80302PA/PD
7 Power
The shelf supports AC- and DC-Power Entry Modules (PEMs). Both PEMs have
the same interface to the shelf.
The AC-PEM can be powered with 230 VAC line voltage. The specified
voltage range is from 180 VAC to 265 VAC .The Shelf supports redundant
power inputs but the two in- puts should be independently powered.
The DC-PEM can be powered using a regular telecommunication power
supply of -48/-60 VDC with a VDC return. The specified voltage range is from
-40.5 VDC to -72 VDC. The Shelf supports redundant power inputs but the
two inputs should be in- dependently powered.
7.1 AC PEM
Two pluggable redundant AC Power Entry Modules (PEM) are located at the rear
top side of the Shelf. The power input is provided by an AC mains/line module with
IEC 320-C14 connector and mains switch. The output voltage of the AC PEM is 48
VDC. Overcurrent protection is provided by a 40 A fuse in the output branch.
Figure 10: AC PEM
1
Green Fan Tray OK LED
4
Hot Swap push button
2
Red Fan Tray Alarm LED
5
IEC 320-C14 connector
3
Blue Hot Swap LED
6
Mains switch
7
Fuse
Hazardous voltage!
Before working ensure that the power is removed from the power connection
cables.
5