ADLINK Technology NuDAM-6018 User manual

6000 Series Analog Input Modules
The Optimal Choice for Harsh Environment
-6018 Thermocouple Analog Input Module
1. Introduction
NuDAM-6018 is a thermocouple input module with 8 input
channels. Six of the eight channels are differential and the
other two are single ended type.
Features
8 analog input channels
6 differential input and 2 single ended input
programmable input range
programmable host watchdog timer for host failure
protection
on board CJC for temperature measurement
2500 Vrms analog input isolation
internal watchdog timer for device failure protection
easy programming by software
easy installation and wiring
Specifications
Interface:
RS-485, 2 wires
Speed (bps): 600, 1200, 2400, 4800, 9600, 19.2k,
38.4k, 57.6k, 115.2k
Analog Input:
Differential channels: 6
Single ended channels: 2
Resolution: 16 bits
Accuracy: ±0.05%
Sampling rate: 10
Unit conversion: thermocouple, mV, V or mA
Thermocouple type: J, K, T, E, R, S, B, N and C
J: 0C ~ 760C K: 0C ~ 1370C
T: -100C ~ 400C E: 0C ~ 1000C
R: 500C ~ 1750C S: 500C ~ 1750C
B: 500C ~ 1800C N: -270C ~ 1300C
C: 0C ~ 2320C
Voltage range: programmable 6 levels:
±2.5V, ±1V, ±500mV, ±100mV, ±50mV, ±15mV
Current measurement: 20mA (with external 125
ohm resistor)
Isolation Voltage: 2500 Vrms
Note: The maximum input voltage shall not
exceed to ±30V with reference to AGND
otherwise, they may cause an unrecoverable
harm to the hardware component.
Storage Temperature Range: -25 to 80 C
Operating Temperature Range: -10 to 70 C
Power Requirement: +10V to +30VDC Unregulated
with against power reversal
Power Consumption: 0.70W
Case: ABS with captive mounting hardware
CE Class A Conformity
2. Pin Assignment
ND-6018
(Y)
DA
TA
+
(G)
DA
TA
-
(R)
+V
s
(B)
GN
D
8-CH Thermocouple
Input
1
10
Vin
5+
Vin
5-
Vin
6+
AG
ND
Vin
7+
DE
FA
UL
T
*
Vin
4-
Vin
4+
Vin
3-
Vin
3+
Vin
2-
Vin
2+
Vin
1-
Vin
1+
Vin
0-
Vin
0+
11
20
0E
0F
10
11
12
J
K
T
E
R
S
CODE
T/C
13
Pin Definitions
Pin #
Signal Name
Description
1
Vin5+
Differential positive input channel 5
2
Vin5-
Differential negative input channel 5
3
Vin6+
Single-ended input channel 6
4
AGND
Analog signal ground of channel 6 & 7
5
Vin7+
Single-ended input channel 7
6
DEFAULT*
Initial state setting
7
(Y)DATA+
RS-485 signal, positive
8
(G)DATA-
RS-485 signal, negative
9
(R)+VS
Power supply, +10V ~ +30Vdc
10
(B)GND
Ground
11
Vin0+
Differential positive input channel 0
12
Vin0-
Differential negative input channel 0
13
Vin1+
Differential positive input channel 1
14
Vin1-
Differential negative input channel 1
15
Vin2+
Differential positive input channel 2
16
Vin2-
Differential negative input channel 2
17
Vin3+
Differential positive input channel 3
18
Vin3-
Differential negative input channel 3
19
Vin4+
Differential positive input channel 4
20
Vin4-
Differential negative input channel 4
*The module is in DEFAULT mode when DEFAULT* pin
connected to GND while applying power on the module.
*Do not apply any power signal to DEFAULT* pin, just left
it open or connected it to GND.
3. Application Wiring
Differential Voltage Input
AGND
AGND
Differential
Signal
Source
<30V
IN(-)
IN(+)
ADC
Single Ended Voltage Input
Ground
Signal
Source
AGND
IN(+)
ADC
Current Input Measurement
Current
Source
R=125 Ohm
%1 accuracy
IN(-)
IN(+)
ADC
R
Thermocouple Input Measurement
<30V
IN(-)
IN(+)
ADC
AGND
AGND
4. Functional Block Diagram
5. Installation
Equipment for Installation
Aexisting RS-485 network
NuDAM modules
DC Power supply (+10V~+30V)
Wires for power, communication and I/O signal
Installation Procedure
1. Configure every single NuDAM module under the
administration utility
2. The baud rate setting and calibration procedure must be
done under the DEFAULT* mode
3. The baud rate and check-sum status must be identity
with the application network. The address ID must not
be conflict with other modules on the network
4. Plug the new module to the existing network
5. Use the NuDAM administration utility to check the
entire network
Power Input
+10V ~ +30V
+ 5V
Power
Regulator & Filter
Data+
Data -
GND
RS-485
Rec/Drv
Micro
Processor
EEPROM
Config Data
Safe Value
ADC
1-bit
Digital Input
8
Thermo-
couple
Input
channels
Default*
Pin
Mux
Watchdog/Power Failure
Supervisor

6000 Series Analog Input Modules
The Optimal Choice for Harsh Environment
6. Command Set
There are three categories of NuDAM commands. The first
is the general commands, including set configuration
command, read configuration, reset, read module‘s name or
firmware version, etc. Every NuDAM can response to the
general commands. The second is the functional commands,
which depends on functions of each module. Not every
module can execute all function commands. The third is the
special commands including functions about the
programmable watchdog timer, safe values, and the
programmable leading code. All the commands used in the
NuDAM analog input module are list in the following table.
Command
Syntax
General Command
Set Configuration
%(OldAddr)(NewAddr)
(InputRange)(BaudRate)
(DataFormat)
Read Configuration
$(Addr)2
Read Module Name
$(Addr)M
Read Firmware Version
$(Addr)F
Software Reset
$(Addr)RS
Functional Command
Span Calibration
$(Addr)0
Offset Calibration
$(Addr)1
Read Analog Data From
Channel N
#(Addr)(Channel No)
Read All Analog Data
#(Addr)A
Enable/Disable Channel for
$(Addr)5(ChannelVal)
Multiplexing
Read Channel Status
$(Addr)6
Read CJC Status
$(Addr)3
Enable/Disable Internal CJC
$(Addr)C(Status)
Read Enable/Disable Internal
CJC Status
$(Addr)D
* The module accepts calibration command, baud rate and
checksum configuration setting under the DEFAULT*
mode.
* Please refer the manual in PDF file format in the CD for
detail description of these commands.
7. ADLINK on the Internet
The full version manual can be download from website
http://www.adlink.com.tw/download/manual/index.htm#6000
Homepage http://www.adlink.com.tw
Service: [email protected]
Technical Assistance: [email protected]
Copyright 2000 ADLINK TECHNOLOGY INC.
TEL: [phone] FAX: [phone]
Contents and specification subject to change without notice.
NuDAMis a registered trademark of ADLINK TECHNOLOGY
INC. Other brands of products aretrademarks or registered
trademarks of their respective holders. AM-ND6018-E1.01