ADLINK Technology USB-7230 User manual

USB-7230/7250 Quick Start Guide Rev. 2.00
USB-7230/7250
USB 2.0-based Digital I/O Module
Getting Started Package Contents
Your package should contain:
• Rail mount kit
• ADLINK All-in-One CD
• Quick Start Guide
(this document)
• USB-7230/7250
• Stand
• USB cable (2m)
• 2X 20-pin removable
screw terminals
P/N 50-41039-5000 Nov. 11, 2016
Features
Installing the Driver
Connecting the USB-7230/7250
1. Connect the USB-7230/7250 module to one USB 2.0 or 3.0 port on the
computer using the included USB cable
2. The first time the USB-7230/7250 module is connected, a New Hardware
message appears. It will take around 6 seconds to load the firmware.
When complete, the LED indicator on the rear of the USB DAQ module
changes from amber to green and the New Hardware message closes.
The USB-7230/7250 module can now be located in the hardware
Device Manager, as shown.
• USB 2.0, USB bus powered
• Programmable digital filter
clears input channels
• Programmable DO/Relay initial
status
• Up to 2500 VRMS isolation
voltage
• Removable screw terminals
• Lockable USB cable for secure
connectivity
• Ready-to-use testing application
(U-Test) included
1. Download the latest UD-DASK driver & U-Test from:
http://www.adlinktech.com/ and run.
2. Follow the installation instructions
Check product package
Install USB-7230/7250
driver (UD-DASK)
& utility (U-Test)
Connect USB-7230/7250
to USB 2.0/3.0 port
Perform quick test with
U-Test utility

USB-7230/7250 Quick Start Guide Rev.
P/N 50-41039-5000 Nov. 11, 2016
Advance Technologies
Automate the World
Web: http://www.adlinktech.com
Service: [email protected]
Tel: [phone]
Fax: [phone]
Copyright 2016 ADLINK Technology, Inc.
Contents and specifications subject to change
without notice.
Contact ADLINK
Pin Connections Quick Testing with U-Test
1. Connect the signal to be monitored and controlled to the USB-7230/7250
2. Launch the U-Test Utility from either the Start menu, or
C:\ADLINK\U-test\U-Test.exe
3. Once the connected USB-7230/7250 is detected, configure the DI/O or
counter settings and run to implement quick testing
USB-7230 U-Test
USB-7250 U-Test
USB-7230 Pin Assignment USB-7250 Pin Assignment
Pin
F u n c t i on
Pin
Fu ncti on
20
VDD
40
DO15
19
DO7
39
DO14
18
DO6
38
DO13
17
DO5
37
DO12
16
DO4
36
DO11
15
DO3
35
DO10
14
DO2
34
DO9
13
DO1
33
DO8
12
DO0
32
IGND
11
IGND
31
IGND
10
CNT0
30
CNT1
9
CGND
29
COM
8
DI7
28
DI15
7
DI6
27
DI14
6
DI5
26
DI13
5
DI4
25
DI12
4
DI3
24
DI11
3
DI2
23
DI10
2
DI1
22
DI9
1
DI0
21
DI8
Pin
F u n c t i on
Pin
Fu ncti on
20
NO7
40
GND1
19
COM7
39
CNT1
18
NO6
38
GND0
17
COM6
37
CNT0
16
NO5
36
DI7L
15
COM5
35
DI7H
14
NO4
34
DI6L
13
COM4
33
DI6H
12
NC3
32
DI5L
11
NO3
31
DI5H
10
COM3
30
DI4L
9
NC2
29
DI4H
8
NO2
28
DI3L
7
COM2
27
DI3H
6
NC1
26
DI2L
5
NO1
25
DI2H
4
COM1
24
DI1L
3
NC0
23
DI1H
2
NO0
22
DI0L
1
COM0
21
DI0H