ADTRAN Job Aid+ 1442910G2 User manual

jobAid
DESCRIPTION
The 8 Gigabit Fibre Channel 10 Km XFP, 1310 nm (XFP) optical
transceiver is a fully duplex serial electric, serial optic device. It
has both transmit and receive functions and provides a high
speed serial link at 8.5 Gb/s. Installed into an appropriate host
module, the XFP provides a 8 Gigabit interface to the supporting
system.
The transmit side of the XFP converts serial NRZ electrical data at
the 8.5 Gb/s line rate to a standard compliant optical signal. The
receive side of the XFP converts the incoming DC balanced serial
NRZ optical data at the 8.5 Gb/s line rate into serial electrical
data.
NOTE
To ensure compatibility, refer to the ADTRAN documentation
provided with the host module.
The XFP has the following features:
1310 nm optical signals for up to 10 km reach
Low power consumption (<2.0 W max for 10 km)
Bit error rate (<1x10-12)
Excellent EMI performance
CAUTION
!
Due to compliance certification requirements, use only XFPs
supplied by ADTRAN with the host module. ADTRAN cannot
certify system integrity with other XFPs.
Small Form-Factor Pluggable
8 Gigabit Fibre Channel 1310 nm 10 km XFP
Operational Specifications
Optical Specifications:
oTransmit wavelength: 1260 to 1355 nm (1310 nm nominal)
oReceive wavelength: 1260 to 1600 nm
oData rate: 8.5 Gb/s (8G Fibre Channel)
oOptical transmit level: –8.2 to +0.5 dBm
oOptical receive level: –14.4 to +0.5 dBm
oOptical distance: 10 km maximum
oOptical connectors: LC
Extended Environmental Support:
oOperational temperature range: –40°C to +85°C
oStorage temperature range: –40°C to +85°C
oRelative humidity to 85%, noncondensing
INSTALLATION
Inspect the XFP. If damaged, file a claim with the carrier and then
contact ADTRAN Customer Service.
To install the XFP into an appropriate module, complete the
following steps:
1. Insert the XFP into the XFP cage on the circuit board of the
host module with the latch handle facing outward. Slide the
XFP all the way into the receptacle.
NOTE
The latch on the XFP is for removal only. When removing the
XFP, rotate the latch away from the XFP cage until a physical click
occurs. The XFP should slide easily out of the cage.
2. Using thumb and forefinger, exert adequate pressure to
ensure the XFP is completely seated in the XFP cage.
3. Do not remove the connector plug until the optical fiber
connection is made.
NOTICE
We recommend that the connector plug remain on whenever the
transceiver optical fiber connector is not inserted.
4. Continue the installation and turn-up of the host module
using the instructions in the Job Aid provided with that
module, or by using the applicable Total Access 5000 Series
Deployment Guide or User Interface Guide, available online
at www.adtran.com.
CLEI: BVL3AXPD__
Product P/N: 1442910G2
Issue Date: November 2013
Document P/N: 61442910G2-22A
Documentation for ADTRAN Carrier Networks products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following documents provide additional information for this product:
SFP/XFP/SFP+ Compatibility Matrix and Engineering Guide

C A U T I O N
C A U T I O N
!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Warranty: ADTRAN will replace or repair this product
within the warranty period if it does not meet
its published specifications or fails while in
service. Warranty information can be found
online at www.adtran.com/warranty.
©2013 ADTRAN, Inc. All Rights Reserved. *61442910G2-22A*
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
SAFETY AND REGULATORY COMPLIANCE
Read all warnings and cautions before installing or servicing
this equipment.
CAUTION
C
This product is a Class 1 Laser Product and complies with the
Laser Safety requirements of FDA 21CFR 1040.10 and 1040.11,
and EN60825-1 and -2. The XFP is NRTL listed and CB Certified
to all applicable American and European safety standards.
For continued compliance with the above laser safety standards,
only approved Class 1 modules from our approved vendor list,
located on the ADTRAN website, should be installed in ADTRAN
products.
CAUTION
!
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
This product meets or exceeds all the applicable requirements
of NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. This
product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises). This product is to be
installed in ADTRAN products in Restricted Access Locations
only, and installed by trained service personnel.
Per GR-1089-CORE, the ADTRAN system in which this
product is being deployed is designed and intended for
installation as part of a Common Bonding Network (CBN).
The ADTRAN system in which this product is being deployed
is not designed nor intended for installation as part of an
Isolated Bonding Network (IBN).
Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. The XFP can be installed in a DC-I (isolated) or DC-C
(common) installation. For installations where other cards or
the host system have internal connections between battery
return and frame ground, the system would be intended for
deployment only in a DC-C installation.
The ADTRAN system chassis frame ground terminal must be
connected to a reliable earth ground to ensure that the metal
enclosure of this product is properly grounded via the
backplane connector.
NOTE
The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE Issue 6.
This product is designed to meet the following environmental
classes:
GR-3108-CORE Environmental Classes 1, 2, and 3.
ETSI EN 300 019-1-1 “Classification of environmental
conditions; Storage,” Class 1.2
ETSI EN 300 019-1-2 “Classification of environmental
conditions, Transportation,” Class 2.3
ETSI EN 300 019-1-3 “Classification of environmental
conditions, Stationary use at weather-protected locations,”
Class 3.3
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.3.
This device complies with FCC 47 CFR Part 15, Class B. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.