ADTRAN SFP User manual

Q
uic
k
Start
DESCRIPTION
The Total Access 5000 Optical Line Terminal (OLT) 2.5G/1.25G,
Class C++ Small Form-factor Pluggable (SFP) is specifically
designed for Gigabit Passive Optical Network (GPON) applica-
tions. It facilitates high performance, integrated, bidirectional data
transmission over one, single mode optical fiber.
The 2.5G/1.25G, Class C++ GPON OLT can be used with the
SDX OLTs and Total Access 5000 OLT solutions that support
GPON.
The SFP incorporates a 1490 nm, DFB laser diode for streaming
2.488 Gbps downstream data and an APD/TIA burst mode
receiver for 1310 nm,1.244 Gbps, upstream data.
It is FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1 Class I
laser safety compliant and meets the EU RoHS Directive.
g NOTE
To ensure compatibility, refer to the documentation provided with
the host module.
FEATURES
The following features are supported on the SFP:
■SC Simplex receptacle
■Hot pluggable
■Transmit wavelength: 1490 nm
■Receive wavelength: 1310 nm
f CAUTION!
Due to compliance certification requirements, only SFPs supplied
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other SFPs.
INSTALLATION
Before installation, inspect the SFP. If damage has occurred
during shipping, file a claim with the carrier and then contact
ADTRAN Customer Support. For more information, refer to the
warranty.
Changes or modification not expressly approved by ADTRAN will
void the warranty.
Installation Steps
To install the SFP, complete the following steps:
g NOTE
Do not remove the protective dust covers from the SFP until the
fiber optic cable is ready to be connected.
1. Insert the SFP into the SFP cage on the equipment or
device with the latch handle facing upward.
2. Slide the SFP all the way into the cage until there is an
audible “click.”
g NOTE
■Orientation of the SFP will vary depending on the equipment.
■The latch on the SFP is for removal only. When removing the
SFP, rotate the latch away from the SFP. It should easily slide
out of the cage.
w NOTICE
Do not remove the protective dust cover until the optical fiber
connection is made. Ensure that you keep the protective dust
cover on whenever the transceiver optical fiber connector is not
inserted.
3. Continue the installation and turn-up of the host device or
equipment using the instructions in the Job Aid or Quick
Start provided with the equipment or device or other system-
level documentation available online at www.adtran.com.
ADTRAN Pluggable Optics
SFP
2.5G/1.25G, Class C++ GPON OLT
November 2020
61442541F1-13A
1442541F1

261442541F1-13A
SPECIFICATIONS
Specifications for the SFP are as follows:
General
■Module Type: SFP
■Media Type: Fiber
♦Single-Mode
♦Single-Fiber
■Signal Data Rate:
♦2.488/1.244 Gbps (GPON TX/RX)
■Not compatible with SFP+ MSA
■Applications: GPON, FTTH, FTTB, FTTC
■Optical Connector: SC
Optical
♦Data rate:
●Receive: 1.244 Gbps
●Transmit: 2.488 Gbps
♦Optical connectors: SC, UPC
■Transmitter
♦Transmitter Type: 1490 nm DFB Laser, CW Mode
♦Optical Center Wavelength: 1490 nm
♦Average Launch Power: +4.5 dBm to +10.0 dBm
♦Spectral Line Width @ –20.0 dB: 1 nm
♦SMSR: 30.0 dB
♦Extinction Ratio: 8.2 dB
■Receiver
♦Receiver Type:1310 nm APD/TIA, BM
♦Optical Center Wavelength: 1310 nm
♦Receiver Sensitivity: –30.0 dBm
♦Receiver Overload: –12.0 dBm
Environmental
■Protected Equipment Severe Environment (Outdoor)
♦System Ambient Operational Temperature Range: –40°C to
+70°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity: 5% to 95%, non-condensing
SAFETY AND REGULATORY
f WARNING!
Read all warnings, cautions, notes and installation instructions
before installing or servicing this equipment.
CCAUTION!
This product is a Class 1 Laser that complies with FDA 21 CFR
1040.10 and 1040.11 and IEC 60825-1. The product is NRTL
Listed and CB Certified to all applicable American and European
safety standards.
f CAUTION!
■Electrostatic Discharge (ESD) can damage electronic devices.
When handling devices, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place in
antistatic packing material when transporting or storing. When
installing or maintaining, always place devices on an approved
antistatic mat that is electrically grounded.
■This product’s outer case is “electrically isolated” from other
circuits, as a result, this product can be used in systems that
are installed either in a DC-I (isolated) or DC-C (common)
configuration. For Systems where other installed modules or
the host system itself have internal connections between
battery return and frame ground, the system can only be
deployed in a DC-C configuration.
■If the host system has a protective earth (PE) terminal, the PE
terminal of the host system must be connected to protective
earth (PE) to ensure that the exposed metal (i.e., front panels,
optical modules) on the product is properly grounded.

61442541F1-13A 3
g NOTE
■This product is designed to be deployed in GR-3108-CORE
environmental Class 1, 2, or 3.
■This product is NRTL Listed to the applicable UL/CSA
Standards. The product is designed to meet the applicable
requirements of Telcordia GR-63-CORE, GR-1089-CORE,
and GR-3108-CORE. This product has also been evaluated to
applicable international standards.
■This product is intended for deployment in locations such as
telecommunications facilities (e.g., Central Offices), outdoor
electronic equipment cabinets and at locations where the NEC
applies (such as customer premises). This equipment is
intended to be installed and used only by instructed or skilled
persons. This product is to be installed only in restricted
access locations.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-1-1 “Classification of environmental 
conditions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of environmental 
conditions, Transportation,” Class 2.3
♦ETSI EN 300 019-1-3 “Classification of environmental 
conditions, Stationary use at weather protected locations,”
Class 3.3
■This product is designed to function without degradation
during exposure to all test severities per Class 3.3 of ETSI EN
300 019-1-3.
■This equipment contains no parts that can be serviced by the
user.
■This product meets EU RoHS Directive. Refer to
www.adtran.com/environmental for further information on
RoHS/WEEE.
FRANÇAIS
f AVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C ATTENTION!
Ce produit est un module laser de classe 1 qui est conforme à la
FDA 21 CFR 1040.10 et 1040.11 et IEC 60825-1. Ce produit est
NRTL et Certifié CB à toutes les normes de sécurité applicables
américains et européens. Pour maintenir la conformité avec les
normes ci-dessus, installer des modules laser de classe 1 ne
ADTRAN approuvés dans les produits d'ADTRAN.
f ATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■Si le système hôte est doté d'une borne de mise à la terre de
protection (PE), la borne PE du système hôte doit être
connectée à la mise à terre de protection (PE), afin d'assurer
que les parties métaliques à découvert (panneaux frontaux,
modules optiques) du produit soient correctement mis à terre.
g REMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com/environmental pour de plus
amples renseignements sur RoHS.

DEUTSCH
f WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
C VORSICHT!
Dieses Produkt ist ein Klasse 1 Laser, die mit FDA 21 CFR
1040.10 und 1040.11 und IEC 60825-1 entspricht. Das Produkt ist
NRTL gelistet und CB Certified allen geltenden amerikanischen
und europäischen Sicherheitsnormen.
f VORSICHT!
■Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Falls das Host-System über einen Schutzleiteranschluss (PE)
verfügt, muss der PE-Anschluss des Host-Systems mit dem
Schutzleiteranschluss (PE) verbunden werden, um
sicherzustellen, dass das freiliegende Metall (d. h.
Frontblenden, Optikmodule) am Produkt ordnungsgemäß
geerdet ist.
g HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen Sie
www.adtran.com/environmental für ausführlichere Informationen
zu RoHS/WEEE.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2020 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442541F1-13A*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)