ADTRAN Total Access 300 Series User manual

1
DESCRIPTION
TheTotalAccess®361and362SingleFamilyUnit(SFU)OpticalNetwork
Terminations(ONTs)areGigabitPassiveOpticalNetwork(GPON)ONTs
withRFOverlay.TheTotalAccess361SFUONThas2POTS,and1
GigabitEthernetinterface.TheTotalAccess362has2POTS,and2Gigabit
Ethernetinterfaces.ThefigureaboveillustratestheSFUONTinner
enclosure.GPONtechnologyprovidesaconsistentandcommon
approachtoadvancingthepubliccommunicationsnetworkusing:
♦TraditionaltelephoneserviceisPlainOldTelephoneService(POTS)
♦Highspeeddataservices
♦Videoservices
TheGPONnetworkconsistsofanOpticalLineTerminal(OLT)locatedat
thecentralofficeandOpticalNetworkTerminals(ONTs)locatedatthe
customer’spremises.BetweenthemliestheOpticalDistributionNetwork
(ODN)consistingoffibersandpassivesplittersorcouplers.
Inordertoallowforthetransmissionofdownstreamandupstreamtraffic
ononesinglefiber,differentwavelengthsareusedforeachdirection.
Downstreamtrafficuses1490nm,whileupstreamtrafficiscarriedon
1310nm.ForoverlayRFTVdistribution,aseconddownstream
wavelengthof1550nmisused.
RF
Connection
RF Drop
Surface
Mounting
Hole
Surface Mounting
Hole
Hinge
Hinge
Security
Screw
Two-screw
Terminal
Bridges
Ethernet
Connections
Fiber Optic
Cable
Ground
Power
Ethernet Drop
POTS Drop
Ground and Power
Drop Callout
Ground Drop
Fiber Drop
RING
TIP
RING
TIP
FXS 0/1
FXS 0/2
ETH 0/1
ETH 0/2
POTS 1
POTS 2
ETH 1
ETH 2
TOTAL ACCESS 362 ONT
1187712G1
12V , 1A
CLEI
TIP RING
TEL. NUMBER
TIP RING
TIP RING
NETWORK STATUS
POTS 2
POTS 1
TELEPHONE TROUBLESHOOTING
1.Identify the bad line.
2.Disconnect the plug from the appropriate POTS jack and plug
any working telephone into that jack.
If the telephone works,there is a problem inside the house.
If the telephone does not work,contact your service provider.
3.Remove the telephone and replace the plug into the POTS jack.
4.Close the unit.
TIP RING
ETH 0/1
ETH 0/2
Total Access 300 Series
GigE SFU GPON ONTs
with RF Overlay
ThisJobAidcoverstheelectronicsmodules(SFUONT)andhousings
listedinthefollowingtable:
NOTE
TheTotalAccess361/362SFUONTsareonlyintendedtobeusedwiththe
CorningSystemsModelFNI‐NGseriesoutdoorNIDhousing.
FRONT PANEL LEDS
INSTALLATION
NOTE
RefertotheTot alAccess300GigESFUONTsInstallationGuide
(P/N6418771XGX‐5)forcompleteinformationoninstallingtheseunits.
AfterunpackingtheSFUONT,inspectitfordamage.Ifdamageisnoted,
fileaclaimwiththecarrierandthencontactADTRAN.Formoreinfor‐
mation,refertothewarranty.
Total Access 361 Description
1187711G1 TotalAccess361SFUElectronicsModule
4187711G12 TotalAccess361withSpliceHousing
4187711G13 TotalAccess361withOptiTapHousing
Total Access 362 Description
1187712G1 TotalAccess362SFUElectronicsModule
4187712G12 TotalAccess362withSpliceHousing
4187712G13 TotalAccess362withOptiTapHousing
Total Access SFU
Housings
Description
1187770G1 TotalAccessONTSpliceHousing
1187771G1 TotalAccessONTwithOptiTapHousing
Label Status Description
POWER {
z
Off
Green
Nopower
PowerisOn
NETWORK
STATUS
{
z
z
z
Off
Green
Yellow
Red
AdministrativelyShutDown
Normal
Testinprogress
FaultCondition
POTS
1 and 2
{
z
2
z
z
Off
Green
GreenFlashing
Yellow
Red
AdministrativelyShutDown
OffHook
Ringing
Testmode
Fault
ETH 1and 2 {
z
4
Off
Green
YellowFlashing
Linkisdown:noactivityor
AdministrativelyShutDown
10/100/1000Linkisup
TXorRXactivity
Product P/N: 418771XGX
Issue Date: March 2010
Document P/N: 6418771XGX-22B

26418771XGX-22B
MultiGroundedNeutral(MGN)ofthecustomerpremises.Ensure
thewireisfreeofanysharpbends.
5. Attachthegroundwiretothesideofthesubscriber’spremiseswith
stainlesssteelhalfmoonclampsortie‐wrapthegroundwiretothe
riserconduitoftheBuriedFiberDrop.
6. CleantheMGNconnectorwithemeryclothtoinsureastable
connection.
7. AttachthegroundwirefromtheSFUONTtotheMGNconnector
withtheappropriateULapprovedgroundclamp/fitting.
8. Coattheconnectionwithametalcorrosionpreventative.
9. AttachaWarningGroundTagtothisgroundingconnection.
Power/Alarm Connections
NOTE
WiringthePower/AlarmconnectorimproperlycoulddamagetheSFU.
TheSFUONTissuppliedwitha7‐conductorEuro‐stylePower/Alarm
connector.TomakeconnectionsfromtheUPStothepowerconnector
completethefollowingsteps:
1. RemovetheEuro‐Connectorbypullingitoutoftheelectronics
module.
2. Refertotheillustrationonthenextpageand“LocalPowerSource
Wiring”sectiontoassistincompletingthenextsteps.
3. Removetherubbergrommetfromthehousingandinsertthewire
throughthegrommet.
4. ToterminatethetwoUPSpowerleads(Pins6and7)and,ifneeded,
thefivealarmstatusleadsinthepowerconnector,cutallwiresand
stripbacktheinsulation.Useaflatheadscrewdriver(orsimilar
device)andloosenallthescrewsonthePowerAlarmConnector.
Insertonewireatatimeandtightenthescrewstomakeanelectrical
contact.
5. ReconnecttheEuro‐ConnectortothebottomoftheElectronics
Module.
6. TieWrapthewiresthroughtheholesjustbelowtheEuro‐style
connector.
7. ReplacetherubbergrommetwhileclosingtheElectronicsModule.
ThisplaceslessstressonthewiringandallowstheElectronics
Moduletoclosewithoutpinchinganywiring.
123
+ 12VDC
12V RTN
SIG RTN
ON BAT
REP BAT
BATMIS
LOW BAT
7654321
+ 12VDC
12V RTN
SIG RTN
ON BAT
REP BAT
BAT MIS
LOW BAT
765432
1
Euro-Connecto
r
Back of Electronics Module
Required Tools and Supplies
Standardtechniciantoolsandthoselistedbelowarerequiredfor
installingtheSFUONT:
♦Carpenter’slevel
♦3/32”screwdriverforconnectingSFUONTpower
♦5/32”hextamperproofbit
♦RJ‐45/RJ‐11crimper
♦Atelephony/datacommunicationtestset
♦PONpowermeterwithwavelengthfiltering
♦Fiberscopeorvideoscope
♦Two#10screwsandappropriatesurfaceanchorsformountingthe
SFUONT
♦Assortedtiewrapsforsecuringcablingandwiring
♦TwoRJ‐45plugs
♦TwoRJ‐11plugs(whennotusingtwo‐screwterminalbridges)
Forfiberopticconnections,thefollowingarerequired:
♦Fibersplicingtools
♦Fibercleaningmaterials
♦SC/APCfiberconnector
IncludedwiththeSFUONTpackagingare2two‐screwterminalbridges,
fibercablemanagementandstrainrelief,afiberconnector,and
electronics/optics.Fordata,theconnectiontotheSFUisthroughtheR‐J45
Ethernetconnectors.ForPOTS,theconnectionismadethroughtwo‐
screwterminalbridges,orRJ‐11connections.ForRFTVdistribution,the
connectionismadethroughacoaxialRFconnector.
Mount the Enclosure
Completethefollowingstepstomounttheenclosure:
1. Chooseaverticalsurfacenearanapprovedground,butawayfrom
downspouts,permanentwatersprinklers,orotherwatersources.
Thesubscribershouldhaveeasyaccessfortesting.
2. Usethetopandbottomexternalmountingholesasatemplateto
markfastenerlocations.Usealeveltoensuretheunitislevelto
preventwarping.
3. Pre‐drillthemarkedlocationsandinstallfastenersoranchors
appropriatetothemountingsurface(eachanchorratedto15lbs
minimum).
4. MounttheSFUONTtothesideofthesubscriber’spremise.
TheElectronicsModuleisinstalledinthehousingandswingsopenon
hinges.Toreleasethismodule,loosentheSecurityScrew(refertothe
illustrationonthefirstpage)andswingtheelectronicsModuletotheleft.
CAUTION
!
Donotuseaknifetocuttheopeningintherubbergrommets.Thismay
resultinanexcessivelylargeholeandcompromisetheintegrityofthe
unitallowingmoistureintotheunit.
Ground Connection
Installthegroundconnection(seeillustrationaboveright)bycompleting
thefollowingsteps:
1. Removetherubbergrommetfromthehousingandinserta#6solid
coppergroundwirethroughtherubbergrommet.
2. Usingthefigureontheoppositecolumn,routethegroundwireas
shownandattachittothegroundbar.
3. Replacetherubbergrommetbackinthehousing.
4. Routethegroundwire12inchesbelowfinishedgradebythe
shortestandmostdirectroutetotheACpowergroundsystem

6418771XGX-22B 3
Route OptiTap Fiber Drop Cable
Refertotheillustrationonthefollowingpageforfiberinstallations:
1. PlacetheOptiTapfiberdropinthesamerubbergrommetchannel
asthegroundcable.Thegroundcableshouldbe“below”theOpti‐
Tapfiber.
2. ConnecttheOptiTapfiber.
3. PlacetheOptiTapconnectorinthecut‐outinthehousing.
4. Connectthefibercabletotheconnectoronthebottomofthe
ElectronicsModule.
5. RoutethecablesothatwhentheElectronicsModuleisclosed,the
fiberisnotpinched.
NOTE
TherearewireroutingclipsonthelowerrightoftheElectronicsModule
housing.Itisrecommendedthatthesenotbeused.Routethepowerwires
sothattheyarenotpinchedwhentheElectronicsModuleisclosed.
Install SC/APC Optical Connection
NOTE
RefertotheTotalAccess300GigESFUONTsInstallationGuide
(P/N6418771XGX‐5)forinformationoninstallingtheSC/APCoptical
connection.
Toinstalltheopticalconnector,completethefollowing:
1. Withtheelectronicsmoduleswungopen,routethefiberthrough
themostdirectgrommetentranceandconnectittotheappropriate
SC/APCopticalconnection.
2. Checkthattherearenobendsinthefiberlessthan30mm(1.2
inches)radiusor60mm(approximately2.5inches)indiameter.
Whenthemaintenancedoorisclosed,itshouldnotcomeincontact
withthefiber.
Local Power Source Wiring
TheSFUONTneedstobepoweredbyaULListedPowerSupplysuitable
fortheapplicationwithOutputatLPSLevels.
ThisSFUONTshouldonlybeoperatedfromthetypeofcertified/listed
powersupplyrecommendedbythepowersupplymanufacturer.
Note: Do not tie wrap
the optical cable.
Route it as shown.
Ground Drop
Rubber Grommet
Tie Wrap
Opti-Tap Connector
+12VDC
12VRTN
SIGRTN
ONBAT
REPBAT
BATMIS
LOWBAT
765432
1
UsethePin‐Outinformationinthetablebelowasneeded.
Install UPS
InstallationoftheUninterruptiblePowerSource(UPS,P/N1187730G1)
willbedictatedbyon‐siteconditionsandlocaltelephonecompany
practices.
CAUTION
!
Usecautionwhenroutingwiresandcables.Avoidseverebendingand
routingoversharpedges.Usegrommetswhenpossibletoavoidwearon
cableinsulation.
1. InstalltheUPScablethatrunsfromtheSFUONTtothePower/
AlarmconnectoroftheUPSviathecustomerprovidedPVCcon‐
duit(ormethodusedbyyourlocaltelephonecompanypractice).
2. Swingtheelectronicsmoduleclosedandtightenthesecurityscrew
withthe5/32Hextamperproofbit.
3. Ifnecessary,tiewrapboththe#6groundwireandtheUPScable
runtotheBuriedFiberDropriserconduit.
POTS Connection
ThetelephoneserviceorPOTSconnectionscanbemadewitheithertwo‐
screwterminalbridges,orRJ‐11connectors.
Ifthetwo‐screwterminalbridgesareusedtheRJ‐11jacksprovidea
diagnostictestpoint.InsertinganRJ‐11jack(i.e.,telephonecableor
telephonetestset)willconnectthetelephonesettotheSFUONTandalso
disconnectthesubscriberservicefromtheSFUONTprovidingfault
isolationtotheSFUorpremiseswiring.
ToterminatethePOTSlinesonthetwo‐screwterminalbridgescomplete
thefollowing:
1. Trimeachwiretolengthandstripinsulation.Identifyeachpairin
theservicecable.
2. LoosenthescrewsfromtheTIP(green)andRING(red).
3. Wraptheappropriatewirearoundtheappropriatescrewand
tightenthescrewstosecuretheconnections.
POTScanalsobeconnecteddirectlytotheRJ‐11jack.Inthiscasethetwo‐
screwterminalbridgesbecomeisolatedandarenotused.
Pin-Out
Power/Alarm
Description Pin-Out
UPS
1LOWBAT 1
2BATMIS 2
3REPBAT 3
4ONBAT 4
5 SIGRTN 5
612VRTN 6
7+12VDC7
Pin 1
Pin 7
1
2
3
4
5
6
7
UPS Power
Connector
Power/Alarm
Connector
Low Battery
Battery Missing
Replace Battery
On Battery
Signal Return
12V Return
+12VDC
(Note: Refer to the sticker on the bottom
of the Power/Alarm Connector if needed)

For more information, refer to the Installation and Maintenance Practice (P/N 6418771XGX-5)
available online at www.adtran.com.
Warranty:ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
©2010 ADTRAN, Inc. All Rights Reserved. *6418771XGX-22B*
RF Connection
RoutetheRFcablethroughthelargegrommetatthebottomofthe
enclosureandattachittotheRFconnectorlocatedonbottomthe
electronicsModule.
Ethernet Connection
IftheONTisgoingtosupportupto1Gigabitoperation(10/100/1000),the
cableusedshouldberatedCAT‐6.Stripbackthejacketofthesubscriber
Ethernetcableandconnectthe4‐pairtwistedwirestotheRJ‐45Plug
usinganRJ‐45crimper.InserttheterminatedRJ‐45jackintotheappro‐
priateRJ‐45ETH socketontheSFUONT.ThetablebelowliststheEthernet
Connectionsandrelatedservices.

OPERATIONAL SPECIFICATIONS
♦OperationalTemperatureRange:–40°Cto+65°C
♦VoltageRange:10.5to15VDC
♦MaximumCurrent:1.5Amps
♦StorageTemperatureRange:–40°Cto+85°C
♦RelativeHumidity:95%,noncondensing
♦Dimensions:9.7”Wx12”Hx4”D
♦Weight:3lbs0.8oz(enclosureandelectronicsmodule)
♦OperatingAltitudeRange:–197feet(–60meters)to13000feet(3962
meters).Theoperatingambienttemperatureisderated1°C/1000feet
(3.3°C/km).
MAINTENANCE
TheSFUONTdoesnotrequireroutinehardwaremaintenancefornormal
operation.ADTRANdoesnotrecommendthatrepairsbeattemptedin
thefield.Repairservicesmaybeobtainedbyreturningthedefectiveunit
toADTRAN.Refertothewarrantyforfurtherinformation.Fieldsupport
forsoftwareisprovidedthroughupgradefacilities.
COMPLIANCE
TheTotalAccess300SeriesSFUONTsareNRTLListedtotheapplicable
ULsafetystandards.TheTotalAccess300SeriesSFUONTsmeetor
exceedalltheapplicablerequirementsofNEBS,andTelcordiaGR‐63‐
CORE.
TheTotalAccess300SeriesSFUONTsareintendedfordeploymentinthe
OutsidePlant(OSP)atlocationswheretheNECapplies(forexample,
CustomerPremises)andisintendedtobeinstalledbytrainedservice
personnel.ConfigurationCodesfortheSFUONTarelistedbelow.
Part Number Description Operation
1187711G1 ETH1Dataand/orVideo
1187712G1 ETH1
ETH2
Dataand/orVideo
Dataand/orVideo
Configuration Codes Input Output
PowerCode(PC) F C
TelecommunicationCode(TC) – –
InstallationCode(IC) A –
ThisdevicecomplieswithPart15oftheFCCrules.Operationissubjectto
thefollowingtwoconditions:
1. Thisdevicemaynotcauseharmfulinterference.
2. Thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
ChangesormodificationsnotexpresslyapprovedbyADTRANcould
voidtheuser’sauthoritytooperatethisequipment.
WARNING
!
The10/100/1000Base‐Tport(s)andPOTSareclassifiedasType4as
definedinAppendixBofGR‐1089‐COREIssue4,andaresuitablefor
connectiontointra‐buildingorunexposedwiringorcablingonly.Donot
metallicallyconnecttheseportstointerfaceswhichconnecttotheOutside
Plant(OSP)ortotheOSPwiring.The10/100/1000Base‐TportsandPOTS
aredesignedforuseasanintra‐buildinginterfaceonly(Type4portsas
describedinGR‐1089‐COREIssue4)andrequireisolationfromexposed
OSPcabling.TheadditionofPrimaryProtectorsisnotsufficient
protectioninordertoconnectthisinterfacemetallicallytoOSPwiring.
CAUTION
C
TheTotalAccess300SeriesSFUONTscontainaClass1LaserModule
whichcomplieswith21CFR1040.10and1040.11.
♦ ElectrostaticDischarge(ESD)candamageelectronicmodules.When
handlingmodules,wearanantistaticdischargewriststraptoprevent
damagetoelectroniccomponents.Placemodulesinantistaticpacking
materialwhentransportingorstoring.Whenworkingonmodules,
alwaysplacethemonanapprovedantistaticmatthatiselectrically
grounded.
♦ Thisequipmentmustbeconnectedtoaknown,reliableearthground
atalltimesduringinstallationandservice.RefertotheNational
ElectricalCode(NEC)andstate/localcodesfordetailsongrounding
requirements.A6AWGcoppergroundconductorshallbeusedto
connecttheequipmenttoearthground.
♦ PerGR‐1089‐COREtheTotalAccess300SeriesSFUONTsaredesigned
andintendedforinstallationaspartofaCommonBondingNetwork
(CBN).TheTotalAccess300SeriesSFUONTarenotdesignednor
intendedforinstallationaspartofanIsolatedBondingNetwork
(IBN).
♦ PerGR‐1089‐CORESection9,theSFUONTsdonothaveaninternal
DCconnectionbetween12Vandframeground.
♦ TheTotalAccess300SeriesSFUONTsChassisframegroundterminal
mustbeconnectedtoanearthgroundtoensuretheONTSFUis
properlygrounded.
NOTE
♦ Powersupplyinputandoutputconductorsofequipmentwhichare
outsideofthebuilding,areintendedtobelessthat140feetandhave
adequateclearancefrompowerandlightningconductorsin
accordancewithNEC725and800.FinalacceptanceoftheListed
equipmentinstallationwillultimatelybeuptothelocalAuthority
HavingJurisdiction(AHJ).
♦ Themainfeedisopticalandthereforenotclassifiedasanytypeofport
asdefinedinAppendixBofGR‐1089‐COREIssue4.
♦ TheTotalAccess300SeriesSFUONTsaredesignedtooperatewith
nominaloperatingvoltageof12VDCandaminimumoperating
voltageof10.5VDC.TheTotalAccess361and362willnotbe
damagedbyanysteadystatevoltagebetween10.5VDCand15.0VDC
inmagnitude.
C A U T I O N
C A U T I O N
!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807