ADLINK Technology DMI-1210 User manual

Leading EDGE COMPUTING
Manual Rev.: 1.1
Revision Date: February 21, 2020
Part No: 50-1Z284-1010
DMI-1210
Driver Machine Interface
User’s Manual

ii Revision History
Leading EDGE COMPUTING
Revision History
Revision Release Date Description of Change(s)
1.0 2019-02-20 Initial release
1.1 2020-02-21 Correct USB 1.1 M8 Connector pinout

Preface iii
DMI-1210
Preface
Copyright © 2019, 2020 ADLINK Technology Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsi-
bility to global environmental preservation
through compliance with the European Union's
Restriction of Hazardous Substances (RoHS)
directive and Waste Electrical and Electronic
Equipment (WEEE) directive. Environmental
protection is a top priority for ADLINK. We have
enforced measures to ensure that our products,
manufacturing processes, components, and raw
materials have as little impact on the environment as possible.
When products are at their end of life, our customers are encour-
aged to dispose of them in accordance with the product disposal
and/or recovery programs prescribed by their nation or company.
Battery Labels
ᑜ㔚ᳰ⺧࿁ᡴ

iv Preface
Leading EDGE COMPUTING
California Proposition 65 Warning
WARNING: This product can expose you to chemicals
including acrylamide, arsenic, benzene, cadmium,
Tris(1,3-dichloro-2-propyl)phosphate (TDCPP), 1,4-Diox-
ane, formaldehyde, lead, DEHP, styrene, DINP, BBP, PVC, and
vinyl materials, which are known to the State of California to cause
cancer, and acrylamide, benzene, cadmium, lead, mercury,
phthalates, toluene, DEHP, DIDP, DnHP, DBP, BBP, PVC, and
vinyl materials, which are known to the State of California to cause
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov.
TrademarksProduct names mentioned herein are used for identi-
fication purposes only and may be trademarks and/or registered
trademarks of their respective companies.
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.

Table of Contents v
DMI-1210
Table of Contents
Revision History...................................................................... ii
Preface.................................................................................... iii
List of Figures........................................................................ ix
List of Tables.......................................................................... xi
1 Introduction ........................................................................ 1
1.1 Overview.............................................................................. 1
1.2 Features............................................................................... 1
1.3 Package Contents ............................................................... 2
2 System Description............................................................ 5
2.1 DMI-1210 Specifications...................................................... 5
2.2 Block Diagram ..................................................................... 7
2.3 Mechanical Layout............................................................... 8
2.4 Mechanical Dimensions..................................................... 11
2.5 Power Specifications ......................................................... 12
2.5.1 Power Consumption..................................................... 12
2.5.2 System Power Features............................................... 13
3 Getting Started ................................................................. 15
3.1 Removing the Rear Cover ................................................. 15
3.2 Installing a PC/104 MVB Module (optional) ....................... 18
3.3 Installing Wi-Fi and LTE Modules (optional) ...................... 21
3.4 Installing a Mini PCIe CAN Bus Module (optional) ............ 23
3.5 Mounting ............................................................................ 24
3.6 CFast Card Installation ...................................................... 26
3.7 Connections....................................................................... 27
3.8 Starting Up the System...................................................... 29
3.9 Driver Installation ............................................................... 30

vi Table of Contents
Leading EDGE COMPUTING
3.9.1 Windows....................................................................... 30
3.9.2 Linux Drivers ................................................................ 40
4 Display Utilities................................................................. 41
4.1 Calibrating the Touch Panel - Ubuntu................................ 41
4.2 Reading the Ambient Light Sensor .................................... 43
4.3 Display Brightness Control................................................. 44
5 Interfaces........................................................................... 45
5.1 Status LEDs ....................................................................... 45
5.2 Pin Definitions .................................................................... 46
6 BIOS................................................................................... 55
6.1 Introduction ........................................................................ 55
6.2 Entering BIOS Setup.......................................................... 55
6.3 Main Setup......................................................................... 59
6.3.1 BIOS Information.......................................................... 59
6.3.2 System Information ...................................................... 60
6.3.3 System Time/System Date........................................... 60
6.3.4 Board Information......................................................... 61
6.4 Advanced Menu ................................................................. 62
6.4.1 CPU Configuration ....................................................... 63
6.4.2 Graphic Configuration ............................................................ 64
6.4.3 Power Management ..................................................... 65
6.4.4 Power Consumption..................................................... 66
6.4.5 System Management ................................................... 66
6.4.6 Thermal Management .................................................. 68
6.4.7 Watchdog Timer ........................................................... 69
6.4.8 Super IO Configuration ................................................ 69
6.4.9 Serial Port x Configuration ........................................... 70
6.4.10 Serial Console Redirection ................................................... 70
6.4.11 Network Stack Configuration........................................ 73
6.4.12 Trusted Computing....................................................... 73
6.4.13 USB Configuration ....................................................... 73

Table of Contents vii
DMI-1210
6.4.14 Intel I210 Gigabit Network Connection.............................. 74
6.5 Chipset Menu..................................................................... 75
6.5.1 North Bridge ................................................................. 75
6.5.2 South Bridge ................................................................ 75
6.5.3 Uncore Configuration ................................................... 76
6.5.4 South Cluster Configuration ......................................... 77
6.5.5 HD-Audio Configuration ............................................... 77
6.6 Security Menu.................................................................... 84
6.6.1 Secure Boot ................................................................. 86
6.7 Boot Menu ......................................................................... 87
6.8 Save & Exit Menu .............................................................. 88
Important Safety Instructions.............................................. 89
Getting Service...................................................................... 91

viii Table of Contents
Leading EDGE COMPUTING
This page intentionally left blank.

List of Figures ix
DMI-1210
List of Figures
Figure 2-1: DMI-1210 Block Diagram................................................. 7
Figure 2-2: DMI-1210 Front Layout.................................................... 8
Figure 2-3: DMI-1210 Rear I/O Layout............................................... 9
Figure 2-4: DMI-1210 Side I/O Layout ............................................. 10
Figure 2-5: DMI-1210 Bottom I/O Layout ......................................... 10
Figure 2-6: DMI-1210 Dimensions ................................................... 11
Figure 3-1: DMI-1210 Mounting Hole Locations .............................. 24
Figure 3-2: Mounting the DMI-1210 ................................................. 25
Figure 5-1: Internal USB 2.0 Header (CN16) Location .................... 53

xListofFigures
Leading EDGE COMPUTING
This page intentionally left blank.

List of Tables xi
DMI-1210
List of Tables
Table 2-1: DMI-1210 Specifications.................................................. 5
Table 5-1: Status LED Definitions................................................... 45
Table 5-2: COM1/COM2 Serial Port Pinout.................................... 46
Table 5-3: USB 1.1 M8 Connector Pinout....................................... 46
Table 5-4: GbE1/GbE2 M12 Connector Pinout............................... 47
Table 5-5: Audio M8 Connector Pinout........................................... 47
Table 5-6: MVB Bus Female DB9 Connector Pinout...................... 48
Table 5-7: MVB Bus Male DB9 Connector Pinout .......................... 49
Table 5-8: CAN Bus Male DB9 Connector Pinout .......................... 50
Table 5-9: DC Power Input Pinout .................................................. 50
Table 5-10: USB2 (USB 3.0) Pinout ................................................. 51
Table 5-11: CFast Socket Pin Definition ........................................... 52
Table 5-12: Internal USB 2.0 Header (CN16) Pinout........................ 53

xii List of Tables
Leading EDGE COMPUTING
This page intentionally left blank.

1
DMI-1210
1 Introduction
1.1 Overview
The DMI-1210 is a 12.1” Driver Machine Interface panel PC
designed specifically for the railway industry, equipped with Intel
Atom® x5-E3930 processor (formerly Apollo Lake), resistive
touch, and MVB interface. It can be applied as an HMI unit for
driver’s desks, control panel for passenger information systems,
surveillance system control/display unit or in railway diagnostics
and communications applications.
1.2 Features
XIntel Atom® x5-E3930 processor, 1.8GHz
X12.1” color display: 4:3, 1024x768 pixels, 600cd/m2,
X5-wire resistive touch
XSoftware controlled backlight
XMVB/CAN bus support by PC/104 or Mini PCIe add-on
modules
XBuilt in GNSS and two Mini PCIe card slots for cellular
modem with USIM
X+24/+36/+72/+110 VDC nominal power input (EN50155
compliant)
XIP65 front and IP20 rear ingress ratings (IP42 rear available
by request)

2
Leading EDGE COMPUTING
1.3 Package Contents
Please check that your package contains the items below. If you
discover damaged or missing items, please contact your vendor.
XDMI-1210 Driver Machine Interface Panel PC (features
dependent on specific model ordered)
XMounting screw kit
Optional Accessories
Starter Cable Kit (P/N: 91-95239-000E)
X1x 4-pin A-coded M12 power supply cable
X2x 8-pin A-coded M12 to RJ45 Ethernet cable
X1x 4-pin M8 to Type A USB 1.1 cable
X1x 6-pin M8 to microphone and speaker cable
X2x 9-pin D-sub male-to-female cables for MVB
PC/104 MVB Kit (P/N: 91-95239-200E)
X1x PC/104 MVB card (duagon D113L.T.-P4B2, PD only,
EMD type)
X1x 9-pin D-sub male-to-female cable
X1x 9-pin D-sub female-to-male cable
Mini PCIe Card MVB Kit (P/N: 91-95239-100E)
X1x Mini PCIe MVB card (duagon D017M-P-T-I1-Y30C-M3,
PD only, EMD type)
X1x Y-split cable to 9-pin D-sub 1x male + 1x female
Mini PCIe Card CAN Bus Kit (P/N: 91-95239-300E)
X1x Mini PCIe CAN card (ANTZER FARO-HS100)
X1x Y-split cable to 9-pin D-sub 2x male

3
DMI-1210
Mini PCIe Card Cellular Kit 01 (for TW, China)
(P/N: 91-95239-400E)
X1x Mini PCIe GSM/TD-SCDMA/CDMA/WCDMA/LTE mod-
ule (SIMCOM SIM7100C-PCIE)
X2x external antennas (P/N: 30-60099-0000)
X2x internal RF cables (P/N: 30-60066-0000)
Mini PCIe Card Cellular Kit 02 (for Europe)
(P/N: 91-95239-500E)
X1x Mini PCIe GSM/TD-SCDMA/CDMA/WCDMA/LTE mod-
ule (SIMCOM SIM7100-PCIE)
X2x external antenna (P/N: 30-60099-0000)
X2x internal RF cables (P/N: 30-60066-0000)
Mini PCIe card Wi-Fi/BT Kit (P/N: 91-95239-600E)
X1x Mini PCIe GSM/TD-SCDMA/CDMA/WCDMA/LTE mod-
ule (AMPAK AP12356_I)
X2x external antennas (P/N: 30-60125-0000-A0)
X2x internal RF cables (P/N: 30-60122-0000)
WARNING:
DO NOT install or apply power to equipment that is damaged
or if there is missing/incomplete equipment. Retain the ship-
ping carton and packing materials for inspection. Please con-
tact your ADLINK dealer/vendor immediately for assistance.
Obtain authorization from your dealer before returning any
product to ADLINK.

4
Leading EDGE COMPUTING
This page intentionally left blank.

5
DMI-1210
2 System Description
2.1 DMI-1210 Specifications
Display
Display Size 12.1” color display
Resolution 1024x768 pixels (4:3)
Brightness 600 cd/m2
Contrast Ratio 700:1 typical
Touchscreen 5-wire resistive touch
System Components
Processor Intel Atom® x5-E3930 processor, 1.3GHz dual-core supporting
ECC (TDP 6.5W)
Memory DDR3L-1600GHz 4GB by SODIMM (optional 8GB)
Storage 1x CFast slot, externally accessible with cover
eMMC 5.0 up to 64GB (supported by request)
Input/Output
Ethernet 2x external GbE ports via M12 connector based on Intel® I210-IT 2kV isolation
Supports WOL and teaming
USB 1x USB 1.1 port via M8 connector with 2kV isolation
1x USB 3.0 Type A port with dust cover for maintenance
Serial 2x RS232/422/485 serial ports via DB-9
Audio Mic-in and Line-out port via M8 connector
Internal
Expansion
2x full size Mini PCIe slots for cellular modem or WLAN modules,
compliant to Mini PCIe card spec v1.2 (PCIe and USB 2.0)
2x micro-SIM slots
1x USB 2.0 wafer connector onboard
MVB/CAN MVB or CAN supported by PC/104 or Mini PCIe card with two
DB-9 outputs
GNSS Built-in 72 channel high sensitivity GNSS receiver
GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1I, Galileo E1B/C
Antennas 4x antenna cutouts for wireless functions
1x antenna cutout for GNSS
Light Sensor Sensor on front bezel to detect ambient illuminance
Table 2-1: DMI-1210 Specifications

6
Leading EDGE COMPUTING
Status LEDs
Power 1x power LED
Ethernet 2x Ethernet port activity LEDs
Serial 2x Tx activity LEDs, 2x Rx activity LEDs
Power
Input 4-pin A-coded M12 connector +24V/+36V/+72V/+110VDC nominal power input (16.8V to
137.5V, EN50155 compliant)
Buttons System reset & power button
Power
Consumption TBD
Mechanical
Dimensions 310 x 248 x 87.3 mm (w/o power connector)
Weight TBD
Ingress Rating IP65 front, IP20 rear (IP42 rear by request)
Mounting Panel mount (cut-out: 274.5 x 216.9 mm)
Environmental
Operating
Temperature -25°C to +70°C, EN50155 T3 class
Storage
Temperature -40°C to +85°C
Humidity 10-90% RH operating, non-condensing
5-95% RH storage, EN 60068-2-30, EN 50155
Vibration EN50155 standard, method EN61373: 2010, Category 1 Class B
Shock EN50155 standard, method EN61373: 2010, Category 1 Class B
Safety EN50153
Fire Protection EN45545-2:2013+A1:2015
Altitude 4572 m (15000 ft) at 25°C (MIL-STD-810G Method 500.5,
Procedure II2)
Software
BIOS AMI BIOS
Board
Management ADLINK SEMA 3.5 for WDT, hardware monitor, and fail-safe dual BIOS
Operating
System Linux Ubuntu 16.04 LTS, QT compatible, 64-bit Windows 10
Table 2-1: DMI-1210 Specifications

7
DMI-1210
2.2 Block Diagram
Figure 2-1: DMI-1210 Block Diagram
Intel
Apollo Lake
Main Board
Intel® Atom™ x5-E 3930
Intel® Atom™ x7-E 3950
Power
Board
5-
wire
LVDS &
Backlight
Res.
Touch
Panel
Mini PCIe
Con. x1
3G/4G or
Wi-Fi
Module
SODIMM
DDR3L
Socket
AFM
Board
PC/104
Con.
Mini PCIe
MVB/CAN
Module
Opt.
RP-SMA
Port x2
DB-9
Conn. x2
CFast
Slot
M.2
Slot
GPS
Module SMA
Port x1
Ethernet
M12 Port x2
USB 1.1
M8 Port x1
Mini PCIe
Con. x1
SIM
Slot
SIM
Slot
32 func.
key
box header
8x GPIO
Wafer
Backlight/
Volume key
Wafer
Power
M12 Con.
+24/+36V or
+72+110VDC
(+/- 40%) input
Light
Sensor
Cap.
Touch
Panel
Opt. US B
Camera
or
Dongle
Line-out,
Mic-in
M8 Port x1
Backlight/
Volume key
12V
Opt.
PC/104
MVB/CAN
Module
Power LED
RS232/
422/485
Port x2
I2C
USB 2.0
Wafer x2
LED Indicators
LAN x2
COM x 4
12.1"
LCM
Module
USB 3.0
Type A x1
right angle
PCBA
Internal
IO
Board-to-Board
cable
External
IO
3G/4G or
Wi-Fi
Module
RP-SMA
Port x2
PCIe
& USB x1
PCIe
& USB x1
SATA
12V, 5V, &
3v3 Bus
PCIe x4
USB 2.0 x2
USB 3.0 x2
LPC

8
Leading EDGE COMPUTING
2.3 Mechanical Layout
Front View
The status LEDs are located on the right side of the bezel and the
ambient brightness sensor at the top of the bezel as shown.
Figure 2-2: DMI-1210 Front Layout
Power
GbE Activity
Serial Port
Tx/Rx Activity
Ambient Brightness Sensor