ADLINK Technology cPCI-R6500 Series User manual

Advance Technologies; Automate the World.
Manual Rev.: 0.10 Preliminary
Revision Date: October 23, 2015
Part No: 50-15084-1000
cPCI-R6500
6U CompactPCI® Rear Transition Module
MXM Graphics Carrier
User’s Manual

ii Revision History
Revision History
Revision Release Date Description of Change(s)
0.10 2015/10/23 Preliminary release

Preface iii
cPCI-R6500
Preface
Copyright 2015 ADLINK Technology, Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro-
pean Union's Restriction of Hazardous Substances (RoHS) direc-
tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu-
facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.

iv Preface
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.

Table of Contents v
cPCI-R6500
Table of Contents
Revision History...................................................................... ii
Preface.................................................................................... iii
List of Figures....................................................................... vii
List of Tables.......................................................................... ix
1 Introduction ........................................................................ 1
1.1 Overview.............................................................................. 1
1.2 Features............................................................................... 2
1.3 Block Diagram ..................................................................... 3
1.4 Package Contents ............................................................... 4
2 Specifications..................................................................... 5
2.1 cPCI-R6500 General Specifications .................................... 5
2.2 I/O Connectivity ................................................................... 6
2.3 GPU..................................................................................... 6
3 Board Interfaces................................................................. 7
3.1 cPCI-R6500 Board Layout................................................... 7
3.2 cPCI-R6500D Assembly Layout .......................................... 8
3.3 cPCI-R6501D Assembly Layout .......................................... 9
3.4 cPCI-R65N0 Assembly Layout.......................................... 10
3.5 cPCI-R6500 Series Faceplate........................................... 11
3.6 Connector Pin Assignments .............................................. 12
3.7 Switch Settings .................................................................. 22
Important Safety Instructions.............................................. 25
Getting Service...................................................................... 27

vi Table of Contents
This page intentionally left blank.

List of Figures vii
cPCI-R6500
List of Figures
Figure 1-1: cPCI-R6500 Functional Block Diagram...........................3
Figure 2-1: cPCI-R6500 General Specifications................................6
Figure 3-1: cPCI-R6500 Board Layout - Component Side.................7
Figure 3-2: cPCI-R6500D Assembly Layout......................................8
Figure 3-3: cPCI-R6501D Assembly Layout......................................9
Figure 3-4: cPCI-R65N0 Assembly Layout......................................10
Figure 3-5: cPCI-R6500 Series Faceplate.......................................11

viii List of Figures
This page intentionally left blank.

List of Tables ix
cPCI-R6500
List of Tables
Table 2-1: cPCI-R6500(D) I/O Connectivity......................................6
Table 3-1: DVI-I Connector Pin Definition.......................................12
Table 3-2: DVI-I Connector Pin Definition.......................................13
Table 3-3: CompactPCI J3 Connector Pin Definition......................20
Table 3-4: CompactPCI J5 Connector Pin Definition......................21
Table 3-5: COM2 Mode Switch Settings.........................................22
Table 3-6: LAN Control Switch Settings..........................................23

xListofTables
This page intentionally left blank.

Introduction 1
cPCI-R6500
1 Introduction
1.1 Overview
The cPCI-R6500 Series is 6U CompactPCI rear transition module
(RTM) designed for use with ADLINK 6U CompactPCI CPU
blades. The cPCI-R6500 is an RTM equipped with an ATI or
NVIDIA MXM graphics module to provide additional graphics per-
formance for embedded applications and supports comprehensive
rear I/O functionality. Dual independent display output is via two
DVI ports and an onboard Realtek ALC262 High Definition Audio
Codec provides analog audio output from the audio controller on
the CPU blade. The cPCI-R6500 requires a compatible 6U Com-
pactPCI backplane with rear I/O support and correctly configured
CPU blade.
Three models are available: the cPCI-R6500D and cPCI-R6501D
(8HP) for ATI MXM graphics modules and the cPCI-R65N0D for
NVIDIA MXM graphics modules. The cPCI-R6500D is an 8HP
RTM equipped with two DVI ports, two GbE ports, two USB Type
A ports, one COM port (RS-232/422/485 selectable), and PS/2
keyboard mouse on the faceplate. The cPCI-R6501D is an 8HP
RTM that provides two DVI ports, two GbE ports, one USB Type A
port, and space to mount a 2.5" SATA drive for onboard storage
requirements. The cPCI-R65N0D is an 8HP RTM equipped with
two DVI ports, two GbE ports, one USB Type A port, and one
COM port (RS-232/422/485 selectable), and PS/2 keyboard
mouse on the faceplate.

2Introduction
1.2 Features
X6U CompactPCI RTM in 8HP width form factor
XCompliant with CompactPCI Specification 2.0, Rev. 3.0
XCompliant with CompactPCI Packet Switching Backplane
Specification PICMG 2.16 Rev. 1.0
X64-bit/66 MHz CompactPCI interface based on PCI specifica-
tions
XRealtek ALC262 HD Audio codec and Mic-in, Line-in, Line-out
via onboard 10-pin audio box header
XTwo DVI-I ports for dual independent displays (MXM graphics
module dependent)
XOne DB-9 serial port supporting RS-232/422/485 and one
RS-232 via 10-pin box header supporting TX/RX only
XOne USB 2.0 Type A port, 2x USB 2.0 via box header
XTwo Gigabit Ethernet ports from processor blade by PICMG
2.16
XOne PS/2 keyboard mouse on faceplate (cPCI-R6500D,
cPCI-R65N0)
XThree SATA 7-pin connectors
X2.5” drive space on cPCI-R6501D

Introduction 3
cPCI-R6500
1.3 Block Diagram
Figure 1-1: cPCI-R6500 Functional Block Diagram
PCIE x4
TX, RX, GND RS-232 10-pin box header
SATA 7-pin connector
RS
-
232/422/485
SATA0 MXM 3.0
PS/2 KB/MS
USB x1
LAN x2 (PICMG 2.16)
SATA 1/2 SATA 7-pin connector x2
HDA
LAN
Mic-in, Line-out Line-in,
10-pin header
DVI-I
DVI-I
KB/MS 10-pin header
rJ5
rJ3
LAN
ALC262
L1 L2
PS/2
KB/MS
USB x2
PS/2 KB/MS
10-pin box heade
r
DB-9
USB
USB USB
USB x2 10
-
pin header

4Introduction
1.4 Package Contents
The cPCI-R6500 is packaged with the following components. If
any of the items on the contents list are missing or damaged,
retain the shipping carton and packing material and contact the
dealer for inspection. Please obtain authorization before returning
any product to ADLINK.
XcPCI-R6500 Series MXM carrier
XMXM graphics module, model dependent on model
selected (installed)
X2.5" drive bracket kit (cPCI-R6501D only)
XAuxiliary power cord (4-pin Molex to 6-pin RTM onboard
connector, 20cm)
CAUTION:
This product must be protected from static discharge and
physical shock. Never remove any of the components
except at a static-free workstation. Use the anti-static bag
shipped with the product when putting the board on a sur-
face. Wear an anti-static wrist strap properly grounded on
one of the system's ESD ground jacks when installing or
servicing system components.

Specifications 5
cPCI-R6500
2 Specifications
2.1 cPCI-R6500 General Specifications
Standards • CompactPCI® Specification 2.0, Rev. 3.0
• CompactPCI® Packet Switching Backplane Specification
PICMG 2.16 Rev. 1.0
Form Factor • Standard 6U CompactPCI® Rear Transition Module
• Board size: 233.35mm x 80mm
• Dual-slot (8HP, 40.64mm)
• CompactPCI® connectors rJ3 and rJ5
GPU • PCI Express x4 interface through rJ5
• Dependent on the MXM module selected
Audio • Realtek ALC262 HD Audio codec
Faceplate I/O cPCI-R6500D
• 2x 10/100/1000BASE-T Ethernet ports
• 2x USB 2.0 Type A ports
• 2x DVI-I ports from MXM module
• 1x DB-9 COM port (RS-232/422/485)
• 1x PS/2 Mini-DIN keyboard/mouse
cPCI-R6501D
• 2x 10/100/1000BASE-T Ethernet ports
• 1x USB 2.0 Type A ports
• 2x DVI-I ports from MXM module
cPCI-R65N0D
• 2x 10/100/1000BASE-T Ethernet ports
• 1x USB 2.0 Type A ports
• 2x DVI-I ports from MXM module
• 1x DB-9 COM port (RS-232/422/485)
• 1x PS/2 Mini-DIN keyboard/mouse
Onboard
Peripherals • 3x 7-pin SATA connectors • 1x RS-232/422/485 box header (COM2)
• 1x RS-232 10-pin box header (COM1, TX, RX signals only)
• 1x KB/MS 10-pin box header
• 1x USB 10-pin box header (2 ports)
• 1x Mic-in/Line-out 10-pin box header
OS
Compatibility • Microsoft Windows 7 32/64-bit • Microsoft Windows Server 2003 32/64-bit
• Microsoft Windows Server 2008 32/64-bit
• Red Hat Enterprise Linux 6.0 64-bit
(dependent on CompactPCI processor blade)

6 Specifications
Figure 2-1: cPCI-R6500 Series General Specifications
2.2 I/O Connectivity
Table 2-1: cPCI-R6500 Series I/O Connectivity
2.3 GPU
The GPU specification is dependent on the MXM module selected.
Environmental • Operating Temperature: 0 °C to +60 °C
• Extended Temperature: -20 °C to +70 °C (by screening)
Function cPCI-R6500D cPCI-R6501D cPCI-R65N0
Faceplate Board Faceplate Board Faceplate Board
LAN Y x2 - Y x2 - Y x2 -
USB Y x2 Y x2 Y x1 Y x2 Y x1 Y x1 (box
header)
COM Y x1 Yx1(RS-232 TX/RX,
box header) Y x1 Yx1(RS-232
TX/RX,
box header) Y x1 Yx1(RS-232
TX/RX,
box header)
DVI-I Y x2 - Y x2 - Y x2 -
Serial ATA - Y x3 - Y x3 - Y x3
KB/MS - Y x1 - Y x1 Y x1 -
Audio -Y x1
(box header) -Y x1 (box header) -Y x1 (box header)
2.5” drive
space -- -Yx1- -

Board Interfaces 7
cPCI-R6500
3 Board Interfaces
This chapter illustrates the board layout, connector pin
assignments, and switch settings to familiarize users with the
cPCI-R6500.
3.1 cPCI-R6500 Board Layout
Figure 3-1: cPCI-R6500 Board Layout - Component Side
rJ1/2 CompactPCI connectors COM1/2 Serial port box header
CN1 MXM connector HDA1 Audio box header
CN4/5/6 SATA connectors LAN1 LAN connectors (RJ-45)
CN3 Auxiliary Power connector SW1 COM2 mode switch
CN9 Fan power connector SW2/SW3 LAN switches
CN10 SATA Power connector USB1 USB box header
CN9
CN4
CN5
CN6
PS/1
COM1
HDA1
USB1
COM2
CN3
CN10
rJ1
rJ2
SW3
SW1
SW2
CN1

8 Board Interfaces
3.2 cPCI-R6500D Assembly Layout
Figure 3-2: cPCI-R6500D Assembly Layout
PS/2 KB/MS
USB
COM
USB
LAN
DVI-D
DVI-I
MXM Thermal
Module

Board Interfaces 9
cPCI-R6500
3.3 cPCI-R6501D Assembly Layout
Figure 3-3: cPCI-R6501D Assembly Layout
MXM Thermal
Module
USB
LAN
DVI-D
DVI-I
2.5”
SATA
Drive

10 Board Interfaces
3.4 cPCI-R65N0 Assembly Layout
Figure 3-4: cPCI-R65N0 Assembly Layout
USB
LAN
DVI-D
DVI-I
COM
PS/2 KB/MS
MXM Thermal
Module