ADTRAN Type 400 User manual

jobAid
1
DESCRIPTION
The ADTRAN 400 Small form-
Factor Pluggable (SFP ONT)
Optical Network Termination
(ONT) allows for network
equipment with a SFP Multi-source
Agreement (MSA) compliant SFP
cage to be supported over a GPON
network. The SFP ONT includes an SGMII interface to the
network element, as well as a SC/APC optical connector that
complies with ITU-T G.984.5.
The following features are supported on the SFP ONT:
■TX: 1310 nm
■RX: 1490 nm
■SC/APC Connector
■2.488 Gigabit downstream
■1.244 Gigabit upstream
■Supports Ethernet IEEE 802.1q/p and IEEE 802.3x
■Network configuration via ONT Management and Control
Interface
Specifications
Optical
■Data rate
♦2.488 Gbit/s downstream
♦1.244 Gbit/s upstream
■Optical transmit level: +0.5 dBm min, +5.0 dBm max
■Optical receive level sensitivity: -27.0 dBm max
■Optical distance: 20,000 meters
■Optical connectors: SC/APC
Operational
■Typical Current: 500 mA typical, 600 mA maximum
■Powers Dissipation: 1.8 watts typical, 2.0 watts max
Environmental
■Extended Environment (Industrial Grade)
■Operational temperature range: -40°C to +65°C
♦Case temperature hardened range: -40°C to +85°C
■Storage temperature range: -40°C to +85°C
■Relative humidity to 85%, noncondensing
ADTRAN 400
Small Form-factor Pluggable
Optical Network Termination
INSTALLATION
Inspect the SFP ONT. If damaged, file a claim with the carrier and
then contact ADTRAN Customer Care.
Installation Guidelines
The following are guidelines for this installation.
■The latch on the SFP ONT is for removal only. When removing
the SFP ONT, rotate the latch away from the SFP ONT cage
until a physical click occurs. The SFP ONT should slide easily
out of the cage.
■Ensure that the connector plug remains on whenever the
transceiver optical fiber connector is not inserted.
Installation Steps
To install the SFP ONT into a NetVanta, complete the following
steps:
1. Insert the SFP ONT into the appropriate NetVanta SFP cage
with the latch handle facing outward. Slide the SFP ONT all
the way into the SFP cage.
2. Using thumb and forefinger, exert adequate pressure to
ensure the SFP ONT is completely seated in the SFP cage.
3. Do not remove the connector plug until the optical fiber
connection is made.
4. Continue the installation and turn-up of the NetVanta unit
using the information provided with the unit.
PROVISIONING
The SFP ONT is provisioned via OMCI from the host GPON OLT.
MAINTENANCE
The SFP ONT does not require routine hardware maintenance for
normal operation. ADTRAN does not recommend that repairs be
attempted in the field. Repair services may be obtained by
returning the defective unit to ADTRAN. Refer to the warranty
for further information. Field support for software is provided
through upgrade facilities.
CLEI: BVL3AH0D_ _
Product P/N: 1287801F1
Issue Date: January 2016
Document P/N: 61287801F1-22B
Documentation for ADTRAN Carrier Networks products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following related online documents and resources provide additional information for this
product:
SFP/XFP/SFP+ Compatibility Matrix (Online Tool: www.adtran.com/SFP)

261287801F1-22B
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
This product is designed to meet the following environmental
classes:
■ETSI EN 300 019-1-1: “Classification of environmental
conditions; Storage,” Class 1.2
■ETSI EN 300 019-1-2: “Classification of environmental
conditions; Transportation,” Class 2.3
■ETSI EN 300 019-1-3: “Classification of environmental
conditions; Stationary use at weather-protected locations,”
Class 3.2
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.2 of ETSI EN 300
019-1-3.
This product meets EU RoHS Directive 2011/65/EU and/or
applicable exemptions. Refer to www.adtran.com for further
information on RoHS/WEEE.
FRANÇAIS
AVERTISSEMENT
!
Lisez tous les avertissements et mises en garde avant l’installation
de cet équipement ou la réalisation de toute opération de
maintenance.
ATTENTION
C
Ce produit utilise un module laser de classe 1 qui est conforme à
la norme 21 CFR 1040.10 et 1040.11, et IEC 60825-1 et EN 60825-1.
ATTENTION
!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■La borne de mise à la terre du châssis doit être branchée à une
prise de terre afin d’assurer que le boîtier métallique de la SFP
est correctement mis à la terre grâce au connecteur de face
arrière.
■Ce produit a une connexion interne entre le boîtier métallique
et la masse logique / signal, et ne peut être installé dans un
équipement hôte qui dispose également d' une connexion
entre la masse du châssis et la masse logique / signaux.
L'installation de ce produit dans un système hôte qui ne
dispose pas de connexion entre la masse du châssis et la masse
logique / signal peut entraîner la batterie revenir courant
circulant à travers le système hôte, l'équipement auxiliaire et le
câblage d'interconnexion. Cela peut causer des dommages au
système hôte, l'équipement auxiliaire, et le câblage
d'interconnexion.
SAFETY AND REGULATORY COMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
C
This product uses a Class 1 Laser module that complies with 21
CFR 1040.10 and 1040.11, and IEC 60825-1 and EN 60825-1.
CAUTION
!
■Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
■Per GR-1089-CORE the system is designed and intended for
installation as part of a Common Bonding Network (CBN).
■The system is not designed nor intended for installation as
part of an Isolated Bonding Network (IBN).
■This product has an internal connection between the metallic
housing and logic/signal ground, and can only be installed in
host equipment that also has a connection between chassis
ground and logic/signal ground. Installation of this product
into a host system that does not have a connection between
chassis ground and logic/signal ground can result in battery
return current flowing through the host system, ancillary
equipment and interconnect cabling. This may cause damage
to the host system, ancillary equipment, and interconnect
cabling.
■The ADTRAN system chassis frame ground terminal must be
connected to an earth ground to ensure that the metal
enclosure of the SFP is properly grounded via the backplane
connector.
■Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
NOTE
■This product is compliant with SFF-8472 “Digital Diagnostics
Monitoring Interface for Optical Transceivers,” Revision 9.3.
■This product is designed to be deployed in GR-3108-CORE
environmental class 1 or 2 as defined in GR-3108-CORE.
■Changes or modifications not expressly approved by
ADTRAN could void the user's authority to operate this
equipment.
■This product complies with 21 CFR 1040.10 and 1040.11 except
for deviations pursuant to Laser Notice No. 50, dated June 24,
2007.
Configuration Code Input Output
Power Code (PC) F C
Telecommunication Code (TC) – X
Installation Code (IC) A –

61287801F1-22B 3
REMARQUE
Les changements ou modifications non expressément approuvés
par ADTRAN pourraient annuler l'autorisation de l'utilisateur
d’utiliser cet équipement.
Ce produit est conçu pour répondre aux classes environnemen-
tales suivantes:
■ETSI EN 300 019-1-1: “Classification des conditions
d'environnement; Entreposage,” Classe 1.2
■ETSI EN 300 019-1-2: “Classification des conditions
d'environnements; Transport,” Classe 2.3
■ETSI EN 300 019-1-3: “Classification des conditions
d'environnements; l'utilisation à poste fixe dans des endroits
protégés contre les intempéries,” Classe 3.2
L'équipement est conçu pour fonctionner sans dégradation lors
des tests à tous les niveaux de sévérité, suivant les spécifications
de la classe 3.3 de l'ETSI EN 300 019-1-3..
Ce produit est conforme à la directive européenne RoHS 2011/
65/EU et/ou aux exonérations applicables. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.

Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service.
Warranty information can be found online at
www.adtran.com/warranty.
©2016 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61287801F1-22B*
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED